Brass Products Master Catalog
Product Focus

Table of Contents
Application Data
Important Safety Information Visual Index Numbering Systems Tube Connector Selector Chart Thread Identification Tubing Selection Flare Dimensions Tubing Installation Chemical Compatibility Chart
Tubing
Plastic Tubing
Brass Products
Introduction Inverted Flare SAE 45o Flare Compression SelfalignTM PolylineTM Flareless Push>ConnectTM Push>Connect Metric Push>Connect Flow Controls Push>Connect Plus Mini-Barb Quick>ConnectTM Air Brake Air Brake Products for Nylon Tubing Air Brake Products for Copper Tubing Threaded Sleeve Pipe Needle Valves Drain Cocks Truck Valves Plastic Drain Cocks Ground Plug & Multiple Shut-Offs Brass Ball Valves Special Adapter Hydralic Brake Products Steel Brake Lines
Plastic Products
1 Molded Compression Tube Products 126
2 Plastic Products 134
8 Brass – Nickel Plated
9 BSPP Products 135
10
15 Related Products
19 Air Brake Products & Measuring Kits 136
21 Assembly & Tool Cutting Equipment 137
22 Tube Cutting Equipment 138
Tube Bending Tools 139
27 Tube Flaring & Brazing Tools Label Sets & Bags 140 141
Cabinets & Assortments 142
30 Certification
31 36 ISO & QS Certifications 146
41 Conversion
47 Conversion Charts 147
53 57 64 Glossary Alpha/Numeric index 149
68 Index
70 Alpha/Numeric Index 152
72 76 84 Warranty Eaton Warranty 156
90
95
97
103
107
110
111
112
115
119
123
125

Application Data

Important Safety Information

WARNING
Selection of Tubing
Selecting the proper tubing for a given application is essential to the proper operation and safe use of the tubing and related equipment. Inadequate attention to the selection of the tubing for your application can result in leakage, bursting, or other failure which can cause serious bodily injury or property damage from spraying fluids or flying projectiles. In order to avoid serious bodily injury or property damage resulting from selection of the wrong tubing, you should carefully review the information in this catalog. Some of the factors that are involved in the selection of the proper tubing are:

. material of tubing

. bends

. tubing size

. temperature

. tubing length

. tubing pressure rating

. tubing end connections

. installation design

. fluid conveyed

(compatibility)
These factors and the other information in this catalog should be considered by you in selecting the proper tubing for your application. If you have any questions regarding the proper tubing for your application, please contact Eaton Technical Support 1-888-258-0222.

Proper Selection of Tube Fittings
Selection of the proper Eaton tube products for the application is essential to the proper operation and safe use of tubing and related equipment. Inadequate attention to the selection of the products for your application can result in tube leakage, bursting, or other failure which can cause serious injury or property damage from spraying fluids or flying projectiles. In order to avoid serious bodily injury or property damage resulting from selection of the wrong tube end fitting, you should carefully review the information in this catalog. Some of the factors which are involved in the selection of the proper products are:

. tube end connections

. installation design

. compatibility with tubing

. tubing size

. temperature

. corrosion requirements

These factors and the other information in this catalog should be considered by you in selecting the proper tube ends for your application.
If you have any questions regarding the proper tube ends for your application, please contact Eaton Technical Support at 1-888-258-0222.
Tubing Installation
Proper installation of the tubing is essential to the proper operation and safe use of the tubing and related equipment. Improper installation of the tubing can result in serious injury or property damage. In order to avoid serious bodily injury or property damage resulting from improper installation of the tubing, you should carefully review the information in this catalog regarding tubing installation.
Some of the factors you must consider in installing the tubing properly are:
. proper installation
procedures

. changes in length

. protection from high

temperature sources

. twisting

. stress

. rubbing and abrasion

These factors and other information in this catalog regarding tubing installation should be considered by you before installing the tubing.
If you have any questions regarding proper installation of the tubing, please contact Eaton Technical Support 1-888-258-0222.
Tubing Assembly
Changes in materials, finishes, and assembly techniques may affect the sealing or holding capability of the joint. Due to the great variety of possible assembly scenarios, assembly procedures should be tested to determine if the joint is adequate for its intended use. Improper assembly or overtightening could result in leakage, tubing separation or other failures which could cause serious bodily injury or property damage from spraying fluids or flying projectiles.
These factors and other information in this catalog regarding tubing assembly should be considered by you before installing the tubing.
If you have any questions regarding proper assembly and installation of the tubing, please contact Eaton Technical Support 1-888-258-0222.
Dimensions
Dimensions given in this catalog are approximate and should be used for reference only. Exact dimensional information for a given product is subject to change and varying tolerances. Check with Eaton Technical Support at 1-888-258-0222 for critical applications.

Application Data

Visual Index
Inverted Flare Tube Nut (Steel) Tube Nut (Brass) Plug (Steel) Tube Nut Long Union Adapter SAE 45° (Steel) Flare to Inv. Flare
105x 100x 131x 7896x 252x pg. 32 pg. 32 pg. 32 pg. 32 pg. 32 pg. 33
Male Connector Female Connector 45° Male Elbow Union ElbowMale Elbow
202x 252x 352x 502x 402x pg. 33 pg. 33 pg. 33 pg. 34 pg. 34
Female Elbow Union Tee Male Run Tee Male Branch Tee Female Branch Tee
452x 702x 752x 602x 652x pg. 34 pg. 35 pg. 35 pg. 35 pg. 35
SAE 45o Flare Nut Long Nut Cap Plug Union Male Connector
1110x 41x 40x 39x 42x 48x pg. 37 pg. 37 pg. 37 pg. 37 pg. 37 pg. 38
Female Connector Male Ball Check 45° Male Elbow AC Type AdapterAdapter SAE 45° Union Elbow Connector Flare to Inv. Flare
46x 43x 54x 55x pg. 38 pg. 38 pg. 38 pg. 39 pg. 39 pg. 39
Male Elbow Female Elbow Union Tee Male Run Tee Male Branch Tee Adapter Tee
49x 50x 44x 51x 45x 56x pg. 39 pg. 39 pg. 40 pg. 40 pg. 40 pg. 40
Compression and Tube Support for Sleeve Nut Long Nut Bulkhead Nut Union SelfAlign Products Plastic Tubing
2030x 60x 601x 61x 611x 1611x 0102x 62x 621x pg. 42 pg. 42 pg. 42 pg. 42 pg. 49 pg. 43 pg. 43 pg. 43 pg. 43
Male Connector Female Connector Male Ball Check Bulkhead Union Male Elbow Union Elbow Connector
68x 681x 66x 661x 63x 631x 74x 741x 69x 691x 65x 651x pg. 43 pg. 50 pg. 44 pg. 50 pg. 44 pg. 50 pg. 44 pg. 51 pg. 45 pg. 51 pg. 45 pg. 51
Female Elbow Union Tee Male Run Tee Male Branch Tee Adapter Tee .
70x 701x 64x 641x 71x 711x 72x 721x 76x pg. 45 pg. 51 pg. 46 pg. 52 pg. 46 pg. 52 pg. 46 pg. 52 pg. 46

Application Data

Visual Index

Plastic Sleeve Brass Nut Brass Nut/Plastic Brass Bulkhead Nut Union Male Connector Sleeve Assembly
Polyline Flareless

1260x 1261x-1261x-Ax 1202x-A 1262x 1268x pg. 54 pg. 54 pg. 54 pg. 54 pg. 54 pg. 55
Female Connector Bulkhead Union Male Elbow Female Elbow Union Tee Male Run Tee
1266x 1274x 1269x 1270x 1264x 1271x pg. 55 pg. 55 pg. 56 pg. 56 pg. 56 pg. 56
Male Branch Tee
1272x pg. 56

Push>Connect Cartridge Plug (Plastic) Double Union Reducer Stem Adapter Union
Metric 1161x Metric 1129x Metric 1105x Metric 1109x Metric 1180x Metric 1612x pg. 64 pg. 59 pg. 64 pg. 59 pg. 64 pg. 59 pg. 64 pg. 59 pg. 64 pg. 60 pg. 64 pg. 60
Bulkhead Union Union "Y" Male "Y" Male Connector Female Connector Union Elbow
Metric 1174x Metric 1107x Metric 1108x Metric 1168x Metric 1166x Metric 1165x pg. 65 pg. 60 pg. 65 pg. 60 pg. 65 pg. 61 pg. 65 pg. 61 pg. 65 pg. 61 pg. 66 pg. 61
Swivel Male Elbow Male Elbow Union Tee Male Run Tee Swivel Male Branch Tee Stud ManifoldsSwivel
Metric 1169x-S Metric 1169x Metric 1164x Metric 1171x-S 1168x pg. 66 pg. 62 pg. 66 pg. 62 pg. 67 pg. 62 pg. 67 pg. 62 pg. 67 pg. 63 pg. 63
BanjosFlow Controls
pg. 63 pg. 69

Push > Connect Plus see page 70.
Mini-Barb Plug Solder Connector Union Male Connector Female Connector Compression Connector
1073x 1079x 1062x 1068x 1066x 1078x pg. 73 pg. 73 pg. 73 pg. 73 pg. 73 pg. 73
Bulkhead Bulkhead Union Union Elbow 90o Male Elbow 90o Female Elbow Union Tee
Compression
Connector

1067x 1074x 1065x 1069x 1070x 1064x pg. 74 pg. 74 pg. 74 pg. 74 pg. 74 pg. 75
Male Run Tee Male Branch Tee Female Branch Tee Adapter Tee .
1071x 1072x 1077x 1075x pg. 75 pg. 75 pg. 75 pg. 75

Application Data

Visual Index
Quick>Connect Encapsulated Union Bulkhead Union Female Bulkhead Male Connector Female Connector Air Brake Cartridge Union
1861x 1862x 1874x 1873x 1868x 1866x pg. 78 pg. 78 pg. 78 pg. 78 pg. 79 pg. 79
45. Male Elbow Swivel Male 45o Union Elbow Male Elbow 90o Male Elbow 90o Swivel Male 90o Elbow Long Elbow
1880x 1880x-S 1865x 1869x 1869x-L 1869x-S pg. 79 pg. 80 pg. 80 pg. 80 pg. 80 pg. 81
Female Elbow Union Tee Male Run Tee Swivel Male Run Tee Male Branch Tee Swivel Male Branch Tee
1870x 1864x 1871x 1871x-S 1872X 1872x-S pg. 81 pg. 81 pg. 81 pg. 82 pg. 82 pg. 82
Female Branch Tee Adapter Tee Pressure Plug
1877x 1883x 1829x
pg. 82 pg. 83 pg. 83

Air Brake Connectors Sleeve Nut Union Male Connector Female Connector Bulkhead Union for Nylon Tubing
1460x 1461x 1462x 1468x 1466x 1474x pg. 85 pg. 85 pg. 85 pg. 86 pg. 86 pg. 86
45o Male Elbow Union Elbow 90o Male Elbow 90o Male Elbow 90o Female Elbow Union Tee Long
1480x 1465x 1469x 1469x-L 1470x 1464x pg. 86 pg. 87 pg. 87 pg. 87 pg. 87 pg. 88
Male Branch Tee Female Branch Tee Male Run Tee Adapter Tee Insert Gauge Ring
1472x 1477x 1471x 1482x 1484x 1485x pg. 88 pg. 88 pg. 88 pg. 89 pg. 89 pg. 89

Application Data

Visual Index

Air Brake Connectors Sleeve Nut Union Male Connector Female Connector 45o Male Elbow for Copper Tubing
1360x 1361x 1362x 1368x 1366x 1380x pg. 91 pg. 91 pg. 91 pg. 91 pg. 92 pg. 92
90o Male Elbow 90o Male Elbow Long Union Tee Male Run Tee Male Branch Tee Bulkhead Coupling (brass)
1369x 1369x-L 1364x 1371x 1372x pg. 92 pg. 92 pg. 93 pg. 93 pg. 93 pg. 93
Bulkhead Coupling Bulkhead Coupling Drain Cock Shut-Off Valve External Seat .(brass)(brass)Draincock
W15310 W2033L 145 pg. 94 pg. 94 pg. 94 pg. 94 pg. 94
Threaded Sleeve Nut Male Connector Male Elbow
6100x 6200x 6400x
pg. 96 pg. 96 pg. 96

Pipe Cap Slotted Plug Square Head Plug Hex Head Plug Hex Socket Plug Adapter
3129x 3150x 3151x 3152x 3153x 3200x pg. 98 pg. 98 pg. 98 pg. 98 pg. 98 pg. 98
Bushing Union Coupling Reducer Coupling Restriction Pipe Hex Nipple Adapter
3220x 3250x 3300x 3300x 3325x pg. 99 pg. 99 pg. 99 pg. 99 pg. 99 pg. 100
Close Nipple Long Nipple Bulkhead Coupling 45° Street Elbow 90° Street Elbow (brass)
3326x 3311x 3350x 3400x pg. 100 pg. 100 pg. 101 pg. 101 pg. 101
90. Elbow Male Branch Tee Tee Male Run Tee Cross .
3500x 3600x 3700x 3750x 3950x pg. 102 pg. 102 pg. 102 pg. 102 pg. 102

Application Data

Visual Index
Needle Valves Compression DoubleCompression Compression AngleInverted Male Pipe DoubleMale to Female PipeStraightwayStraightway
pg. 104 pg. 104 pg. 104 pg. 104 pg. 105 pg. 105
Female PipeSAE 45° Flare DoubleSAE 45° Flare SAE 45° Flare AnglePolyline Poly AngleStraightwayStraightway
pg. 105 pg. 105 pg. 106 pg. 106 pg. 106 pg. 106
Drain Cocks External SeatExternal SeatInternal SeatInternal Seat (long)Internal SeatInternal Seat Drain Valve
pg. 107 pg. 107 pg. 107 pg. 107 pg. 108 pg. 108
Air VentAngle Bib DrainAngle Bib DrainHose to Pipe (steel)Hose to Pipe (steel)Pipe to Hose Shut-Off
pg. 108 pg. 108 pg. 108 pg. 109 pg. 109 pg. 109
Gasoline Shut-OffAir Tank Drain Valve.
pg. 109 pg. 109

Truck Valves Truck Valve Truck Valve Truck Valve Truck Valve Truck Valve
7502 7504 7506 7508 7509 pg. 110 pg. 110 pg. 110 pg. 110 pg. 110

Application Data

Visual Index
Ground Plug &

Multiple Shut-Offs DraincockGround Plug DrainSAE 45° Flare SAE 45° Flare Compression Compression DoubleStraightwayDoubleStraightway
pg. 112 pg. 112 pg. 112 pg. 113 pg. 113 pg. 113
Male to Female PipeTruck Shut-Off to Marine Shut-Off Female Pipe3-Way Shut-Off3-Way Multiple Female PipeMale to Female PipeShut-Off
UL
L

pg. 113 pg. 113 pg. 114 pg. 114 pg. 114 pg. 114
4-Way Multiple Plastic Drain Cocks Brass Ball Valves Special Adapters Hydraulic Brake BSPP Products Shut-OffProducts
L

C
pg. 114 pg. 111 pg. 115 pg. 119 pg. 123 pg. 135
Molded Compression Male Connector Union Connector Bulkhead Union Female Connector Male Elbow Female Elbow Tube Fittings
1568x 1562x 1574x 1566x 1569x 1570x pg. 128 pg. 128 pg. 129 pg. 129 pg. 130 pg. 130
Union Elbow Male Branch Tee Union Tee Male Run Tee Compression Nut Insert
1565x 1572x 1564x 1571x 1561x 1584x pg. 131 pg. 131 pg. 131 pg. 132 pg. 132 pg. 132
Cap Nut Bulkhead Nut Kynar Check Valve
1529x 1502x 1531x pg. 133 pg. 133 pg. 133

Plastic Barbed Fittings Straight Connector Universal Connector Elbow Connector Universal Tee 3 Way T Y Connector
A A C C
B A A
B B B

pg. 134 pg. 134 pg. 134 pg. 134 pg. 134 pg. 134
4 Way Tee 5 Way Tee

pg. 134 pg. 134

Application Data

Numbering Systems
Parts in this catalog are identified by a series of numbers separated by the letter “X.”
1. The number preceding 48 X 6 the “X” is the Catalog “Base Number” and indi
1 2

cates the type of connector. See Table 1 below for additional base number data (sometimes referred
to as dash size).
2. The second number is
48 X 6 X 2 the tube and/or pipe size

in sixteenths of an inch. 1 23 When a pipe thread
for a given tube size
follows the SAE standard as shown in Table 2, no other number is required. Example: 48X6 = SAE 45° Flare Male Connector–3/8" tube, 1/4" Male Pipe.
3. If the pipe size is not to
the SAE standard, another “X” is added followed by
the pipe size indicated
in sixteenths of an inch. Example: 1/8" is equal to 2/16" or X2 suffix.
In designating tube and pipe
sizes for tees and crosses
that are not SAE standard,
indicate the sizes in the
sequence shown.

Table 1

ExAMPlE
MAlE
TyPE CONNECTOR
45° Flare 48
Compression 68
Polyline 1268
Selfalign 681
Air Brake (Nylon) 1468
Air Brake (Copper) 1368

Table 2
TuBE SIzE PIPE ThREADS
X2 1/8" 1/8"
X3 3/16" 1/8"
X4 1/4" 1/8"
X5 5/16" 1/8"
X6 3/8" 1/4"
X7 7/16" 1/4"
X8 1/2" 3/8"
X10 5/8" 1/2"
X12 3/4" 1/2"
X14 7/8" 3/4"
X16 1" 1"
X20 1-1/4" No Standard
X24 1-1/2" No Standard
X32 2" No Standard

Tee

ExAMPlE FEMAlE CONNECTOR
46
66
1266
661
1466
1366

Refer to safety information regarding
Application Data
proper selection of tubing and tube

Tube Connector connectors on page 1.

Selector Chart

Connector Types Mini-Barb Polyline ThreadedSleeve Pipe InvertedFlare SAE 45° Flare Compression Selfalign 1400 Series Air Brake 1300 Series Air Brake Push>Connect Q-CAB. MoldedCompression
Material Brass Brass Brass Brass Brass Brass Brass Brass Brass Brass Brass Brass Nylon Poly
Tube Size 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/4 1/4 1/8 1/8 1/8
(O.D. range in inches) 1/2 1/2 3/8 3/4 1 3/4 1 1 3/4 3/4 1/2 2 2
Maximum Working Pressure Depends on tubing material, O.D., wall thickness and connector size. 135 500 500 1200 2000 2000 2000 2000 150 150 250 150 50/220
VIBRATION (COMPARATIVE)
Fair
Good
Excellent
TuBING TyPES
Copper
Steel
Aluminum
Stainless Steel-Annealed
Stainless Steel-1/8-Hard
Polyethylene w/insert w/insert
Nylon w/insert
Polyvinyl Chloride (PVC) w/insert w/insert
Bundy B B
CONFORMS
SAE
NSF Listed
FDA Listed N
UL F F F F
ASA
ASME
Military H
DOT H
TyPICAl uSE
Instrumentation
Oil-Air-Water
Refrigeration
Hydraulic Systems
Cooling Systems
Lubrication Systems

Air Brake
Recommendation and B — May be used if bundy is tin dipped F — Available on special order H — Available in most sizes
Applicability N — Nylon material
EATON Brass Products Master Catalog E-BRFI-MC001-E3 February 2008 9

Application Data

Thread Identification
American Connections
NPTF (National Pipe This connection is still
Tapered Fuel) widely used in fluid power systems, even though it is not recommended by the National Fluid Power Association (NFPA) for use in hydraulic applications. The thread is tapered and the seal takes place by deformation of the threads.
NPTF Threads Measure thread diameter and subtract 1/4-inch to find
the nominal pipe size.
NOMINAl INCh DASh ThREAD MAlEThREAD FEMAlEThREAD SIzE SIzE SIzE O.D. INCh I.D. INCh

fraction decimal fraction decimal
1/8 02 1/8-27 13/32 0.41 3/8 0.38
1/4 04 1/4-18 17/32 0.54 1/2 0.49
3/8 06 3/8-18 11/16 0.68 5/8 0.63
1/2 08 1/2-14 27/32 0.84 25/32 0.77
3/4 12 3/4-14 1-1/16 1.05 1 0.98
1 16 1-11-1/2 1-5/16 1.32 1-1/4 1.24
1-1/4 20 11/4-11-1/2 1-21/32 1.66 1-19/32 0.58
1-1/2 24 11/2-11-1/2 1-29/32 1.90 1-13/16 1.82

2 32 2-11-1/2 2-3/8 2.38 2-5/16 2.30
This connection is some
times used in fluid power
systems. The female half
has a straight thread and an
inverted 30° seat. The male
half of the connection has
a straight thread and a 30°
internal chamfer. The seal
takes place by compression
of the 30° seat on the cham
fer. The threads hold the
connection mechanically.
NOTE: A properly chamfered
NPTF male will also seal
with the NPSM female.
NOMINAl
INCh DASh ThREAD MAlE ThREAD FEMAlE ThREAD
SIzE SIzE SIzE O.D. INCh I.D. INCh

NPSM (National Pipe Straight Mechanical)
fraction decimal fraction decimal
1/8 02 1/8-27 13/32 0.41 3/8 0.38
1/4 04 1/4-18 17/32 0.54 1/2 0.49
3/8 06 3/8-18 11/16 0.68 5/8 0.63
1/2 08 1/2-14 27/32 0.84 25/32 0.77
3/4 12 3/4-14 11/16 1.05 1 0.98
1 16 1-11-1/2 15/16 1.32 1-1/4 1.24
1-1/4 20 11/4-11-1/2 1-21/32 1.66 1-19/32 0.58
1-1/2 24 11/2-11-1/2 1-29/32 1.90 1-13/16 1.82
2 32 2-11-1/2 2-3/8 2.38 2-5/16 2.30
10 EATON Brass Products Master Catalog E-BRFI-MC001-E3 February 2008

Application Data

Thread Identification
American Connections
SAE J514 37° hydraulic

This connection is very common in fluid power systems. Both the male and female halves of the connections have 37° seats. The seal takes place by establishing a line contact between the male flare and the female cone seat.

The threads hold the con
nection mechanically.
CAUTION: In the –02, –03,
–04, –05, –08 and –10 sizes,
the threads of the SAE 45°
flare and the SAE 37° flare
are the same. However, the
sealing surface angles are
not the same.
NOMINAl
INCh DASh ThREAD MAlE ThREAD FEMAlE ThREAD
SIzE SIzE SIzE O.D. INCh I.D. INCh

fraction decimal fraction decimal
1/8 02 5/16-24 5/16 0.31 9/32 0.27
3/16 03 3/8-24 3/8 0.38 11/32 0.34
1/4 04 7/16-20 7/16 0.44 13/32 0.39
5/16 05 1/2-20 1/2 0.50 15/32 0.45
3/8 06 9/16-18 9/16 0.56 17/32 0.51
1/2 08 3/4-16 3/4 0.75 3/4 0.69
5/8 10 7/8-14 7/8 0.88 13/16 0.81
3/4 12 11/16-12 1-1/16 1.06 1 0.98
7/8 14 13/16-12 1-3/16 1.19 1-1/8 1.13
1 16 15/16-12 1-5/16 1.31 1-1/4 1.23
1-1/4 20 1-5/8-12 1-5/8 1.63 1-9/16 1.54
1-1/2 24 1-7/8-12 1-7/8 1.88 1-13/16 1.79
2 32 2-1/2-12 2-1/2 2.50 2-7/16 2.42

Application Data

Thread Identification
American Connections
SAE J512 Inverted This connection is frequently
used in automotive systems.
The male connector can
either be a 45° flare in the
tube fitting form or a 42°
seat in the machined adapt
er form. The female has a
straight thread with a 42°
inverted flare. The seal takes
place on the flared surfaces.
The threads hold the con
nection mechanically.
NOMINAl
INCh DASh ThREAD MAlE ThREAD FEMAlE ThREAD
SIzE SIzE SIzE O.D. INCh I.D. INCh
fraction decimal fraction decimal
1/8 02 5/16-24 5/16 0.32 9/32 0.28
3/16 03 3/8-24 3/8 0.38 11/32 0.34
1/4 04 7/16-24 7/16 0.44 13/32 0.40
5/16 05 1/2-20 1/2 0.50 15/32 0.45
3/8 06 5/8-18 5/8 0.63 9/16 0.57
7/16 07 11/16-18 11/16 0.69 5/8 0.63
1/2 08 3/4-18 3/4 0.75 23/32 0.70
5/8 10 7/8-18 7/8 0.88 13/16 0.82
3/4 12 11/16-16 11/16 1.06 1 1.00

Application Data

Thread Identification
American Connections SAE J512 45°

This connection is commonly used in refrigeration, automotive and truck piping systems. The connector is frequently made of brass. Both the male and female connectors have 45° seats. The seal takes place between the male flare the female cone seat. The

threads hold the connection
mechanically.
CAUTION: In the –02, –03,
–04, –05, –08 and –10 sizes,
the threads of the SAE 45°
flare and the SAE 37° flare
are the same. However, the
sealing surface angles are
not the same.
NOMINAl
INCh DASh ThREAD MAlE ThREAD FEMAlE ThREAD
SIzE SIzE SIzE O.D. INCh I.D. INCh

fraction decimal fraction decimal
1/8 02 5/16-24 5/16 0.31 9/32 0.27
3/16 03 3/8-24 3/8 0.38 11/32 0.34
1/4 04 7/16-20 7/16 0.44 13/32 0.39
5/16 05 1/2-20 1/2 0.50 15/32 0.45
3/8 06 5/8-18 5/8 0.63 9/16 0.57
1/2 08 3/4-16 3/4 0.75 11/16 0.69
5/8 10 7/8-14 7/8 0.88 13/16 0.81
3/4 12 1-1/16-14 1-1/16 1.06 1 0.99
7/8 14 1-1/4-12 1-1/4 1.25 1-5/32 1.16
1 16 1-3/8-12 1-3/8 1.38 1-9/32 1.29

Application Data

Thread Identification
British Connections
British Standard Pipe (BSP)
This BSPT (tapered) connection is similar to the NPT, except that the thread pitches are different in most
sizes, and the thread form
and O.D.s are close but not the same. Sealing is accomplished by thread distortion. A thread sealant is recommended.
The BSP (parallel) male is similar to the NPSM male except the thread pitches
are different in most sizes.
The female swivel BSPP has a tapered nose/Globeseal flareless swivel which seals on the cone seat of the male.

BSPT/BSPP Threads NOMINAl
INCh DASh ThREAD MAlEThREAD FEMAlEThREAD SIzE SIzE SIzE* O.D. INCh I.D. INCh
fraction decimal fraction decimal
1/8 02 1/8–28 3/8 0.38 11/32 0.35
1/4 04 1/4–19 33/64 0.52 15/32 0.47
3/8 06 3/8–19 21/32 0.65 19/32 0.60
1/2 08 1/2–14 13/16 0.82 3/4 0.75
5/8 10 5/8–14 7/8 0.88 13/16 0.80
3/4 12 3/4–14 11/32 1.04 31/32 0.97
1 16 1–11 15/16 1.30 1-7/32 1.22
1-1/4 20 1-1/4–11 1-21/32 1.65 1-9/16 1.56
1-1/2 24 1-1/2–11 1-7/8 1.88 1-25/32 1.79
2 32 2–11 2-11/32 2.35 2-1/4 2.26

*Frequently, the thread size is expressed as a fractional dimension preceded by the letter “G” or the letter “R”.
The “G” represents a parallel thread and the “R” indicates a tapered thread.
For example, BSPP 3/8–19 may be expressed as G 3/8, and BSPT 3/8–19 may be expressed as R3/8.

Application Data

Tubing Selection

Selection To select tubing for a particular installation, two factors must be determined…
Tubing Types
1. Tubing Type:
material and construction
2. Size:
Inside diameter (I.D.) and wall thickness. Information listed below will aid in your tubing selection. Commercial tubing is available in a wide variety of materials, types of construction and quality. Each is best suited for certain specific applications.
Aluminum Tubing
Seamless annealed is approved by SAE for low pressure applications.
Copper Tubing:
Seamless fully annealed coils and fully annealed or quarter-hard straight lengths can be used for systems that do not use petroleum based fluids (copper acts as an oil-oxidation catalyst, causing sludge). Copper also tends to work harden when flared or bent and has poor resistance to vibration. Therefore, the use of copper tubing is limited to low-pressure stationary applications and air circuits.
Special Alloy Tubing:
May be required for specific corrosion problems. Information on these applications can be obtained from your tubing supplier or from tubing manufacturers.
Tubing Size

The two variables in tubing
size are the inside diameter
(ID) and the wall thickness. Each of these is dependent upon a number of factors.
Inside Diameter –
The tubing I.D. will determine the flow and velocity of the fluid in the system.
Flow is the volume of fluid that is to be moved through the line to perform a given job within a specified time. Flow rate is expressed in gallons per minute (gpm).
Velocity is the rate of speed at which the fluid passes through the line. It is expressed in feet per second (fps). With a given flow rate, the velocity will increase as the inside diameter of the tubing decreases.
Note:

To determine the appropriate tubing I.D. for specific flow rate and velocity, refer to the Velocity vs. Flow chart on page 17.

Refer to safety information regarding
proper selection of tubing and tube fittings on page 1.

Wall Thickness
The required wall thickness of the tubing depends upon operating pressure, safety factor, temperatures, and tubing material.
Operating Pressure is the pressure of the fluid in the system. It is expressed in pounds per square inch (psi).
Safety Factor is a multiplier applied to the wall thickness that compensates for additional mechanical strains and hydraulic shocks to which the tubing may be subjected during operation.
Note:
To determine the appropriate wall thickness, refer to the data on page 16 .
Pressure Drop
Total pressure supplied to a line must equal usable pressure (or output) plus the pressure that is lost through fluid transmission, which is referred to as pressure drop. These pressure drops cause loss of energy and should be kept to a minimum. Elements which cause pressure drop in the transmission of fluids include sudden enlargements or contractions, bends, fittings and valves.
Mathematical analysis of pressure drop, although possible, is not precise because of the interrelationship of factors such as fluid velocity, density, flow area and friction coefficients. Therefore, to obtain optimum efficiency, the system (or the questionable portions of the system) should be mocked-up to obtain empirical pressure drop data.

Refer to safety information regarding
Application Data
proper selection of tubing and tube

Tubing Selection
Problem
Solution
Standard Size hydraulic Tubing
Following is a typical problem that illustrates, step by step, the procedure for determin
ing tube size.
Select Bundyweld tubing with the appropriate I.D. and wall thickness for the following conditions:
1. Using the Flow/Velocity chart on Page 17, follow
the horizontal flow line
(5 gpm) until it intersects the vertical velocity line (10fps). From this point, follow the diagonal line upward to get the required tube I.D. (.444).
If the horizontal flow line
and the vertical velocity line intersect between two diagonal lines, normally the larger inside diameter would be selected since it would mean less velocity.
2. Refer to the chart of
Standard Size Hydraulic
Tubing, below. Note that .444 I.D. tubing is not listed. If you want to use standard tubing, select one with a larger I.D. Do
not select a smaller size
Flow –– 5 gpm Velocity –– not to exceed 10
fps Pressure — 2000 psi Safety Factor –– 4:1

since this would increase the velocity to over the 10 fps limit. Therefore, by going to the next largest
size, you would select the
5/8” O.D. tubing having an I.D. of .459 and a wall thickness of .083.
3. To determine whether this tubing will meet the pressure and safety factor requirements, refer to the Recommended Wall Thickness data on page
18. For 5/8” O.D. tubing at 2000 psi, the chart for Bundyweld indicates that the minimum wall thickness with a safety factor of 4:1 is .05952. Since you have selected a tubing with a .083 wall, this would easily fulfill the requirements. However,
connectors on page 1.
for savings on weight and cost, you can select another tubing with a thinner wall that will still meet the performance requirements. Therefore, refer again to the chart
on standard size tubing
and select a tubing with a wall thickness closer to the minimum requirements. This would be the 5/8” O.D. tubing with a .509 I.D. and a .058 wall. This tubing will handle the pressure requirements of 2000 psi with a safety factor of 4:1, and also provides the required flow while keeping the velocity within the 10 fps limitation.
TuBE TuBE TuBE TuBE TuBE TuBE TuBE TuBE TuBE TuBE TuBE TuBE
O.D. I.D. WAll O.D. I.D. WAll O.D. I.D. WAll O.D. I.D. WAll
1/8” .055 .061 .035 .032 3/8” .245 .259 .065 .058 5/8” .435 .459 .095 .083 7/8” .657 .685 .109 .095
.065 .030 .277 .049 .481 .072 .709 .083
.069 .028 .291 .305 .042 .035 .495 .509 .065 .058 .731 .745 .072 .065
3/16” .117 .035
.123 .032 .311 .032 .527 .541 .049 .042 .759 .777 .058 .049
.127 .030 1/2” .310 .095
1/4” .120 .065 .334 .083 .555 .035 1” .760 .782 .120 .109
.134 .058 .358 .072 3/4” .532 .109
.152 .049 .370 .065 .560 .095 .810 .834 .095 .083
.166 .042 .384 .058 3/4” .584 .083
.180 .035 .402 .049 .606 .072 .856 .072
.190 .030 .416 .430 .436 .042 .035 .032 .620 .634 .652 .065 .058 .049 .870 .884 .902 .065 .058 .049
5/16” .182 .196 .065 .058
.214 .049 .680 .035
.228 .042
.242 .035
.248 .032

Application Data

Tubing Selection
Flow/Velocity Chart

To Find Required Tube I.D.
Flow–20 gpm Velocity–9 fps
Follow horizontal flow line
(20 gpm) until it intersects vertical velocity line (9 fps). From this point follow diagonal line to get required Tube
I.D. –(.944).
To Find Permissible Flow
Velocity–15 fps Tube I.D.–.495
Follow vertical velocity line (15 fps) until it intersects diagonal line representing .495 tube I.D. Then project
this point horizontally to get
the permissible flow–(9 gpm).
To Find Velocity of Fluid in System
Flow–6 gpm Tube I.D.–.694
Follow horizontal flow line

(6 gpm) until it intersects diagonal line representing .694 tube I.D. Then project this point vertically downward to get the velocity of fluid –(5 fps).

Refer to safety information regarding
Application Data
proper selection of tubing and tube Tubing Selection connectors on page 1.
With the following Recommended Wall Thickness Bundyweld
Recommended Wall TEMPERATuRE COPPER AluMINuM Based on 42,000#/IN.2 Strength (F S=4)

Thickness tables the tubing wall can be selected that is best suited for a particular application. The data given in these tables are raw figures based on the equation:
t= Dp(FS)

2S t – wall thickness (inches) D – O.D. of tube (inches) p – pressure (psi) FS– Safety Factor S – tensile strength of
tubing material

Therefore, many of the wall thicknesses given in these tables are not found on standard tubing, but serve to establish the minimum wall required.
Safety Factor
The standard safety factors indicate three grades of severity of service:
4:1 – mechanical and hydraulic shocks not excessive
6:1 – considerable
TuBE WORkING PRESSuRE (PSI)
+100F. 1.00 1.00 O.D. 1,000 2,000 3,000 4,000 5,000
+200F. 1.08 1.00 1/8 +300F. 1.22 1.08 3/16 +400F. 2.30 1.41 1/4 +500F. – 2.10 5/16 +600F. – – 3/8 +700F. – – 1/2+800F. – – 5/8+900F. – –
+1000F. – –

Aluminum 3003 (H-14) Based on 20,000#/IN.2, Strength (F.S. –4) Aluminum 5052 (H-32) Based on 31,000#/IN.2, Strength (F.S. –4)
TuBE O.D. WORkING PRESSuRE (PSI) 1,000 2,000 3,000 4,000 5,000 WORkING PRESSuRE (PSI) 1,000 2,000 3,000 4,000 5,000
1/8 .01250 .02500 .3750 .05000 .00806 .01613 .02419 .03226 .04032
3/16 .01875 .03750 .05650 .07500 .01210 .02419 .03629 .04839 .06048
1/4 .02500 .05000 .07500 .10000 .01613 .03226 .04839 .06452 .08065
5/16 .03125 .06250 .09375 .12500 .02016 .04032 .06048 .08065 .10081
3/8 .03750 .07500 .11250 .15000 .02419 .04839 .07258 .09677 .12097
1/2 .05000 .10000 .15000 .20000 .03227 .06452 .09677 .12903 .16129
5/8 .06250 .12500 .18750 .25000 .04032 .08065 .12097 .16129 .20161
3/4 .07500 .15000 .22500 .30000 .04839 .09677 .14516 .19355 .24194
7/8 .08750 .17500 .26250 .35000 .05645 .11290 .16935 .22581 .28226
1 .10000 .20000 .30000 .40000 .06452 .12903 .19355 .25806 .32258
1-1/4 .12500 .25000 .37500 .50000 .08065 .16129 .24194 .32258 .40323
1-1/2 .15000 .30000 .45000 .60000 .09677 .19355 .29032 .38710 .48387
2 .20000 .40000 .60000 .80000 .12903 .25806 .38710 .51613 .64516

mechanical strain and hydraulic shock

8:1 – hazardous applications
with severe service conditions

The wall thickness shown in these tables are based on ultimate strength of material and a safety factor of 4:1.
To obtain the recommended wall for a specific pressure based on a safety factor of 6:1, multiply the wall thickness indicated in the table by 1.5. For a safety factor of 8:1, multiply by 2
Temperature
The wall thickness found by using these tables can be corrected for temperature by multiplying the wall thickness by the appropriate correction factor given in the chart below. The table is based on strength reduction due to increased temperature.
Annealed Copper Based on 30,000#/IN.2, Strength (F.S. –4) Copper (UNS C12200 Light Drawn) Based on 40,000#/IN.2, Strength (F.S. –4)
TuBE O.D. WORkING PRESSuRE (PSI) 1,000 2,000 3,000 4,000 5,000 WORkING PRESSuRE (PSI) 1,000 2,000 3,000 4,000 5,000
1/8 .00833 .01667 .02500 .03333 .04167 .00625 .01250 .01875 .02500 .03125
3/16 .01250 .02499 .03750 .04999 .06250 .00938 .01875 .02812 .03750 .04688
1/4 .01667 .03333 .05000 .06666 .08333 .01250 .02500 .03750 .05000 .06250
5\16 .02083 .04167 .06250 .08333 .10417 .01562 .03125 .04688 .06250 .07812
3\8 .02499 .04999 .07500 .09999 .12499 .01875 .03750 .05625 .07500 .09375
1\2 .03333 .06667 .10000 .13333 .16667 .02500 .05000 .07500 .10000 .12500
5\8 .04167 .08333 .12500 .16666 .20883 .03125 .06250 .09375 .12500 .15625
3\4 .04999 .09999 .15000 .19999 .24999 .03750 .07500 .11250 .15000 .18750
7/8 .05833 .11667 .17500 .23333 .29166 .04375 .08750 .13125 .17500 .21875
1 .06667 .13333 .20000 .26666 .33333 .05000 .10000 .15000 .20000 .25000
1-1/4 .08333 .16667 .25000 .33333 .41667 .06250 .12500 .18750 .25000 .31250
1-1/2 .09999 .19999 .30000 .39999 .49999 .07500 .15000 .22500 .30000 .37500
2 .13333 .26667 .40000 .53333 .66667 .10000 .20000 .30000 .40000 .50000

Shaded Areas

Tubing wall thickness listed in the shaded areas are generally either too light or too heavy for practical applications, and are listed only to provide data for accurate computation.
Application Data
Flare Dimensions
JIC 37° MAxIMuM
FlARE TuBES TuBE SINGlE FlARE DOuBlE FlARE R WAll ThICkNESS SINGlE DOuBlE
SIzE A DIAMETER B DIAMETER RADIuS FlARE FlARE
(SAE J533) O.D. MAx. MIN. MAx. MIN. ±.020 D D
1/8 0.200 0.180 0.200 0.180 0.030 0.035 0.025
3/16 0.280 0.260 0.280 0.260 0.030 0.035 0.028
1/4 0.360 0.340 0.360 0.340 0.030 0.065 0.035
5/16 0.430 0.400 0.430 0.400 0.030 0.065 0.035
3/8 0.490 0.460 0.490 0.460 0.040 0.065 0.049
1/2 0.660 0.630 0.660 0.630 0.060 0.083 0.049
5/8 0.790 0.760 0.790 0.760 0.060 0.083 0.049
3/4 0.950 0.920 0.960 0.920 0.080 0.109 0.049
7/8 1.070 1.040 1.070 1.040 0.080 0.109 0.065
1 1.200 1.170 1.200 1.170 0.090 0.120 0.065
1 1/4 1.510 1.480 1.510 1.480 0.090 0.120 0.065
1 1/2 1.730 1.700 1.730 1.700 0.110 0.120 0.065
2 2.360 2.330 2.360 2.330 0.110 0.134 0.065

Application Data
Flare Dimensions
SAE 45° DOuBlE MAxIMuM
FlARETuBES SINGlE FlARE SINGlE FlARE COINED FlARE WAll ThICkNESS SINGlE DOuBlE
(SAE J533) TuBE SIzE A DIAMETER MAx. MIN B DIAMETER MAx MIN SEAT lENGTh C FlARE D FlARE D1
1/8 0.171 0.181 0.198/ 0.213 0.040 0.035 0.025
3/16 0.239/ 0.249 0.265/ 0.280 0.040 0.035 0.028
1/4 0.315/ 0.325 0.345/ 0.360 0.040 0.049 0.035
5/16 0.388/ 0.404 0.410/ 0.425 0.062 0.049 0.035
3/8 0.471/ 0.487 0.485/ 0.500 0.062 0.065 0.049
7/16 0.545/ 0.561 0.555/ 0.570 0.062 0.065 0.049
1/2 0.607/ 0.623 0.625/ 0.640 0.062 0.083 0.049
9/16 0.660/ 0.676 0.697/ 0.712 0.062 0.083 0.049
5/8 0.732/ 0.748 0.757/ 0.772 0.062 0.095 0.049
3/4 0.900/ 0.916 0.897/ 0.912 0.062 0.109 0.049
7/8 1.025/ 1.041 –– – 0.109 –
1 1.141/ 1.157 –– – 0.120 –

Application Data

Tubing Installation
Right

Figure 1
Nearly all industrial equipment now in service makes some use of fluid lines. From an economic point of view, the best fluid lines system is that which is easiest to maintain at the lowest original cost. The use of tubing and tube connectors on lines up to 2” diameter is usually more economical than the use of pipe and pipe connectors in modern installations. A few of the more important reasons follow:
1. Size for size, tubing is
lighter weight, easier to handle and can be bent more easily than iron pipe.
2.
Ductile hydraulic tubing reduces the number of connections required, thus reducing material and labor costs. Bent tubing also reduces pressure drop and turbulence in the system.

3.
Fewer joints means lower costs and fewer points of potential leakage.

4.
The use of tube connectors makes every joint a union, permitting easier, faster maintenance and repair work.

5.
Modern flared and flare-less tube fittings eliminate the need for threading, soldering, or welding.

Figure 2
Right

Tube Bending
Tubing should be bent wherever possible to reduce the number of connectors.
Copper tubing can be bent easily with a hand bender. Steel tubing can be bent
in sizes 1/8” to 5/8” O.D.
by using a hand bender designed for steel tubing. For production quantities,
or for sizes larger than 5/8”
O.D., a power bender is generally used.
Tubing should be bent accurately. Tubing manufacturers will advise the correct radii for various types and wall thicknesses of tubing. Kinks, flattened bends, wrinkles and tube breakage or loss should be avoided by the use of proper tube bending equipment.
Precautions
Avoid straight line connections wherever possible, especially in short runs.
Design piping systems symmetrically. They are easier to install and present a neat appearance.
Right

Wrong

Figure 3
Care should be taken to eliminate stress from tubing lines. Long tubing runs should be supported by brackets or clips. All parts installed on tubing lines such as heavy fittings, valves, etc., should be bolted down to eliminate tubing fatigue.
Before installing tubing, inspect the tube to see that it conforms to the required specifications, is of the correct diameter and wall thickness and is not out of round.
Cut tube ends reasonably square and lightly deburr inside and outside edge. Chamfer on outside edge will destroy bearing of tube end on the connector seat.
To avoid difficulty in assembly and disconnecting, a sufficient straight length of tube must be allowed from the end of the tube to the start of the bend. Allow twice the length of the nut as a minimum.

Note:
Springing the tubing to force alignment places strain on fitting joints.
Tubes should be formed to assemble with true alignment to the center line of the fittings, without distortion or tension. Tubing which has to be sprung from position, “A”, (see Fig. 4), to be inserted into the connector has not been properly fabricated, and when so installed and connected, places the tubing under stress.
When assembling the tubing, insert the longer leg to the connector as at “C” (Fig. 4). With the nut free, the short leg of the tubing can be easily moved and brought to proper position with and inserted into the seat in connector “D”. The nuts can then be tightened as required.
Application Data

Chemical Compatibility Chart
These tables alphabetically bearing upon the suitability list commonly used materi-of any tubing or connector als of various chemical com-for any specific application, position. After each agent and these factors must be listing you will find the basic considered by you as you tubing and connector materi-review the chemical compatals rated according to their ibility chart. chemical resistance to each Where unusual conditions individual agent. The chart exist or where questions
is intended to be used as arise, consult Eaton for expert
a guide only. Many factors assistance on your tubing (concentration, temperature, application requirements. intermittent or continuous exposure, etc.) have a
NylON 11

Refer to safety information regarding
proper selection of tubing and tube connectors on page 1.
Note:
All data given herein is believed to be accurate and reliable but presented without guarantee, warranty, or responsibility of any kind, express or implied, on our part. Chemical resistance will vary with the wide diversity of possible mixtures and service conditions. It is not therefore possible to give any guarantee whatsoever in individual cases.
TP160 NylON 6/6 PVC FluID NT100 PT230 PT200 POlyEThylENE PT240 (lDPE) BRASS
Acetaldehyde G F X X G
Acetic Acid (Concentrated) X X X X X
Acetic Acid (Dilute) F X F G X
Acetic Anhydride X X X X X
Acetone G F X G G
Acrylonitrile G — G — —
Air G G G G G
Alcohols
Amyl Alcohol G G X G G
Butyl Alcohol, Butanol G G X G G
Ethyl Alcohol, Ethanol G G F G G
Isopropyl Alcohol, Isopropanol G G G G G
Methyl Alcohol, Methanol G G X G G
Aluminum Chloride X X G G X
Aluminum Fluoride X X G G X
Aluminum Hydroxide G G G G X
Aluminum Nitrate G F G G X
Aluminum Sulfate G F G G X
Alums F G G G X
Ammonia, Anhydrous Use approved anhydrous ammonia hose X
Ammonia Solution (10%) G X G G X
Ammonium Chloride X X G G X
Ammonium Hydroxide G X X G X
Ammonium Nitrate G G G G X
Ammonium Phosphate G G F G X
Ammonium Sulfate G G G G X
Amyl Acetate G G X X G
Amyl Alcohol G G X G G
Aniline X X X X X
Aniline Dyes X X X X X
Animal Oils and Fats G — G X G
Anti-Freeze (Glycol Base) G — G F G
Aqua Regia X X X X —
Aromatic Hydrocarbons G G X G G
Asphalt Emulsion G — X — G
Barium Chloride G — G G G
Barium Hydroxide G G G G X
Codes: Barium Sulfate G G G G G
G = Good Resistance Barium Sulfide X — G G X
F = Fair Resistance Beet Sugar Liquors G G G G X
X = Incompatible Benzaldehyde G G X X F
– = No data available Benzene, Benzol G G X X G
+ = Call Technical Support for specific application Benzoic Acid X X X Black Sulfate Liquor X X X G G G X
Bleach Solution X X F G X
22 EATON Brass Products Master Catalog E-BRFI-MC001-E3 February 2008

Application Data Refer to safety information regarding proper selection of tubing and tube
Chemical connectors on page 1.
Compatibility
Chart
FluID NylON 11 TP160 NT100 NylON 6/6 PVC PT230 PT200 POlyEThylENE PT240 (lDPE) BRASS
Borax Solution G — G G G
Boric Acid G G G G G
Brake Fluid (Glycol Ether Base) G — X X G
Brine G — G G G
Bromine X X X X X
Butane Use Butane approved hose
Butyl Acetate G — X X G
Butyl Alcohol, Butanol G G X G G
Calcium Bisulfite G X G G X
Calcium Chloride G X G G X
Calcium Hydroxide G G G G G
Calcium Hypochlorite X X G G G
Cane Sugar Liquors G G G G
Carbon Dioxide (Dry) G G G G G
Carbon Dioxide (Wet) G G G G F
Carbon Disulfide (Bisulfide) X X X X G
Carbon Monoxide (Hot) X X X X G
Carbon Tetrachloride G G X X G
Carbonic Acid G — G G X
Castor Oil G — G X G
Cellosolve Acetate G — X — X
Chlorinated Solvents F G X X G
Chloroacetic Acid X X X X X
Chlorobenzene X X X X F
Chlorine Gas (Dry) X X X X G
Chlorine Gas (Wet) X X X X X
Chloroform F G X X G
Chlorosulfonic Acid X X X X X
Chromic Acid (under 25%) X X F F X
Chromic Acid (over 25%) X X X X X
Citric Acid X F G G X
Coke Oven Gas G — X G F
Copper Chloride X X G G X
Copper Cyanide G G G G X
Copper Sulfate G G G G X
Corn Syrup (Non-food) G — G G —
Cottonseed Oil G — F G G
Creosote X X X X F
Cresol X X X X —
Cyclohexanol G G X F G
Dextrose (Food Grade) X X X G —
Dichlorobenzene G — X X —
Diesel Fuel G — X X G
Diethanolamine G — X — X
Diethylenetriamine X X X G —
Dowtherm A X X X X X
Enamel (Solvent Base) G — X G G
Ethanolamine G — X G X
Ethers (Ethyl Ether) G — X X G
Ethyl Alcohol G G F G G
Ethyl Acetate G G X G G

Codes: Ethyl Acrylate X — X — — Ethyl Methacrylate X — X — —
G = Good Resistance F = Fair Resistance Ethylamine X X X G G
X = Incompatible Ethyl Cellulose F — X G G
– = No data available Ethyl Chloride G — X X G
+ = Call Technical Support Ethylenediamine X X X G G for specific application
Ethylene Dibromide F — X — —
Ethylene Dichloride F — X X F

Refer to safety information regarding
Application Data
proper selection of tubing and tube Chemical connectors on page 1.

Compatibility Chart
NylON 11 TP160 NylON 6/6 PVC POlyEThylENE FluID NT100 PT230 PT200 PT240 (lDPE) BRASS
Ethylene Glycol G G G G G
Ethylene Oxide G — X X X
Fatty Acids G G G G F
Ferric Chloride 5% G G G G X
Ferric Sulfate G G G G X
Fertilizer Salts Solution F — G G —
Formaldehyde G G X G G
Formic Acid X X X G F
Freon 12 Use approved Freon 12 hose G
Freon 134a Use approved Freon 134a hose —
Fuel Oil G —F X G
Furfural X XX X G
Gasoline (Refined) G G X X G
Gasoline (Unleaded) G G X X G
Gasoline (10% Ethanol) G G X X G
Gasoline (10% Methanol) G G X X G
Glucose (non-food) G G G G G
Glycerine, Glycerol (Non-food) G G G G G
Greases G GG G G
Green Sulfate Liquor X X G G X
Heptane G GX X G
Hexane GGX X G
Houghto Safe 273 to 640 G — F G G
Houghto Safe 5046, 5047F G — G G G
Houghto Safe 1000 Series G — X X G
Hydraulic Oils
Straight Petroleum Base G G G G G
Water Petroleum Emulsion G — — F G
Water Glycol G G X — G
Straight Phosphate Ester G G X X G
Phos. Ester/Petroleum Blend G G X X G
Polyol Ester G — — — G
Hydrobromic Acid (under 48%) X X G G X
Hydrochloric Acid X X G G X
Hydrocyanic Acid X X G G G
Hydrofluoric Acid (under 50%) X X F F X
Hydrofluoric Acid (over 50%) X X X X X
Hydrofluosilicic Acid X X G G X
Hydrogen Use approved hydrogen hose or metal tubing G
Hydrogen Peroxide X X — G X
Hydrogen Sulfide X X G G G
Hydrolube G —G G G
Iodine XXX X X
Isocyanates X X X X —
Isopropyl Alcohol, Isopropanol G G G G G
Isopropylamine X — X — G
Iso-Octane G G X X G
Jet Fuel (Transfer Only) G G X X G
Kerosene G GX X G
Lacquer G GX F G
Lacquer Solvents G G X F G
Lactic Acid G G G G F
Codes:
Lime Sulfur G F G G X G = Good Resistance Lindol GG— — FF = Fair Resistance
X = Incompatible Linseed Oil G G G G G
– = No data available Lubricating Oils G G G G G
+ = Call Technical Support Lye GFG GF
for specific application Magnesium Chloride G G G G F
Magnesium Hydroxide G G G G G
Application Data Refer to safety information regarding proper selection of tubing and tube
Chemical connectors on page 1.
Compatibility
Chart
NylON 11 TP160 NylON 6/6 PVC FluID NT100 PT230 PT200 POlyEThylENE PT240 (lDPE) BRASS
Magnesium Sulfate G G G G G
Mercuric Chloride X X F G X
Mercury G G F G X
Methyl Alcohol, Methanol G G X G G
Methyl Acrylate X X X — G
Methyl Bromide G F X X G
Methyl Chloride G G X X G
Methylene Chloride F F X X G
Methyl t-Butyl Ether (MTBE) G G X — —
Methyl Ethyl Ketone G G X G G
Methyl Isobutyl Ketone G G X G G
Methyl Isopropyl Ketone G G X G G
Methyl Methacrylate X — X — —
Mineral Oil G G F X G
Mineral Spirits G G X G G
Naphtha G G X G —
Napthalene G G X X G
Nickel Acetate G G G G F
Nickel Chloride G G G G X
Nickel Sulfate G G G G G
Nitric Acid (under 35%) X X G F X
Nitric Acid (35% to 60%) X X F X X
Nitric Acid (over 60%) X X X X X
Nitrobenzene X — X X G
Nitrogen Gas G G G G G
Nitrous Oxide F F X X G
Oleic Acid G G F G G
Oleum (Fuming Sulfuric Acid) X X X X X
Oxalic Acid X X G G F
Oxygen (non-breathing,non-welding) + G G G G G
Ozone (300 pphm) X X X X —
Paint (Solvent Base) G G X F G
Palmitic Acid G G F G X
Paper Mill Liquors X X X X —
Pentane G — X X G
Perchloroethylene F G X X G
Petroleum Ether G G X X G
Petroleum Oils G G G G G
Phenol X X X X G
Phosphoric Acid (to 85%) X X G G G
Picric Acid (Molten) X X X X X
Picric Acid (Solution) X X X X X
Potassium Chloride G G G G F
Potassium Cyanide G G G G X
Potassium Dichromate F — G G F
Potassium Hydroxide G F G G F
Potassium Permanganate X X G G —
Potassium Sulfate G G G G F
Propane Liquid Use hose approved for Propane Liquid G
Propylene Glycol G — F G F
Pyridine X X X G F
Codes: Sea Water G G G G G
G = Good Resistance F = Fair Resistance Silver Nitrate G G G Skydrol G G X G X X G
X = Incompatible Soap Solution G G G X G
– = No data available Sodium Bicarbonate G G G G G
+ = Call Technical Support Sodium Bisulfate G G G G F
for specific application Sodium Bisulfite G G G G F

Application Data Refer to safety information regarding proper selection of tubing and tube
Chemical connectors on page 1.
Compatibility
Chart
FluID NylON 11 TP160 NT100 NylON 6/6 PT230 PVC PT200 POlyEThylENE PT240 (lDPE) BRASS
Sodium Borate G G G G G
Sodium Carbonate G G G G G
Sodium Chloride G G G G X
Sodium Cyanide G G G G X
Sodium Hydroxide G F G G F
Sodium Hypochlorite X X G G X
Sodium Nitrate G G G G F
Sodium Perborate G F G G X
Sodium Peroxide X X X X X
Sodium Phosphates G G G G G
Sodium Silicate G G G G G
Sodium Sulfate G G G G G
Sodium Sulfide G G G G X
Sodium Thiosulfate G G G G X
Soybean Oil G — F G G
Stannic Chloride F X G G X
Steam 450° F X X X X F
Stearic Acid G G F G X
Stoddard Solvent G G X X G
Styrene G G X X G
Sulfur 70o F G G F G X
Sulfur 200o F X X X X X
Sulfur Chloride X X X G X
Sulfur Dioxide X X X X G
Sulfuric Acid (under 50%) X X G G X
Sulfuric Acid (51% to 70%) X X G X X
Sulfuric Acid (71% to 95%) X X X X X
Sulfuric Acid (96% to 98%) X X X X X
Tannic Acid X X G G G
Tar G G X X G
Tartaric Acid G G G G F
Tetrachloroethane F — X F —
Tetrahydrofuran (THF) G — X X —
Toluene G G X G G
Transmission Oil (Petrol. Base) G G G G G
Trichloroethane F G X G G
Trichloroethylene F G X G G
Tung Oil G — — — G
Turpentine G G X G G
Urea (Water Solution) G G G G —
Uric Acid G G G G —
Varnish G G X G G
Vegetable Oil (Non-food) G G F G G
Vinegar G X G G X
Vinyl Acetate G — X — F
Water (non-potable) G G G G G
Water-Glycol Mixture G G X — G
Water-Petroleum Mixture G G — F G
Xylene G G X G G
Zinc Chloride X X G G X
Zinc Sulfate Codes: G G G G X

G = Good Resistance F = Fair Resistance X = Incompatible
– = No data available
+ = Call Technical Support for specific application
26 EATON Brass Products Master Catalog E-BRFI-MC001-E3 February 2008

Tubing
Plastic Tubing
NT100 “Nylon 11”
SAE J844 Type A & B DOT FMVSS 571.106
Note:
For plastic tube cutter, see page 138.

Part Number Key:
NT10006RD-100

Catalog Color Coil
Number Length

Note:
Not all colors available in all
sizes. Refer to price pages
for availability.
Connectors:
1800 Series Q-CAB pgs. 76-83
1400 Series Air Brake pgs. 84-89
For 1/8” Tubing use SelfAlign pgs. 47-52
SelfAlign connectors are not designed to meet DOT standards.
Typical Application:

Air brake systems except where temperatures exceed +200°F or where battery acid can drip on tubing.
Construction

Core, Nylon; Braid, Polyamide
fiber, (3/8" and larger sizes
only); Jacket, Nylon.
Temperature Range:
-40°F to +200°F (-40°C to +93°C)
Contains: Ultra-Violet
Stabilizer in all colors.

CATAlOG TuBE TuBE NuMBER O.D. (IN) WAll (IN)
Available Colors:

Black (BK), red (RD), blue (BU), brown (BR), silver (SL), green (GN), yellow (YW), orange (OR) and white (WH). Refer to current price list for availability of colors.
Note:

1/8", 5/32", 3/16", 1/4" and 5/16", are SAE J844 Type A (not reinforced);
3/8", 1/2", 5/8" and 3/4" are SAE J844 Type B (reinforced).
MAx. WORk. MIN. BuRST MIN. BEND lBS. PER COIl
PRES. PSI 75° PRES. PSI 75° RADIuS 70° F 100 FT. lENGTh(S) (FT)

NT10002* 1/8 (.125) .023 150 1,000 .33” 0.4 100,500,1000
NT10025* 5/32 (.156) .032 150 1,000 .41” 0.4 100,1000
NT10003 3/16 (.187) .035 150 1,000 .71” 0.6 1000
NT10004 1/4 (.250) .040 150 1,200 1.19” 1.2 100,500,1000
NT10005 5/16 (.312) .040 150 1,000 1.25” 1.8 100,500,1000
NT10006 3/8 (.375) .050 150 1,000 1.5” 2.9 100,500,1000
NT10008 1/2 (.500) .040 150 1,000 2.0” 3.8 100,500,1000
NT10010 5/8 (.625) .092 150 900 2.5” 6.8 100,250
NT10012 3/4 (.750) .092 150 800 3.0” 8.4 100,250

*Insert not required. Does not meet DOT standards.
PT200 Polyvinyl Chloride

Typical Application: Temperature Range:
Soft, pliable, plasticized PVC -5°F to +105°F Resin Tubing, for practically (-20°C to +41°C) any low pressure laboratory, Available Colors: industrial, agricultural or Clear (suffix NA) domestic application.
CATAlOG TuBE TuBE MAx. WORk. MIN. BuRST NuMBER O.D. (IN) WAll (IN) PRES. PSI 75° PRES. PSI 75°
Connectors:
Polyline pgs. 53-56
SelfAlign pgs. 47-52 with 2030x insert
Compression pgs. 41-46 with 2030x insert
Molded Compression pgs. 126-134

MIN. BEND lBS. PER COIl
RADIuS 70° F 100 FT. lENGTh(S) (FT)

PT20004 1/4 (.250) .062 65 195 1.0” 2.00 100
PT20044 1/4 (.250) .040 55 165 1.0” 2.00 100
PT20005 5/16 (.312) .062 55 165 1.25” 2.60 100
PT20006 3/8 (.375) .062 55 165 1.5” 3.30 100
PT20008 1/2 (.500) .062 45 135 2.0” 4.60 100
PT20010 5/8 (.625) .062 30 90 2.5” 5.90 100
PT20012 3/4 (.750) .094 40 120 3.0” 10.3 100
PT20016 1(1.00) .125 35 105 4.0” 18.5 100

Tubing Note: Part Number Key:
For plastic tube cutter, NT10006RD-100 Plastic Tubing see page 138.

Catalog Color Coil Number Length
PT230 Polyamide “Nylon 6/6”

Natural off-white compound covered under 21CFR177.1500 regulations for food contact.
Typical Application: Semirigid general purpose tubing.
Temperature Range:
-40°F to +180°F (-40°C to +82°C)
CATAlOG TuBE TuBE NuMBER O.D. (IN) WAll (IN)
Available Colors: Connectors:
Natural off-white (NA) and SelfAlign pgs. 47-52
black (BK). FDA colors avail-
able on request. Compression pgs. 41-46

Contains: Push>Connect pgs. 57-67
Ultra-Violet Stabilizer in Push>Connect Flow
black tubing. Controls pgs. 58, 68-69

Push>Connect Plus pgs. 69-71
MAx. WORk. MIN. BuRST MIN. BEND lBS. PER COIl
PRES. PSI 70° PRES. PSI 70° RADIuS 70° F 100 FT. lENGTh(S) (FT)

PT23002 1/8 (.125) .015 300 1,000 0.75” 0.3 100, 1,000
PT23003 3/16 (.188) .023 300 1,000 1.25” 0.6 100, 1,000
PT23004 1/4 (.250) .030 300 1,000 1.50” 1.0 100, 1,000
PT23005 5/16 (.312) .036 300 1,000 2.00” 1.5-1.6 100, 1,000
PT23006 3/8 (.375) .040 300 1,000 2.25” 2.1 100, 1,000

PT240 Polyethylene

Meets FDA for food contact. Natural off-white compound covered under 21CFR177.1520 regulations for food contact.
Typical Application:
Economical, flexible, low density Polyethylene has a wide range of uses in industrial and agricultural applications.
Temperature Range:
-40°F to +135°F (-40°C to +57°C)
CATAlOG TuBE TuBE NuMBER O.D. (IN) WAll (IN)
Available Colors:
Natural off-white (NA), black (BK), yellow (YW), orange (OR), blue (BU), red (RD), green (GN). FDA colors available on request. Refer to current price list for availability of colors.
Contains:
Ultra-Violet Stabilizer in
black tubing.
Connectors:
Minibarb. pgs. 72-75 Polyline pgs. 53-56 Selfalign pgs. 47-52
with 2030 insert
Compression pgs. 41-46 with 2030 insert Push>Connect pgs. 57-67 Push>Connect Flow
Controls pgs. 58, 68-69
Push>Connect Plus pgs. 69-71 Molded Compression
pgs. 126-134
MAx. WORk. MIN. BuRST MIN. BEND lBS. PER COIl
PRES. PSI 70° PRES. PSI 70° RADIuS 70° F 100 FT. lENGTh(S) (FT)

PT24004 1/4 (.250) .062 200 600 0.75” 1.50 100, 1,000
PT24044 1/4 (.250) .040 133 400 0.62” 1.00 100, 1,000
PT24005 5/16 (.312) .062 135 480 1.00” 1.90 100, 1,000
PT24006 3/8 (.375) .062 135 400 1.50” 2.40 100, 1,000
PT24008 1/2 (.500) .062 100 300 2.00” 3.40 100, 500
PT24010 5/8 (.625) .062 80 240 2.50” 4.40 100
PT24012 3/4 (.750) .094 70 210 3.00” 7.60 100
PT24016 1 (1.000) .125 100 300 5.00” 13.4 100

Tubing

Plastic Tubing
Note:

For plastic tube cutter, see page 138.
TP160 Polyamide “Nylon 11”

Typical Application:
Flexible nylon tubing. Used for instrumentation; lubrication and air lines; gas, chemical and oil processing; low pressure hydraulics.
Temperature Range:
-40°F to +200°F (-40°C to +93°C)
CATAlOG TuBE TuBE NuMBER O.D. (IN) WAll (IN)

Available Colors:
Black (BK) or natural (NA).
Contains:
Ultra-Violet Stabilizer
Connectors:
SelfAlign pgs. 47-52
Compression pgs. 41-46
MAx. WORk. MIN. BuRST PRES. PSI 70° PRES. PSI 70°
Part Number Key:
NT10006RD-100

Catalog Color Coil Number Length
Connectors (cont.):
Push>Connect pgs. 57-67
Push>Connect Flow Controls pgs. 58, 68-69
Push>Connect Plus pgs. 69-71
Molded Compression pgs. 126-134

MIN. BEND lBS. PER COIl
RADIuS 70° F 100 FT. lENGTh(S) (FT)

TP16002 1/8 (.125) .023 250 1,000 .62” .30 100, 1,000
TP16025 5/32 (.156) .029 250 1,000 1” .75 100, 1,000
TP16004 1/4 (.250) .040 250 1,000 1.25” 1.2 100, 1,000
TP16005 5/16 (.312) .040 250 1,000 2” 2.0 100, 1,000
TP16006 3/8 (.375) .062 250 1,000 3” 2.7 100, 1,000
TP16008 1/2 (.500) .062 250 1,000 4.5” 3.8 100, 500

MTP160 Polyamide “Nylon 11” Metric

Tubing Typical Application: Flexible nylon tubing. Used for instrumentation; lubrication and air lines; gas, chemical and oil processing; low pressure hydraulics.
CATAlOG TuBE TuBE NuMBER O.D. (MM) WAll (MM)

Temperature Range:
-40°F to +200°F
(-40°C to +93°C)

Available Colors:
Natural (NA).
MAx. WORk. MIN. BuRST PRES. PSI 75° PRES. PSI 75°
Contains:
Ultra-Violet Stabilizer
Connector:
Metric Push>Connect pgs. 57-67

MIN. BEND lBS. PER COIl
RADIuS 75° F 100 FT. lENGTh(S) (FT)

MTP16004 4 .65 250 1,000 .75" 0.6 100
MTP16005 5 1 250 1,000 1" 0.9 100
MTP16006 6 1 250 1,000 1.5" 1.1 100
MTP16008 8 1 250 1,000 2.25" 1.5 100
MTP16010 10 1 200 800 3" 1.9 100
MTP16012 12 1 112 450 3.5" 2.3 100

Brass Products
Introduction

Eaton brass tube fittings are made from high quality UNS CA-360 brass bar. Eaton brass connectors are precision machined to meet SAE standards and specifications. Large, uniform wrench pad areas have standard dimensions for easy assembly and disassembly using standard open-end wrenches. On fittings where pipe threads are used, the fittings are standardized on Dryseal American National Standard Taper. Eaton offers the only complete line of brass connectors with these outstanding advantages.
Shapes
The dies through which the billets are forced may be one of hundreds of shapes. Four of the most common shapes, used in the manufacture of Eaton connectors, are illustrated.

Hot Extrusion
A cast billet is heated and extruded through a die containing the desired configuration. This process recrystallizes the weaker cast structure into the stronger pressed structure of the shaped extrusion.
Hot Extrusion

Cold Draw
The hot extruded shape is pulled through a die with the same configuration but less cross sectional area. This further recrystallizes and refines the structure while increasing the strength and elongation. In addition, the dimensions are brought to close tolerances.

Saw and Machine
The cold bar stock is then cut into individual pieces for precision machining. After the part is machined, it is ready for the market as a strong, tough, high quality connector. Only by using this process is it possible to get the big all-flat sides on elbows and tees, instead of the usual small wrench pads, or lack of flats all together.

Microstructure
The photomicrographs illustrate the change in microstructure from the low strength low ductility dendritic structure of the cast billet, to the recrystallized structure of the hot extrusion, to the refined structure of the high strength high ductility cold drawn rod.

As Cast – 50x Hot Extruded
– 200x

Cold Drawn
– 200x

Refer to safety information regarding Brass Products Note: For additional tech-
proper selection of tubing and tube

nical questions, contact
Inverted Flare Technical Support at connectors on page 1. 1-888-258-0222.
A

Tube O.D. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1
Thread

5/16-28 3/8-24 7/16-24 1/2-20 5/8-18 11/16-18 3/4-18 7/8-18 1-1/16-16 1-3/16-16 1-5/16-16
Size-B

Typical Application:
Hydraulic brake, power steering, fuel lines and transmission cooler lines, LP and natural gas (special order).
Pressure:

Working pressure up to 2000 psi depending on tube size. Will withstand burst pressure of standard tubing - up to 5000 psi with bundy-weld (double flared) and 3500 psi with copper tubing, depending on size.
Vibration:

Excellent resistance.
Temperature Range:
-65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
Material:
CA360 Brass.
Used With:

Copper, brass, aluminum and steel hydraulic tubing that can be flared. See pages 22-26 for material compatibility.
Advantages:

Very low cost and reusable. Seats and threads are internal and protected. Compact, excellent vibration life. Short nut affords very close tube bends. Steel or brass tube nut.
Conformance:

Listed by Underwriter’s Laboratories (available on special order) for fuel equipment, refrigeration and gas. Meets specifications and standards of ASA, ASME, SAE and MS (Military Standards).
How to Order:

Order individually by catalog number.
Note:

Refer to current price list for availability of cataloged items. Configurations and dimensions subject to change without notice. Additional information can be found in SAE J512.
Label Set:
W-8022 (adhesive) CL-490 (non-adhesive)
Assembly Instructions:
1.
Cut tubing to desired length. Make sure all burrs are removed and the ends are cut square.

2.
Slide nut on tube. Threaded end “A” of nut must face out.

3.
Flare end of tube with a 45° flaring tool. See page 20 for flare data.

a.
Measure flare diameter.

b.
Examine flare for excessive thin out.

c.
On thin wall, welded or brazed tubing, use double flare to prevent pinch-off and cracked flares.

4.
Lubricate threads and assemble to connector body. Nut should be turned hand tight.

5.
Tighten assembly with a wrench until a solid feeling is encountered. From that point, apply a one-sixth turn.

Note:
Do not over-torque as it may damage the connectors or split the tubing at the flare.

O.D. NuMBEr C Dl

Brass Products TuBE CATAlOg
Inverted Flare 1/8 105x2 5/16 0.132 0.52 3/16 105x3 3/8 0.196 0.56 1/4 105x4 7/16 0.259 0.56 5/16 105x5 1/2 0.321 0.62
Tube Nut
L
3/8 105x6 5/8 0.384 0.66
C
(Steel) 3/8 105x6x7* 11/16 0.387 0.66
7/16 105x7 11/16 0.444 0.68
(Ref. SAE No. 040110)
D
90°
1/2 105x8 3/4 0.508 0.74 5/8 105x10 7/8 0.632 0.80 3/4 105x12 1-1/16 0.757 0.88 7/8 105x14 1-3/16 0.882 1.06 1 105x16 1-3/8 1.008 1.18
*3/8" Tube to 11/16-18 Male Thread
TuBE CATAlOg
Tube Nut
L
O.D. NuMBEr C Dl
C
(Brass)
3/16 100x3 3/8 .196 0.56
(Ref. SAE No. 040110) 1/4 100x4 7/16 .259 0.56
D
90°
5/16 100x5 1/2 .321 0.62 3/8 100x6 5/8 .384 0.66 1/2 100x8 3/4 .508 0.74
TuBE CATAlOg
Plug
L
O.D. NuMBEr C Dl
C
(Steel)
3/16 131x3 3/8 .188 0.53
(Ref. SAE No. 040109) 1/4 131x4 7/16 .188 0.54
D
5/16 131x5 1/2 .250 0.59
42°
3/8 131x6 5/8 .312 0.66
TuBE CATAlOg
Tube Nut long
L
O.D. NuMBEr C Dl
C
(Steel)
3/16 7896x3 3/8 .196 .844 1/4 7896x4 7/16 .257 .812
D
90°
Required for wheel cylinders with deep port connection.
TuBE CATAlOg
union
L
O.D. NuMBEr C Dl
C
(Ref. SAE No. 040101)
1/8 302x2 13/32 .078 .59 3/16 302x3 15/32 .125 .62 D 1/4 302x4 17/32 .188 .62 5/16 302x5 19/32 .219 .70 3/8 302x6 3/4 .281 .80 1/2 302x8 29/32 .406 .91 5/8 302x10 1-1/16 .531 .97
MTO - Made To Order

Brass Products

Inverted Flare

Adapter SAE 45° SAE
TuBE iNvErTED CATAlOg l

Flare to inv. Flare SizE MAlE NuMBEr C D
1/4 3/16 1518 7/16 .189 1.031 1/4 1/4 1522 7/16 .188 1.031 3/8 5/16 1553 5/8 .234 1.340 3/8 3/8 1563 5/8 .282 1.380 3/8 7/16 1554 11/16 .282 1.400
TuBE MAlE PiPE CATAlOg
Male Connector
O.D. ThrEAD NuMBEr C Dl

L
C
(Ref. SAE No. 040102)

1/8 1/8 202x2 13/32 .078 0.62 3/16 1/8 202x3 15/32 .125 0.70 D 1/4 1/8 202x4 17/32 .188 0.74 1/4 1/4 202x4x4 9/16 .188 0.89 5/16 1/8 202x5 19/32 .219 0.79 Pipe end drill may be reduced or increased 5/16 1/4 202x5x4 19/32 .220 0.98 from seat dimension 'D'. 3/8 1/8 202x6x2 3/4 .281 0.89 3/8 1/4 202x6 3/4 .281 1.03 3/8 3/8 202x6x6 3/4 .281 1.01 1/2 1/4 202x8x4 29/32 .406 1.08 1/2 3/8 202x8 29/32 .406 1.07 1/2 1/2 202x8x8 29/32 .406 1.26 5/8 1/2 202x10 1-1/16 .531 1.32 3/4 3/4 202x12 1-1/4 .625 1.39 7/8 3/4 202x14 1-3/8 .750 1.38 1 1 202x16 1-1//2 .812 1.62
MTO - Made To Order
TuBE FEM. PiPE CATAlOg
Female Connector

L
O.D. ThrEAD NuMBEr C Dl

C
(Ref. SAE No. 040103)

3/16 1/8 252x3 1/2 .125 0.75 1/4 1/8 252x4 17/32 .188 0.75 D 5/16 1/8 252x5 19/32 .219 0.78 3/8 1/4 252x6 3/4 .281 1.03 1/2 3/8 252x8 29/32 .406 1.09
MTO - Made To Order
TuBE MAlE PiPE CATAlOg
45° Male Elbow

L
O.D. ThrEAD NuMBEr C DD1lM N

D
C
(Ref. SAE No. 040302)
3/16 1/8 352x3 17/32 .125 .156 0.88 0.25 0.55 1/4 1/8 352x4 9/16 .188 .188 0.94 0.27 0.58 5/16 1/8 352x5 5/8 .219 .203 1.00 0.34 0.56

D1
5/16 1/4 352x5x4 5/8 .219 .203 1.16 0.23 0.83

M 3/8 1/4 352x6 25/32 .281 .219 1.34 0.41 0.84 1/2 3/8 352x8 7/8 .406 .375 1.44 0.38 0.91
N
MTO - Made To Order

Brass Products
Inverted Flare
90° union Elbow
(Ref. SAE No. 040201)

90° Male Elbow
(Ref. SAE No. 040202)

90° Female Elbow
(Ref. SAE No. 040203)

TuBE O.D. CATAlOg NuMBEr D l X
1/4 502x4 .188 0.77 0.53
5/16 502x5 .219 0.86 0.59
3/8 502x6 .281 1.04 0.72

MTO - Made To Order
TuBE MAlE PiPE CATAlOg
O.D. ThrEAD NuMBEr D D1 l l1 M X
1/8 1/8 402x2 .078 .116 0.80 0.47 0.27 0.42
3/16 1/8 402x3 .125 .125 0.85 0.47 0.27 0.47
1/4 1/8 402x4 .188 .177 0.92 0.55 0.33 0.53
D1 1/4 1/8 431x4* .188 .062 0.91 0.53 0.33 0.53

1/4 1/4 402x4x4 .188 .188 1.09 0.58 0.28 0.56
5/16 1/8 402x5 .219 .219 0.98 0.67 0.47 0.59
5/16 1/4 402x5x4 .219 .219 1.16 0.75 0.45 0.59
5/16 3/8 402x5x6 .219 .219 1.15 0.69 0.34 0.59
3/8 1/8 402x6x2 .281 .219 1.14 0.75 0.54 0.76
3/8 1/4 402x6 .281 .281 1.32 0.82 0.53 0.76
3/8 3/8 402x6x6 .281 .312 1.32 0.84 0.50 0.75
1/2 1/4 402x8x4 .406 .281 1.47 0.94 0.59 0.91
1/2 3/8 402x8 .406 .375 1.48 0.94 0.59 0.92
1/2 1/2 402x8x8 .406 .406 1.67 1.09 0.66 0.91
5/8 3/8 402x10x6 .531 .437 1.62 1.11 0.67 1.06
5/8 1/2 402x10 .531 .500 1.82 1.11 0.67 1.06
3/4 1/2 402x12x8 .625 .531 2.01 1.30 0.80 1.25
7/8 3/4 402x14 .750 .750 2.12 1.46 0.94 1.38
1 1 402x16 .812 .812 2.44 1.70 1.02 1.50

*.062 dia. restricted hole through pipe end. Available on special order with any restricted hole size up to .172 dia. MTO - Made To Order
TuBE FEM. PiPE CATAlOg
O.D. ThrEAD NuMBEr D l X
3/16 1/8 452x3 .125 0.81 0.50
1/4 1/8 452x4 .188 0.81 0.53
5/16 1/8 452x5 .219 0.88 0.59
3/8 1/4 452x6 .281 1.05 0.75

MTO - Made To Order

Brass Products
Inverted Flare
TuBE CATAlOg
union Tee
L
O.D. NuMBEr D l l1 M
(Ref. SAE No. 040401)
1/8 702x2 .078 0.94 0.53 .330
D
3/16 702x3 .125 1.09 0.62 .390
M
1/4 702x4 .188 1.13 0.69 .420
D
L1 5/16 702x5 .219 1.25 0.75 .450 3/8 702x6 .281 1.48 0.94 .560
TuBE MAlE PiPE CATAlOg
Male run Tee
L
O.D. ThrEAD NuMBEr D l l1 M M1
M1
(Ref. SAE No. 040424)
3/16 1/8 752x3 .125 1.25 0.62 0.39 0.53
D
1/4 1/8 752x4 .188 1.31 0.69 0.42 0.56
5/16 1/8 752x5 .219 1.47 0.75 0.45 0.62
M
L1
3/8 1/4 752x6 .281 1.83 0.94 0.56 0.75 1/2 3/8 752x8 .406 .406 1.39 1.47 0.91
MTO - Made To Order
TuBE MAlE PiPE CATAlOg
Male Branch Tee
D1
O.D. ThrEAD NuMBEr D D1 l l1 X
(Ref. SAE No. 040425)
3/16 1/8 602x3 .125 .219 0.82 0.84 0.47 1/4 1/8 602x4 .188 .219 0.84 0.91 0.53
L1
5/16 1/8 602x5 .219 .219 0.95 0.97 0.59
DX
3/8 1/4 602x6 .281 .344 1.16 1.31 0.75 1/2 3/8 602x8 .406 .406 1.39 1.47 0.91
MTO - Made To Order
L
TuBE FEM. PiPE CATAlOg
Female Branch Tee
O.D. ThrEAD NuMBEr D l l1 N
L
(Ref. SAE No. 040427)
3/16 1/8 652x3 .125 1.10 0.62 0.39 1/4 1/8 652x4 .188 1.12 0.69 0.42
N
L1 MTO - Made To Order
D

Refer to safety information regarding

Brass Products Note:
proper selection of tubing and tube SAE 45° Flare questions, contact connectors on page 1. Technical Support at 1-888-258-0222.
For additional technical

Tube O.D. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4
Thread

5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 11/16-18 3/4-16 7/8-14 1-1/16-14
Size-B
Typical Application:
LP and natural gas, flammable liquids (special order), instrumentation, refrigeration, power steering, hydraulic and pneumatic systems.
Pressure:
Working pressure up to 2000 psi depending on tube size. Will withstand burst pressure of standard tubing - up to 5000 psi with bundy-weld (double flared) and 3500 psi with copper tubing, depending on size.
Vibration:
Good resistance - use long nut when greater vibration resistance is required.
Temperature Range:
-65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
Material:
CA360 Brass.
Used With:
Copper, brass, aluminum and steel hydraulic tubing that can be flared. See pages 22-26 for material compatibility.
Advantages:
Low cost and reusability, long or short nut. Good resistance to vibration.
Conformance:
Listed by Underwriter’s Laboratories (available on special order) for flammable liquids, refrigeration and gas. Meets specifications and standards of ASA, ASME, SAE and MS (Military Standards).
How to Order:
Order individually by catalog number.
Note:
Refer to current price list for availability of cataloged items. Configurations and dimensions subject to change without notice. Quotations of non-stock items available upon request. Additional information can be found in SAE J512.
Assembly Instructions:
1.
Cut tubing to desired length. Make sure all burrs are removed and the ends are cut square.

2.
Slide nut on tube. Threaded end “A” of nut must face out.

3.
Flare end of tube with a 45° flaring tool. See page 20 for flare data.

a.
Measure flare
diameter.

b.
Examine flare for excessive thin out.

4.
Lubricate threads and assemble to connector body. Nut should be turned hand tight.

5.
Tighten assembly with a wrench until a solid feeling is encountered. From that point, apply a one-sixth turn.

Note:
Do not over-torque as it may damage the connector or split the tubing at the flare.
Label Set:
W-8022 (adhesive) CL-490 (non-adhesive)

Brass Products
SAE 45° Flare
Nut
(Ref. SAE No. 010110)
L
C
D
long Nut
L
C
(Ref. SAE No. 010111)
D
Cap
L
C
Plug
L
(Ref. SAE No. 010109)
D1
C
union
L
C
(Ref. SAE No. 010101)
D
TuBE CATAlOg
O.D. NuMBEr C Dl
1/8 1110x2 3/8 .133 0.50
3/16 1110x3 7/16 .195 0.62
1/4 1110x4 9/16 .258 0.75
5/16 1110x5 5/8 .320 0.88
3/8 1110x6 3/4 .383 1.00
7/16 1110x7 13/16 .445 1.06
1/2 1110x8 7/8 .508 1.12
5/8 1110x10 1-1/16 .633 1.31
3/4 1110x12 1-1/4 .758 1.50
MTO - Made To Order
TuBE CATAlOg
O.D. NuMBEr C Dl
3/16 41x3 7/16 .195 0.81
1/4 41x4 9/16 .258 0.94
5/16 41x5 5/8 .320 1.12
3/8 41x6 3/4 .383 1.31
1/2 41x8 7/8 .508 1.62
5/8 41x10 1-1/16 .633 1.88
MTO - Made To Order
TuBE CATAlOg
O.D. NuMBEr C l
1/8 40x2 7/16 0.40
3/16 40x3 1/2 0.47
1/4 40x4 7/16 0.53
5/16 40x5 5/8 0.62
3/8 40x6 3/4 0.69
1/2 40x8 7/8 0.84
5/8 40x10 1-1/16 0.97
3/4 40x12 1-5/16 1.09
TuBE CATAlOg D1
O.D. NuMBEr C l (OPT.)
1/8 39x2 5/16 0.47 .079
3/16 39x3 3/8 0.58 .126
1/4 39x4 7/16 0.69 .189
5/16 39x5 1/2 0.79 .220
3/8 39x6 5/8 0.88 .282
1/2 39x8 3/4 1.06 .408
5/8 39x10 7/8 1.19 .502
3/4 39x12 1-1/16 1.31 .627
TuBE CATAlOg
O.D. NuMBEr C Dl
1/8 42x2 5/16 .078 0.92
3/16 42x3 3/8 .125 1.06
1/4 42x4 7/16 .188 1.19
5/16 42x5 1/2 .219 1.34
3/8 42x6 5/8 .281 1.50
1/2 42x8 3/4 .406 1.81
5/8 42x10 7/8 .500 2.12
3/4 42x12 1-1/16 .625 2.44
MTO - Made To Order

Brass Products
SAE 45° Flare
Male Connector
(Ref. SAE No. 010102)
*Counterbore is optional.
Female Connector
(Ref. SAE No. 010103)
D
L
D
TuBE
L
O.D.
C
1/8
D1 3/16 1/4 1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 3/4 3/4
TuBE
O.D.
C
3/16 1/4 1/4 5/16 5/16 3/8 3/8 3/8 1/2 1/2 5/8 5/8 5/8
FEM. PiPE ThrEAD
1/8
1/8
1/8
1/4
1/8
1/4
1/8
1/4
3/8
1/2
1/4
3/8
1/2
3/8
1/2
1/2
3/4
FEM. PiPE ThrEAD
1/8
1/8
1/4
1/8
1/4
1/4
3/8
1/2
3/8
1/2
3/8
1/2
3/4
CATAlOg NuMBEr C Dl l1
48x2 7/16 .078 .219 0.90
48x3 7/16 .125 .219 1.00
48x4 7/16 .188 .188 1.06
48x4x4 9/16 .188 .312 1.26
48x5 1/2 .219 .219 1.16
48x5x4 9/16 .219 .219 1.34
48x6x2 5/8 .281 .219 1.25
48x6 5/8 .281 .281 1.44
48x6x6 11/16 .281 .281 1.44
48x6x8 7/8 .281 .562* 1.69
48x8x4 3/4 .406 .312 1.62
48x8 3/4 .406 .406 1.62
48x8x8 7/8 .406 .562 1.81
48x10x6 7/8 .500 .406 1.81
48x10 7/8 .500 .500 2.00
48x12 1-1/16 .625 .562 2.18
48x12x12 1-1/16 .625 .625 2.18
CATAlOg NuMBEr C Dl
46x3 9/16 .125 0.97
46x4 9/16 .188 1.03
46x4x4 11/16 .188 1.25
46x5 9/16 .219 1.06
46x5x4 11/16 .219 1.28
46x6 11/16 .281 1.31
46x6x6 13/16 .281 1.38
46x6x8 1 .281 1.62
46x8 13/16 .406 1.50
46x8x8 1 .406 1.75
46x10x6 7/8 .500 1.59
46x10w 1 .500 1.81
46x10x12 1-1/4 .500 1.90
CATAlOg NuMBEr C Dl
43x4 7/16 .125 1.06
43x6 5/8 .219 1.31
CATAlOg NuMBEr D MN
54x4 .188 0.67 0.64
54x4x4 .188 0.73 0.87
54x5 .219 0.78 0.64
54x6 .281 0.89 0.86
54x8 .406 1.06 0.95
54x8x8 .406 1.12 1.17
54x10x6 .500 1.23 0.98
54x10 .500 1.23 1.17
MTO - Made To Order
Male Ball Check Connector
D
Ball & Spring position may be reversed to change flow/check direction. Min pressure 3 psi.
45° Male Elbow
D
(Ref. SAE No. 010302)
M
TuBE
O.D.
L
C
1/4 3/8
TuBE
O.D.
1/4 1/4 5/16 3/8
N
1/2 1/2 5/8 5/8
MAlE PiPE ThrEAD
1/8
1/4
MAlE PiPE ThrEAD
1/8
1/4
1/8
1/4
3/8
1/2
3/8
1/2

Brass Products
SAE 45° Flare
L
AC Type Adapter
D
C
Adapter SAE 45° Flare to inv. Flare
90° union Elbow
(Ref. SAE No. 010201)
M D
M
90° Male Elbow
(Ref. SAE No. 010202)
D
M D1
N
90° Female Elbow
(Ref. SAE No. 010203)
D
M
N
TuBE SAE TuBE CATAlOg SizE SizE NuMBEr C D l
1/4 1/4 1521 7/16 .188 1.094
SAETuBE iNvErTED CATAlOg SizE MAlE NuMBEr C D l
1/4 3/16 1518 7/16 .189 1.031
1/4 1/4 1522 7/16 .188 1.031
3/8 5/16 1553 5/8 .234 1.340
3/8 3/8 1563 5/8 .282 1.380
3/8 7/16 1554 11/16 .282 1.400
TuBE CATAlOg
O.D. NuMBEr D M
1/2 55x8 .406 1.20
3/4 55x12 .625 1.64
MTO - Made To Order
TuBE MAlE PiPE CATAlOg
O.D. ThrEAD NuMBEr D D1 M N
1/8 1/8 49x2 .078 .219 0.62 0.69
3/16 1/8 49x3 .125 .219 0.75 0.75
1/4 1/8 49x4 .188 .219 0.81 0.76
1/4 1/4 49x4x4 .188 .312 0.88 0.94
1/4 3/8 49x4x6 .188 .375 0.94 1.03
5/16 1/8 49x5 .219 .219 0.91 0.78
5/16 1/4 49x5x4 .219 .312 0.95 0.92
3/8 1/8 49x6x2 .281 .219 1.03 0.91
3/8 1/4 49x6 .281 .312 0.97 1.06
3/8 3/8 49x6x6 .281 .406 1.06 1.09
3/8 1/2 49x6x8 .281 .438 1.16 1.28
1/2 1/4 49x8x4 .406 .281 1.22 1.19
1/2 3/8 49x8 .406 .406 1.22 1.12
1/2 1/2 49x8x8 .406 .406 1.26 1.35
5/8 3/8 49x10x6 .500 .410 1.41 1.23
5/8 1/2 49x10 .500 .562 1.41 1.38
3/4 1/2 49x12 .625 .531 1.62 1.50
3/4 3/4 49x12x12 .625 .750 1.59 1.62
TuBE FEM. PiPE CATAlOg
O.D. ThrEAD NuMBEr D M N
1/4 1/8 50x4 .188 0.88 0.47
1/4 1/4 50x4x4 .188 0.97 0.66
3/8 1/4 50x6 .281 1.09 0.69
MTO - Made To Order

Brass Products
SAE 45° Flare
union Tee
(Ref. SAE No. 010401)
Male run Tee
(Ref. SAE No. 010424)
Male Branch Tee
(Ref. SAE No. 010425)
Adapter Tee
(Female to Male Pipe on Run)
TuBE CATAlOg
O.D. NuMBEr D M
3/16 44x3 .125 0.73
M
1/4 44x4 .188 0.86 D 3/8 44x6 .281 1.04 1/2 44x8 .406 1.20
M M
MTO - Made To Order
TuBE MAlE PiPE CATAlOg D1
O.D. ThrEAD NuMBEr D OPT. M N
D
1/4 1/8 51x4 .188 .219 0.86 0.76
MTO - Made To Order
M D1
M N
D1 MAlE
TuBE PiPE CATAlOg

O.D. ThrEAD NuMBEr D D1 M NP
N 1/4 1/8 45x4 .188 .219 0.81 0.78
D
3/8 3/8 45x6x6x6 .281 .406 1.06 1.09
1/2 3/8 45x8 .406 .406 1.22 1.12
M M
1/2 1/2 45x8x8x8 .406 .562 1.28 1.38
MTO - Made To Order
MAlE
D
TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D D1 M N N1
M 1/4 1/8 56x4w .188 .188 0.78 0.76 0.46
MTO - Made To Order
D1 N N1

Refer to safety information regarding

Brass Products Note:
proper selection of tubing and tube Compression questions, contact connectors on page 1.
Technical Support at 1-888-258-0222.
For additional technical
A

Tube O.D. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1
Thread

5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18 1-1/4-18
Size-B
Typical Application:
Instrumentation, hydraulic and pneumatic systems.
Pressure:
Working pressure up to 2000 psi with a 4:1 safety factor depending on tube size. When using plastic tubing, use the working pressure for type used.
Vibration:
Fair resistance - use long nut when greater vibration resistance is needed.
Temperature Range:
65°F to +250°F (-53°C to +121°C) with metal tubing. When using compatible plastic tubing do not exceed the tubing temperature range. (Refer to tubing temperature range.)
Material:
CA360 Brass.
Used With:
Aluminum, copper and plastic tubing.
Plastic tubing, except for PT230 and TP160, requires 2030x insert. Not recommended for steel tubing. See pages 22-26 for material compatibility, and pages 27-29 for plastic tubing.
Advantages:
Low cost. Easy to assemble, no flaring. Available with long or short nut. Broad selection of styles and sizes.
Conformance:
Listed by Underwriter’s Laboratories (available on special order) for flammable liquids. Meets specifications and standards of ASA, ASME and SAE.
How to Order:
Compression connectors are ordered as complete assemblies (body, nut and sleeve). To order assembly supplied with long nuts, simply add the prefix “1” to the catalog number. Example: 68x4 with long nut becomes 168x4. Nuts and sleeves can be ordered separately by catalog number. To order bodies only (less nut and sleeve). prefix catalog number with letter “B”. Example: B68x4.
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice. Additional information can be found in SAE J512.
Assembly Instructions:
1.
Cut tubing to desired length.

2.
Slide nut and then sleeve on tube. Threaded end “A” of nut must face toward connector.

3.
Insert tubing into connector body. Be sure tubing is bottomed on connector shoulder.

4.
Lubricate threads and assemble nut to connector body.

5.
Tighten nut hand tight. From that point, tighten with a wrench the number of turns indicated in the chart below.

TuBE ADDiTiONAl TurNS SizE FrOM hANDTighT
1/8" thru 1/4" 1-1/4
5/16" 1-3/4
3/8" thru 1" 2-1/4

Label Set:
W-8022 (adhesive) CL-490 (non-adhesive)

Brass Products
Compression

H and H1 are hand tight dimensions.
Tube Support for Plastic Tubing

Use only with PT200 and PT240 Tubing.
Compression Sleeve
(Ref. SAE No. 060115)

Nut
(Ref. SAE No. 060110)

TuBE E TuBE STOP
O.D. DEPTh h h1 (lONg NuT)
1/8 0.19 0.23 –
3/16 0.22 0.25 0.47
1/4 0.25 0.29 0.56
5/16 0.28 0.30 0.66
3/8 0.31 0.27 0.70
1/2 0.38 0.42 0.88
5/8 0.38 0.42 0.92
3/4 0.44 0.49 1.18
TuBE CATAlOg DiA. O.D. NuMBEr A DiA. B DiA. lENgTh C D
1/4 2030x4* 1/8 3/32 11/64 19/32
1/4 2030x44** 11/64 9/64 7/32 17/32
5/16 2030x5 3/16 5/32 15/64 5/8
3/8 2030x6 1/4 7/32 11/32 41/64
1/2 2030x8 3/8 11/32 7/16 13/16
5/8 2030x10 1/2 29/64 35/64 13/16
3/4 2030x12 9/16 33/64 11/16 1-1/32
* For Tubing with .126 I.D./.062 wall thickness.
** For tubing with .170 I.D./.040 wall thickness.
TuBE CATAlOg O.D. NuMBEr D F l
1/8 60x2 0.13 0.19 0.19
3/16 60x3 0.19 0.27 0.22
1/4 60x4 0.26 0.34 0.25
5/16 60x5 0.32 0.41 0.25
3/8 60x6 0.38 0.47 0.25
7/16 60x7 0.44 0.53 0.31
1/2 60x8 0.51 0.59 0.38
5/8 60x10 0.63 0.72 0.38
3/4 60x12 0.76 0.88 0.44
MTO - Made To Order
TuBE CATAlOg O.D. NuMBEr D l
1/8 61x2 3/8 0.13 0.38
3/16 61x3 7/16 0.19 0.41
1/4 61x4 1/2 0.26 0.44
5/16 61x5 9/16 0.32 0.44
3/8 61x6 5/8 0.38 0.47
7/16 61x7 11/16 0.44 0.50
1/2 61x8 13/16 0.51 0.62
5/8 61x10 15/16 0.63 0.62
5/8 61x12 1-3/16 0.76 0.69

MTO - Made To Order

Brass Products

Compression

TuBE CATAlOg
long Nut

O.D. NuMBEr

D l
(Ref. SAE No. 060111)

3/16 1611x3 7/16 .193 0.62 1/4 1611x4 9/16 .260 0.75 5/16 1611x5

5/8 .320 0.84
3/8 1611x6 11/16 .380 0.88
1/2 1611x8

13/16 .510 1.06 5/8 1611x10

15/16 .637 1.08 3/4 1611x12

1-1/8 .760 1.38

MTO - Made To Order
TuBE CATAlOg

ThrEAD
Bulkhead Nut

O.D. NuMBEr l SizE
1/4 0102x4 9/16 0.25 7/16–24 3/8 0102x6 11/16 0.25 9/16–24 1/2 0102x8 15/16 0.38 11/16–20
Used on 74x Bulkhead Unions. Ref. page 44.

TuBE CATAlOg
union

O.D. NuMBEr

D l
(Ref. SAE No. 060101BA)

1/8 62x2 5/16 .094 0.66 3/16 62x3 3/8 .125 0.76 1/4 62x4 7/16 .188 0.79 5/16 62x5 1/2 .250 0.88 3/8 62x6 9/16 .312 0.97 1/2 62x8 11/16 .406 1.10
Assembly with long nut 162x.
Not available in the x3 style. 5/8 62x10 13/16 .500 1.25

3/4 62x12

1 .562 1.44

MTO - Made To Order
TuBE MAlE PiPE CATAlOg

D1
Male Connector

O.D. ThrEAD NuMBEr D OPT. l
(Ref. SAE No. 060102BA)

1/8 1/16 68x2x1 3/8 .094 – 0.78 1/8 1/8 68x2 7/16 .094 .094 0.78 3/16 1/8 68x3 7/16 .125 .125 0.84 1/4 1/8 68x4 7/16 .188 .188 0.88 1/4 1/4 68x4x4 9/16 .188 .312 1.06
Assembly with long nut 168x. 5/16 1/8 68x5 1/2 .250 .234 0.91 5/16 1/4 68x5x4 9/16 .250 .250 1.09 3/8 1/8 68x6x2 9/16 .312 .250 0.97 3/8 1/4 68x6 9/16 .312 .312 1.17 3/8 3/8 68x6x6 11/16 .312 .312 1.16 3/8 1/2 68x6x8 7/8 .312 .562 1.34 1/2 1/4 68x8x4 11/16 .406 .281 1.22 1/2 3/8 68x8 11/16 .406 .406 1.22 1/2 1/2 68x8x8 7/8 .406 .406 1.41 5/8 1/2 68x10 7/8 .500 .500 1.50 3/4 1/2 68x12

1 .562 .562 1.62 3/4 3/4 68x12x12

1-1/16 .562 .875 1.62

MTO - Made To Order

Brass Products

Compression
Female Connector
(Ref. SAE No. 060103BA)
Assembly with long nut 166x.
Male Ball Check Connector
Assembly with long nut 163x. Min. working pressure 3 psi. Ball and spring position may be reversed to change flow/check direction. Ball check valves are neither tested nor adjusted prior to sale.
Bulkhead union
Assembly with long nut 174x. For Bulkhead Nuts, ref. page 43, included with assembly.

L
C
L
D
C
L
P
C
TuBE
O.D.
1/8 3/16 1/4

D
1/4 5/16 5/16 3/8 3/8 1/2
FEM. PiPE ThrEAD
1/8
1/8
1/8
1/4
1/8
1/4
1/8
1/4
3/8
MTO - Made To Order
TuBE MAlE PiPE
O.D. ThrEAD
1/4 1/8
3/8 1/4
TuBE
O.D.
1/4 3/8
MTO - Made To Order

D
CATAlOg NuMBEr C D l
66x2 9/16 .094 0.75
66x3 9/16 .125 0.78
66x4 9/16 .188 0.78
66x4x4 11/16 .188 1.03
66x5 9/16 .250 0.81
66x5x4 11/16 .250 1.03
66x6x2 9/16 .312 0.84
66x6 11/16 .312 1.06
66x8 13/16 .406 1.12
CATAlOg NuMBEr C Dl
63x4 7/16 .125 0.88
63x6 9/16 .219 1.16
CATAlOg MAX. NuMBEr C Dl P
74x4 9/16 .188 1.57 0.52
74x6 11/16 .312 1.76 0.55

Brass Products

Compression

TuBE MAlE PiPE CATAlOg
90° Male Elbow
O.D. ThrEAD NuMBEr D D1 M N
(Ref. SAE No. 060202BA)
1/8 1/16 69x2x1 .104 .125 0.54 0.66 1/8 1/8 69x2 .094 .219 0.60 0.67 3/16 1/8 69x3 .125 .219 0.62 0.69

D1 1/4 1/8 69x4 .188 .219 0.62 0.75 D

1/4 1/4 69x4x4 .188 .188 0.62 0.75 5/16 1/8 69x5 .250 .234 0.62 0.75 5/16 1/4 69x5x4 .250 .312 0.69 0.84 3/8 1/8 69x6x2 .312 .234 0.69 0.69
Assembly with long nut 169x.

3/8 1/4 69x6 .312 .344 0.75 0.94 3/8 3/8 69x6x6 .312 .438 0.84 0.94 3/8 1/2 69x6x8 .312 .531 1.06 1.12 7/16 1/4 69x7
.312 .312 0.84 1.00 1/2 1/4 69x8x4 .406 .312 0.84 0.94 1/2 3/8 69x8 .406 .406 0.94 1.12 1/2 1/2 69x8x8 .406 .531 0.94 1.31 5/8 1/2 69x10 .500 .562 1.06 1.31 3/4 1/2 69x12

.562 .562 1.19 1.50 3/4 3/4 69x12x12

.562 .562 1.19 1.31

MTO - Made To Order

TuBE CATAlOg
90° union Elbow
O.D. NuMBEr D M
(Ref. SAE No. 060201BA)
1/4 65x4 .188 0.60 5/16 65x5 .250 0.62 3/8 65x6 .312 0.73 1/2 65x8 .406 0.94

TuBE FEM. PiPE CATAlOg
90° Female Elbow
O.D. ThrEAD NuMBEr D M N
(Ref. SAE No. 060203BA)
3/16 1/8 70x3 .125 0.69 0.56 1/4 1/8 70x4 .188 0.69 0.56 3/8 1/4 70x6

.312 0.81 0.75 1/2 3/8 70x8

.406 1.00 0.88

MTO - Made To Order

Assembly with long nut 170x.

Brass Products

Compression
TuBE CATAlOg
union Tee
O.D. NuMBEr D M

D
(Ref. SAE No. 060401BA)

M 3/16 64x3 .125 0.60 1/4 64x4 .188 0.62 5/16 64x5 .250 0.60
M M

3/8 64x6 .312 0.73 1/2 64x8 .406 0.94
Assembly with long nut 164x.
TuBE MAlE PiPE CATAlOg
Male run Tee

D O.D. ThrEAD NuMBEr D D1 M N (Ref. SAE No. 060424BA) M
3/16 1/8 71x3 .125 .219* 0.64 0.68 D1 1/4 1/8 71x4 .188 .219* 0.64 0.73 3/8 1/4 71x6 .312 .344* 0.75 0.94
M N

*Optional Counterbore.
Assembly with long nut 171x.
TuBE MAlE PiPE CATAlOg
Male Branch Tee D1
O.D. ThrEAD NuMBEr D D1 M N
(Ref. SAE No. 060425BA)
3/16 1/8 72x3 .125 .219 0.62 0.69

DN
1/4 1/8 72x4 .188 .219 0.64 0.73 1/4 1/4 72x4x4x4 .188 .281 0.78 0.85 5/16 1/8 72x5 .250 .234 0.66 0.70
M M

3/8 1/4 72x6 .312 .344 0.78 0.91 1/2 3/8 72x8 .406 .406 0.96 1.09
Assembly with long nut 172x.
MTO - Made To Order
Adapter Tee
(Female to Male Pipe on Run)
N

N1
D
M
D1
TuBE M&F PiPE CATAlOg
O.D. ThrEAD NuMBEr D D1 M N N1
1/4 1/8 76x4 .188 .219 0.59 0.63 0.47
MTO - Made To Order

Refer to safety information regarding

Brass Products Note:
proper selection of tubing and tube Selfalign questions, contact connectors on page 1.
Technical Support at 1-888-258-0222.
For additional technical
A

Thread Size B

Tube O.D. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 1
Thread

5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18 1-1/4-18
Size-B
Typical Application:
Instrumentation, hydraulic and pneumatic systems.
Pressure:
Working pressure up to 2000 psi with a 4:1 safety factor depending on tube size. When using plastic tubing, use the working pressure for type used.
Vibration:
Good resistance - use long nut when greater vibration resistance is needed.
Temperature Range:
-65°F to +250°F (-53°C to +121°C) with metal tubing. When using compatible plastic tubing do not exceed the tubing temperature range. (Refer to tubing temperature range.)
Material:
CA360 Brass.
Used with:
Aluminum, copper and plastic tubing.
Plastic tubing, except for PT230 and TP160, requires 2030x insert. Not recommended for steel tubing. See pages 22-26 for material compatibility, and pages 2729 for plastic tubing.
Advantages:
Very low cost and reusable. Self aligning - no need to disassemble fitting to line up sleeve on tube. Low cost. Easy to assemble, no flaring. Available with long or short nut. Broad selection of styles and sizes.
Conformance:
An exclusive product design, user approvals only.
How to Order:
Selfalign connectors are ordered as complete assemblies (body, nut and sleeve). To order assembly supplied with long nuts, simply add the prefix “1” to the catalog number. Example: 681x4 with long nut becomes 1681x4. Nuts and sleeves can be ordered separately by catalog number. To order bodies only (less nut and sleeve), prefix catalog number with the letter “B” and drop suffix number. Example: B68x4.
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice.
Assembly Instructions:
1.
Cut tubing to desired length.

2.
Slide nut and then sleeve on tube. Threaded end of nut “A” and small end of sleeve “B” must face toward fitting.

3.
Insert tubing into connector body. Be sure tubing is bottomed on connector shoulder.

4.
Lubricate threads and assemble nut to connector body.

5.
Tighten with wrench to the “ring grip” point.

a. Ring Grip is the point when the cutting edge of the sleeve grips the tube. This is determined by turning tube slowly but firmly by hand while tightening the nut with a wrench until tube can no longer be turned by hand and a sharp increase in torque is noticed.
6. Tighten additional turns past “ring grip” as indicated on chart. Refer to page 48.
Label Set:
CL-500 (non-adhesive)

Brass Products

Selfalign
Selfalign Assembly

Nut Assembly Comparison

Selfalign fitting used with soft plastic tubing and brass insert.

Selfalign Assembly Data Chart
ANNEAlED COPPEr AND SOFT AluMiNuM TuBiNg NylON TuBiNg
Type “T” Type “H”
Fitting Thin Wall Thick Wall
Size Wall Turns* Wall Turns* Wall Turns*

2 .030 1-1/3 – – – –
3 .030 1-1/3 .023 1-2/3 .039 1-1/3
4 .030 1-2/3 .030 2 .050 1-2/3
5 .032 1-2/3 .036 1-2/3 .062 2-2/3
6 .032 2 .040 1-2/3 .075 2
8 .032 2 – – – –
10 .035 2 – – – –
12 .049 2 – – – –
16 .065 2-1/4 – – – –
*Turns from “Ring Grip”
TuBE E TuBE STOP h h1
O.D. DEPTh (STD. NuT) (lONg NuT)
1/8 0.19 0.24 –
3/16 0.22 0.25 0.49
1/4 0.25 0.35 0.61
5/16 0.28 0.30 0.70
3/8 0.31 0.31 0.75
1/2 0.38 0.36 0.83
5/8 0.38 0.41 0.92
3/4 0.44 0.41 1.14

Selfalign fitting used on rigid plastic tubing, no insert.

Brass Products
Selfalign
TuBE O.D. CATAlOg NuMBEr DiA. A DiA. B DiA. C lENgTh D

1/4 2030x4* 1/8 3/32 11/64 19/32
Tube Supports for Plastic Tubing
1/4 2030x44** 11/64 9/64 7/32 17/32 5/16 2030x5 3/16 5/32 15/64 5/8 3/8 2030x6 1/4 7/32 11/32 41/64 1/2 2030x8 3/8 11/32 7/16 13/16 5/8 2030x10 1/2 29/64 35/64 13/16

Use only with PT200 and PT240 Tubing. 3/4 2030x12 9/16 33/64 11/16 1-1/32
*For tubing with .126 I.D./.062 wall. **For tubing with .170 I.D./.040 wall.

TuBE CATAlOg
Sleeve
O.D. NuMBEr D F l

1/8 601x2 0.130 0.25 0.20 3/16 601x3 0.193 0.31 0.20 1/4 601x4 0.256 0.38 0.26 5/16 601x5 0.318 0.44 0.26 3/8 601x6 0.381 0.50 0.26 1/2 601x8 0.507 0.62 0.30 5/8 601x10 0.630 0.72 0.36 3/4 601x12 0.755 0.88 0.38 1 601x16 1.005 1.19 0.50

TuBE CATAlOg
Nut
O.D. NuMBEr

Dl

1/8 611x2 3/8 0.14 0.38 3/16 611x3 7/16 0.19 0.38 1/4 611x4 1/2 0.26 0.44 5/16 611x5 9/16 0.32 0.44 3/8 611x6 5/8 0.38 0.44 1/2 611x8 13/16 0.51 0.52 5/8 611x10 15/16 0.64 0.56

TuBE CATAlOg
long Nut
O.D. NuMBEr

Dl

3/16 1611x3 7/16 .193 0.62 1/4 1611x4 9/16 .260 0.75 3/8 1611x6 11/16 .380 0.88

TuBE CATAlOg
Bulkhead Nut
O.D. NuMBEr

l

1/4 0102x4 9/16 .25 3/8 0102x6 11/16 .25 1/2 0102x8 15/16 .38
Use on 741x Bulkhead Unions. Ref. page 51.

Brass Products
Selfalign
union
Assembly with long nut 1621x.
Male Connector
Assembly with long nut 1681x.
Female Connector
Assembly with long nut 1661x.
Male Ball Check Connector
Assembly with long nut 1631x.
TuBE
L
O.D.
D
1/8 3/16 1/4 5/16
C
I
3/8 1/2 5/8
TuBE
L
O.D.
D
1/8 1/8 3/16 1/4
C
1/4 5/16 5/16 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8
TuBE
L
O.D.
C
1/8 3/16
D
1/4 1/4 5/16 3/8 3/8 1/2
TuBE
L
O.D.
D
1/4 3/8
C
CATAlOg NuMBEr C DI l
621x2 5/16 .094 0.25 0.66
621x3 3/8 .125 0.28 0.76
621x4 7/16 .188 0.31 0.79
621x5 1/2 .250 0.34 0.88
621x6 9/16 .312 0.38 0.97
621x8 11/16 .406 0.44 1.10
621x10 13/16 .500 0.50 1.25
MAlE PIPE CATAlOg ThrEAD NuMBEr C Dl
1/16 681x2x1 3/8 .094 0.78
1/8 681x2 7/16 .094 0.78
1/8 681x3 7/16 .125 0.84
1/8 681x4 7/16 .188 0.88
1/4 681x4x4 9/16 .188 1.06
1/8 681x5 1/2 .234 0.91
1/4 681x5x4 9/16 .250 1.09
1/8 681x6x2 9/16 .250 0.97
1/4 681x6 9/16 .312 1.17
3/8 681x6x6 11/16 .312 1.16
1/2 681x6x8 7/8 .312 1.34
1/4 681x8x4 11/16 .281 1.22
3/8 681x8 11/16 .406 1.22
1/2 681x8x8 7/8 .406 1.41
1/2 681x10 7/8 .500 1.50
FEM. PIPE CATAlOg ThrEAD NuMBEr C Dl
1/8 661x2 9/16 .094 0.75
1/8 661x3 9/16 .125 0.78
1/8 661x4 9/16 .188 0.78
1/4 661x4x4 11/16 .188 1.03
1/8 661x5 9/16 .250 0.81
1/8 661x6x2 9/16 .312 0.84
1/4 661x6 11/16 .312 1.06
3/8 661x8 13/16 .406 1.12
MAlE PIPE CATAlOg ThrEAD NuMBEr C Dl
1/8 631x4 7/16 .125 0.88
1/4 631x6 9/16 .219 1.16
Min. pressure 3 psi. Ball and spring position may be reversed to change flow/check direction. Ballcheck valves are neither tested nor adjusted prior to sale.

Brass Products
Selfalign
TuBE CATAlOg
Bulkhead union
L
O.D. NuMBEr C D I l MAx. P
I
1/4 741x4 9/16 .188 0.33 1.58 0.52
P D
C
Assembly with long nut 1741x.
TuBE CATAlOg
90° union Elbow
O.D. NuMBEr D M
1/4 651x4 .188 0.60
M
3/8 651x6 .312 0.73
D M
Assembly with long nut 1651x.
TuBE MAlE PIPE CATAlOg
90° Male Elbow N
O.D. ThrEAD NuMBEr D D1 M N
1/8 1/16 691x2x1 .109 .125 0.54 0.66 1/8 1/8 691x2 .094 .219 0.60 0.67
M
3/16 1/8 691x3 .125 .188 0.62 0.69 D1 1/4 1/8 691x4 .188 .219 0.62 0.75 1/4 1/4 691x4x4 .188 .219 0.62 0.75
D
5/16 1/8 691x5 .250 .250 0.62 0.75 5/16 1/4 691x5x4 .250 .312 0.69 0.84
Assembly with long nut 1691x.
3/8 1/8 691x6x2 .312 .234 0.69 0.69 3/8 1/4 691x6 .312 .344 0.75 0.94 3/8 3/8 691x6x6 .312 .438 0.84 0.94 3/8 1/2 691x6x8 .312 .531 1.06 1.12 1/2 1/4 691x8x4 .406 .312 0.84 0.94 1/2 3/8 691x8 .406 .406 0.94 1.12 1/2 1/2 691x8x8 .406 .531 0.94 1.31 5/8 1/2 691x10 .500 .562 1.06 1.31
TuBE FEM. PIPE CATAlOg
90° Female Elbow
O.D. ThrEAD NuMBEr D M N
3/16 1/8 701x3 .125 0.69 0.56
D 1/4 1/8 701x4 .188 0.69 0.56
M N
Assembly with long nut 1701x.

Brass Products
Selfalign
union Tee
Assembly with long nut 1641x.
Male run Tee
D
M
M
M
D
M
D1
M
N
Assembly with long nut 1711x.
Male Branch Tee
Assembly with long nut 1721x.
D1
DN
M
M
TuBE CATAlOg
O.D. NuMBEr D M
3/16 641x3 .125 0.60
1/4 641x4 .188 0.62
5/16 641x5 .250 0.60
3/8 641x6 .312 0.73
1/2 641x8 .406 0.94
TuBE MAlE PIPE CATAlOg D1
O.D. ThrEAD NuMBEr D OPT. M N
3/16 1/8 711x3 .125 .219 0.62 0.69
1/4 1/8 711x4 .188 .219 0.62 0.75
3/8 1/4 711x6 .312 .344 0.75 0.94
TuBE MAlE PIPE CATAlOg
O.D. ThrEAD NuMBEr D D1 M N
1/4 1/8 721x4 .188 .219 0.62 0.75
1/4 1/4 721x4x4x4 .188 .281 0.78 0.85
3/8 1/4 721x6 .312 .344 0.75 0.94
1/2 3/8 721x8 .406 .406 0.94 1.12

Refer to safety information regarding

Brass Products
proper selection of tubing and tube

Polyline Flareless connectors on page 1.
A

Size x46 x4 x5 x6 x8
Tube O.D. 1/4 1/4 5/16 3/8 1/2
Thread Size-B 3/8–24 3/8–24 7/16–24 1/2–24 11/16–20
Flow Dia. (D1) .078 .125 .141 .203 .312
Support Dia. (D2) .120 .166 .180 .245 .370

Typical Application:
Pneumatic instrumentation circuits, lubricant and cooling lines.
Pressure:
Working pressure up to 500 psi with a 4:1 safety factor depending on tubing. When using plastic tubing, use the working pressure for type used.
Vibration:
Excellent resistance.
Temperature Range:
When using compatible plastic tubing do not exceed the tubing temperature range. (Refer to tubing temperature range.)
Material:
CA360 Brass body, plastic sleeve.
Note:
Not recommended for use with PT230 or TP160 tubing.
Used With:
PT200 and PT240 plastic tubing. Not recommended for metal tubing. See pages 22-26 for material compatibility and pages 27-29 for plastic tubing.
Advantages:
No flaring of tubing required. Easy installation, captive sleeve, pre-assembled for installation and can be reassembled.
Conformance:
An exclusive product design. User approvals only.
How to Order:
Order 1/4" O.D. tubing with .040 wall, use suffix x4. Example: 1262x4. When .062 wall is desired, use suffix x46. Example: 1262x46.
Ordered as complete assemblies (body, nuts and sleeves) by catalog number. Nuts, sleeves and nut/sleeve assemblies can be ordered separately by catalog number.
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice.
Assembly Instructions:
1.
Cut tubing to desired length.

2.
Slide nut/sleeve assembly on tube. Threaded end “A” of nut must face toward connector.

3.
Bottom tubing into the connector.

4.
Tighten nut, hand tight.

Label Set:
FS-2100 (adhesive) CL-498 (non-adhesive)
Questions:
For additional technical questions, contact Technical Support at 1-888-258-0222.

Brass Products
Polyline Flareless
Plastic Sleeve
L
C
Brass Nut
L C
1/8" and 3/16" Nuts are flat Hex type.
Brass Nut/Plastic
L
Sleeve Assembly
C
Brass Bulkhead Nut
L
For use with 1274x Bulkhead Unions, ref. C page 55.
union
L L1
C
TuBE
O.D.
1/4
5/16
3/8
1/2
TuBE
O.D.
1/4
5/16
3/8
1/2
MTO - Made To Order
TuBE
O.D.
1/4
5/16
3/8
1/2
MTO - Made To Order
TuBE
O.D.
1/4
3/8
1/2
MTO - Made To Order
TuBE
O.D.
1/4
3/8
1/2
MTO - Made To Order
CATAlOg NuMBEr C l
1260x4 .259 0.34
1260x5 .321 0.39
1260x6 .384 0.41
1260x8 .509 0.44
CATAlOg DIA.
NuMBEr C l

1261x4 7/16 0.34
1261x5 1/2 0.34
1261x6 9/16 0.38
1261x8 13/16 0.44
CATAlOg DIA.
NuMBEr C l

1261x4A 7/16 0.43
1261x5A 1/2 0.45
1261x6A 9/16 0.49
1261x8A 13/16 0.46
CATAlOg NuMBEr C l
1202x4 9/16 0.19
1202x6 11/16 0.19
1202x8 7/8 0.19
CATAlOg NuMBEr C l l1
1262x4 3/8 1.00 0.69
1262x6 1/2 1.03 0.72
1262x8 11/16 1.28 0.84

Brass Products
Polyline Flareless
TuBE MAlE PIPE CATAlOg
Male Connector
L
O.D. ThrEAD NuMBEr C l l1
L1
1/4 1/16 1268x4x1 7/16 0.97 0.81
C
1/4 1/8 1268x4 7/16 0.97 0.81 1/4 1/4 1268x4x4 9/16 1.15 1.00 1/4 3/8 1268x4x6 11/16 1.18 1.03 5/16 1/8 1268x5w 7/16 0.97 0.81 5/16 1/4 1268x5x4 9/16 1.16 1.00 3/8 1/8 1268x6x2 1/2 1.00 0.84 3/8 1/4 1268x6 9/16 1.19 1.03 3/8 3/8 1268x6x6 11/16 1.19 1.03 1/2 1/4 1268x8x4 11/16 1.31 1.09 1/2 3/8 1268x8 11/16 1.31 1.09 1/2 1/2 1268x8x8 11/16 1.62 1.03
MTO - Made To Order
TuBE FEM. PIPE CATAlOg
Female Connector
L
O.D. ThrEAD NuMBEr C l l1
L1
1/4 1/8 1266x4 1/2 0.87 0.72
C
1/4 1/4 1266x4x4 5/8 1.09 0.93 3/8 1/4 1266x6 5/8 1.09 0.94
TuBE CATAlOg MAx.
Bulkhead union
L
O.D. NuMBEr C l l1 P
L1
1/4 1274x4 9/16 1.56 1.25 0.38
C
3/8 1274x6 11/16 1.68 1.38 0.47 1/2 1274x8
7/8 2.09 1.66 0.63
MTO - Made To Order
For Bulkhead Nuts, ref. page 54.
P

Brass Products
Polyline Flareless
Male Elbow N
M
M1
Female Elbow N
M M1
union Tee MM M1 M1
N1 N
Male run Tee MN M1
M M1
Male Branch Tee MM M1 M1
N
TuBE MAlE PIPE CATAlOg
O.D. ThrEAD NuMBEr M M1 N
1/4 1/16 1269x4x1 0.75 0.59 0.72 1/4 1/8 1269x4 0.75 0.59 0.72 1/4 1/4 1269x4x4 0.81 0.66 0.94 1/4 3/8 1269x4x6 0.84 0.69 1.08 5/16 1/8 1269x5 0.75 0.59 0.72 3/8 1/8 1269x6x2 0.88 0.66 0.75 3/8 1/4 1269x6 0.87 0.72 1.00 3/8 3/8 1269x6x6 0.87 0.72 1.08
MTO - Made To Order
TuBE FEM. PIPE CATAlOg
O.D. ThrEAD NuMBEr M M1 N
1/4 1/8 1270x4 0.87 0.66 0.56 1/4 1/4 1270x4x4 0.96 0.75 0.69 3/8 1/4 1270x6 0.86 0.75 0.69
MTO - Made To Order
TuBE CATAlOg
O.D. NuMBEr M M1 N N1
1/4 1264x4 0.75 0.59 0.75 0.59 3/8 1264x6 0.87 0.72 0.87 0.72
TuBE MAlE PIPE CATAlOg
O.D. ThrEAD NuMBEr M M1 N
1/4 1/8 1271x4 0.75 0.59 0.72 1/4 1/4 1271x4x4x4 0.81 0.66 0.94 3/8 1/4 1271x6 0.87 0.72 1.00
MTO - Made To Order
TuBE MAlE PIPE CATAlOg
O.D. ThrEAD NuMBEr M M1 N
1/4 1/8 1272x4 0.75 0.59 0.72 1/4 1/4 1272x4x4x4 0.81 0.66 0.94 3/8 1/4 1272x6 0.87 0.72 1.00 1/2 3/8 1272x8 1.06 0.84 1.12
MTO - Made To Order

Refer to safety information regarding

Brass Products Note:
proper selection of tubing and tube Push>Connect questions, contact connectors on page 1.
Technical Support at 1-888-258-0222.
For additional technical
Push>Connect

Push>Connect Metric

Typical Application:
Compressed air, pneumatic instrumentation, circuit, lubricant and cooling lines.
Pressure:
Up to 250 psi depending on tube size.
Sealing Method:
O-Ring of Buna-N Construction.
Temperature Range:

When using compatible plastic tubing do not exceed the tubing temperature range (Refer to tubing temperature range).
Material:
Brass, Nickel Plated.
NOMINAl SIzE 2
Vacuum:

Fittings rated at 29.5 inches of mercury vacuum.
Used With:
PT230 and TP160 nylon, and PT240 Polyethylene tubing. See pages 22-26 for material compatibility and pages 27-29 for plastic tubing.
Advantages:
Ease of assembly. No tools required, reusability of connectors and the time savings of assembly and disassembly.
Hex Dimensions:
All hexes are in inches.
How to Order:
Individually by catalog
number.

4 5MM 6
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice.
Assembly Instructions:
1.
To connect, simply push the tubing into the connector.

2.
To disconnect, depress the collet ring with two fingers and withdraw.

Label Set:
CL-499 (non-adhesive)
8

Thread
MM M5 x .8
BSPT 1/8 (2PT) 1/4 (4PT) 3/8 (6PT) 1/2 (8PT)
BSPP 1/8 (2PP) 1/4 (4PP) 3/8 (6PP) 1/2

Typical Application:
Compressed air, pneumatic instrumentation, circuit, lubricant and cooling lines.
Pressure:
Up to 250 psi depending on tube size.
Sealing Method:
O-Ring of Buna-N Construction.
Temperature Range:
-40°F to 200°F (-40°C to 93°C).
Material:
Brass, Nickel Plated.
Used With:
MTP160 nylon tubing. See pages 22-26 for material compatibility and pages 27-29 for plastic tubing.
Advantages:
Ease of assembly. No tools required, reusability of fittings and the time savings of assembly and disassembly.
Hex Dimensions:
All hexes are metric.
How to Order:
Individually by catalog number.
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice.
Assembly Instructions:
1.
To connect, simply push the tubing into the connector.

2.
To disconnect, depress the collet ring with two fingers and withdraw.

Suffix Chart:
MM -Metric Screw
Thread MMS -Metric Screw
Thread Swivel MRP -Metric Red Plug PP -British Parallel Plug PPS -British Parallel

Pipe Swivel PT -British Tapered Pipe PTS -British Tapered
Pipe Swivel

Brass Products

Push>Connect
Push>Connect
Flow Controls

Typical Application:

Compressed air, pneumatic instrumentation, circuit, lubricant and cooling lines. Also excellent for assembly equipment and cylinder control.
Pressure:
Up to 250 psi depending on tube size.
Sealing Method:
O-Ring of Buna-N Construction. (Viton available on request by special order.)
Temperature Range:
0°F to +160°F (-17.8°C to +71°C)
Material:
Brass, Nickel Plated.
Note:
For additional technical questions, contact Technical Support at 1-888-258-0222.
Used With:

PT230 and TP160 nylon, and PT240 Polyethylene tubing. See pages 22-26 for material compatibility and pages 27-29 for plastic tubing.
Advantages:

Ease of assembly. No tools required, reusability of connectors and the time savings of assembly and disassembly. These flow controls have a simple design, but offer excellent ability to control the speed of a cylinder or motor.
Hex Dimensions:
All hexes are in inches.
How to Order:
Individually by catalog number.

Refer to safety information regarding
proper selection of tubing and tube connectors on page 1.
Note:

Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice.
Assembly Instructions:
1.
To connect, simply push the tubing into the connector.

2.
To disconnect, depress the collet ring with two fingers and withdraw.

Brass Products
Push>Connect
Cartridge

B

Cartridge body is not Nickel-plated.
Plug
(Plastic)

Double union

Joins Push>Connect Fittings.
reducer

AB

TuBE CATAlOg
O.D. NuMBEr F g l S h B
1/8 1161x2 0.34 0.35 0.59 .344 .433 0.14
5/32 1161x2.5 0.34 0.35 0.57 .344 .433 0.14
1/4 1161x4 0.46 0.48 0.65 .470 .472 0.16
5/16 1161x5 0.54 0.56 0.67 .549 .551 0.25
3/8 1161x6 0.62 0.64 0.79 .627 .590 0.32
1/2 1161x8 0.74 0.76 0.83 .746 .629 0.42

g TuBE CATAlOg
O.D. NuMBEr l P T
1/8 1129x2 1.06 0.24 0.79
5/32 1129x2.5 1.14 0.32 0.79
1/4 1129x4 1.24 0.32 0.89
5/16 1129x5 1.36 0.47 0.96
3/8 1129x6 1.46 0.47 1.06
1/2 1129x8 1.59 0.63 1.12

TuBE CATAlOg
O.D. NuMBEr l
1/8 1105x2 1.28
5/32 1105x2.5 1.28
1/4 1105x4 1.40
5/16 1105x5 1.59
3/8 1105x6 1.81
1/2 1105x8 1.89

TuBE O.D. A TuBE O.D. B CATAlOg NuMBEr C F l T
1/8 1/4 1109x2x4 0.61 0.35 1.16 0.71
5/32 1/4 1109x2.5x4 0.61 0.35 1.16 0.71
1/4 3/8 1109x4x6 0.82 0.50 1.46 0.91
1/4 1/2 1109x4x8 0.68 0.50 1.32 0.91
3/8 1/2 1109x6x8 0.79 0.65 1.58 0.94

Brass Products

Push>Connect
Stem Adapter

union

Joins tubing.

Bulkhead union MAX

SW1
union “Y”

CATAlOg
TuBE MAlE NuMBEr
O.D. PIPE ThrEAD h T l SW (MM)
1/8 1/8 1180x2 0.37 0.65 1.20 12
1/8 1/4 1180x2x4 0.51 0.65 1.36 14
5/32 1/8 1180x2.5 0.37 0.65 1.20 12
5/32 1/4 1180x2.5x4 0.51 0.65 1.36 14
1/4 1/8 1180x4 0.37 0.71 1.26 12
1/4 1/4 1180x4x4 0.51 0.71 1.42 14
5/16 1/8 1180x5 0.37 0.81 1.36 12
5/16 1/4 1180x5x4 0.51 0.81 1.34 14
3/8 1/4 1180x6 0.51 0.91 1.61 17
3/8 3/8 1180x6x6 0.51 0.91 1.61 19
1/2 3/8 1180x8 0.51 0.94 1.65 19
1/2 1/2 1180x8x8 0.71 0.94 1.87 22

TuBE CATAlOg
O.D. NuMBEr F g l N
1/8 1162x2 0.33 0.35 1.14 0.55
5/32 1162x2.5 0.33 0.35 1.14 0.55
1/4 1162x4 0.46 0.47 1.32 0.64
5/16 1162x5 0.54 0.55 1.46 0.69
3/8 1162x6 0.61 0.66 1.61 0.79
1/2 1162x8 0.72 0.75 1.71 0.83

TuBE CATAlOg MAx SW
O.D. NuMBEr B F l N (MM) (MM) SW1 T
1/8 1174x2 M10x1 0.34 1.14 0.55 0.35 14 14 0.83
5/32 1174x2.5 M10x1 0.34 1.14 0.55 0.32 14 14 0.79
1/4 1174x4 M14x1 0.49 1.32 0.64 0.37 17 17 0.83
5/16 1174x5 M16x1 0.56 1.42 0.69 0.41 19 19 0.83
3/8 1174x6 M18x1 0.62 1.61 0.79 0.47 22 22 0.93
1/2 1174x8 M20x1 0.74 1.71 0.83 0.53 24 24 0.98

TuBE O.D. CATAlOg NuMBEr C F l M
1/8 1107x2 0.24 0.83 1.42 0.39
5/32 1107x2.5 0.24 0.83 1.34 0.39
1/4 1107x4 0.24 0.96 1.52 0.49

Brass Products

Push>Connect
Swivel Male “Y”

Swivel for installation purposes only.
Male Connector

Allen wrench use permits close quarter installation not possible with a standard wrench.
Female Connector

union Elbow
TuBE O.D. MAlE PIPE ThrEAD CATAlOg NuMBEr
1/8 10-32* 1108x2A
1/8 1/8 1108x2
5/32 1/8 1108x2.5
1/4 1/8 1108x4

*UNF Thread. Seals with nylon washer (included).
MAlE TuBE PIPE CATAlOg
O.D. ThrEAD NuMBEr C F

1/8 10-32* 1168x2A 0.26 0.35 0.41 0.18 0.85 9 2 1/8 1/8 1168x2 0.26 0.35 0.55 0.37 0.85 12 2 1/8 1/4 1168x2x4 0.39 0.35 0.63 0.51 0.98 14 2
SW1
5/32 10-32* 1168x2.5A 0.26 0.35 0.41 0.18 0.81 9 2 5/32 1/8 1168x2.5 0.26 0.35 0.55 0.37 0.81 12 2.5
5/32 1/4 1168x2.5x4 0.39 0.35 0.63 0.51 0.94 14 2.5
1/4 10-32* 1168x4A 0.27 0.46 0.55 0.18 0.91 12 2
1/4 1/8 1168x4 0.35 0.46 0.55 0.37 0.98 12 4
1/4 1/4 1168x4x4 0.44 0.46 0.63 0.51 1.08 14 4
1/4 3/8 1168x4x6 0.46 0.46 0.87 0.51 1.10 19 4
5/16 1/8 1168x5 0.45 0.54 0.63 0.37 1.14 14 5
5/16 1/4 1168x5x4 0.45 0.54 0.63 0.51 1.14 14 6
5/16 3/8 1168x5x6 0.45 0.54 0.87 0.51 1.14 19 6
3/8 1/8 1168x6x2 0.59 0.61 0.78 0.51 1.38 17 7
3/8 1/4 1168x6 0.59 0.61 0.78 0.51 1.38 17 7
3/8 3/8 1168x6x6 0.39 0.61 0.87 0.51 1.18 19 7
3/8 1/2 1168x6x8 0.47 0.61 1.00 0.71 1.26 22 7
1/2 3/8 1168x8 0.53 0.72 0.87 0.51 1.36 19 10
1/2 1/2 1168x8x8 0.53 0.72 1.00 0.71 1.36 22 10
*UNF Thread. Seals with nylon washer (included).
CATAlOg TuBE FEM. NuMBEr SW
O.D. PIPE ThrEAD C F g h l (MM)
1/8 1/8 1166x2 0.39 0.35 0.51 0.34 0.95 12
1/8 1/4 1166x2x4 0.55 0.35 0.65 0.47 1.10 15
5/32 1/8 1166x2.5 0.39 0.35 0.51 0.34 0.95 12
5/32 1/4 1166x2.5x4 0.55 0.35 0.65 0.47 1.10 15
1/4 1/8 1166x4 0.39 0.46 0.51 0.34 1.02 12
1/4 1/4 1166x4x4 0.54 0.47 0.65 0.47 1.18 15
3/8 1/4 1166x6 0.51 0.60 0.73 0.47 1.30 17

F M l
0.83 0.39 1.04
0.83 0.39 1.54
0.83 0.39 1.54
0.96 0.49 1.67

SW SW1 g h l (MM) (MM)
3/8 3/8 1166x6x6 0.55 0.60 0.79 0.49 1.34 17
TuBE O.D. CATAlOg NuMBEr C F M SW (MM)
1/8 5/32 1/4 5/16 3/8 1/2 1165x2 1165x2.5 1165x4 1165x5 1165x6 1165x8 0.14 0.14 0.16 0.20 0.26 0.32 0.35 0.35 0.50 0.55 0.65 0.77 0.69 0.69 0.79 0.89 1.04 1.12 8 8 9 11 13 15

Brass Products
Push>Connect TuBE O.D. MAlE PIPE ThrEAD CATAlOg NuMBEr C E F h M SW (MM) SW1 (MM)
1/8 10-32* 1169x2AS 0.24 0.53 0.39 0.18 0.83 9 8

Swivel Male Elbow

1/8 1/8 1169x2S 0.24 0.71 0.39 0.32 0.83 9 12 1/8 1/4 1169x2x4S 0.24 0.87 0.39 0.42 0.83 9 14 5/32 10-32* 1169x2.5AS 0.24 0.53 0.39 0.18 0.79 9 8 5/32 1/8 1169x2.5S 0.24 0.71 0.39 0.32 0.79 9 12 5/32 1/4 1169x2.5x4S 0.24 0.87 0.39 0.47 0.83 9 14 1/4 1/8 1169x4S 0.27 0.73 0.50 0.32 0.91 10 12

1/4 1/4 1169x4x4S 0.27 0.81 0.50 0.47 0.91 10 14
Swivel for installation purposes only. 1/4 3/8 1169x4x6S 0.29 0.87 0.50 0.47 0.93 12 19
5/16 1/8 1169x5S 0.30 0.77 0.59 0.32 0.98 12 12
5/16 1/4 1169x5x4S 0.30 0.85 0.59 0.47 0.98 12 14
5/16 3/8 1169x5x6S 0.30 0.87 0.59 0.47 0.98 12 19
3/8 1/8 1169x6x2S 0.34 0.75 0.64 0.32 1.10 14 14
3/8 1/4 1169x6S 0.34 0.89 0.69 0.47 1.12 14 14
3/8 3/8 1169x6x6S 0.34 0.91 0.69 0.47 1.12 14 19
3/8 1/2 1169x6x8S 0.34 1.04 0.69 0.61 1.12 14 22
1/2 1/4 1169x8x4S 0.39 0.95 0.77 0.47 1.22 17 14
1/2 3/8 1169x8S 0.39 0.95 0.77 0.47 1.22 17 19

1/2 1/2 1169x8x8S 0.39 1.12 0.77 0.61 1.22 17 22
*UNF Thread. Seals with nylon washer (included).
Male Elbow

TuBE MAlE CATAlOg O.D. PIPE NuMBEr ThrEAD C E F h M SW (MM)

1/4 1/8 1169x4 0.16 0.57 1/4 1/4 1169x4x4 0.16 0.47 3/8 1/4 1169x6 0.26 0.55 3/8 3/8 1169x6x6 0.26 0.51 0.50 0.50 0.65 0.65 0.47 0.47 0.47 0.47 0.79 0.79 1.04 1.04 9 9 13 13

TuBE CATAlOg SW
union Tee
O.D. NuMBEr C F l M (MM)

1/8 1164x2 0.14 0.35 1.38 0.69 8 5/32 1164x2.5 0.14 0.35 1.38 0.69 8 1/4 1164x4 0.16 0.50 1.57 0.79 9 5/16 1164x5 0.20 0.55 1.77 0.89 11 3/8 1164x6 0.26 0.65 2.09 1.04 13

1/2 1164x8 0.32 0.77 2.24 1.12 15

TuBE MAlE
Male run Tee Swivel
O.D. PIPE CATAlOg SW SW1 ThrEAD NuMBEr E F h l M (MM) (MM)
1/8 10-32* 1171x2AS 0.53 0.39 0.18 1.53 0.89 9 8
SW1

1/8 1/8 1171x2S 0.65 0.35 0.20 1.54 0.69 8 12 5/32 10-32* 1171x2.5AS 0.53 0.39 0.18 1.50 0.79 9 8 5/32 1/8 1171x2.5S 0.65 0.35 0.20 1.54 0.69 8 12 5/32 1/4 1171x2.5x4S 0.69 0.35 0.26 1.63 0.69 8 14 1/4 1/8 1171x4S 0.67 0.46 0.20 1.65 0.79 9 12

1/4 1/4 1171x4x4S 0.71 0.46 0.26 1.75 0.79 9 14
1/4 3/8 1171x4x6S 0.69 0.46 0.29 1.77 0.79 9 19
3/8 1/4 1171x6S 0.85 0.64 0.26 2.15 1.04 13 14
3/8 3/8 1171x6x6S 0.83 0.64 0.29 2.17 1.04 13 19
3/8 1/2 1171x6x8S 0.91 0.64 0.34 2.28 1.04 13 22
1/2 1/4 1171x8x4S 0.91 0.72 0.26 2.20 1.12 15 13
1/2 3/8 1171x8S 0.87 0.72 0.29 2.20 1.12 15 19
1/2 1/2 1171x8x8S 0.95 0.72 0.34 2.40 1.12 15 22

*UNF Thread. Seals with nylon washer (included).

Brass Products

Push>Connect
MAlE TuBE PIPE CATAlOg SW SW1
O.D. ThrEAD NuMBEr C E F h l (MM) (MM)
1/8 10-32* 1172x2AS 0.24 0.53 0.39 0.18 1.61 0.35 0.32
Male Branch Tee Swivel

1/8 1/8 1172x2S 0.14 0.59 0.35 0.32 1.38 0.32 0.47
5/32 10-32* 1172x2.5AS 0.24 0.53 0.39 0.18 1.57 0.35 0.32
5/32 1/8 1172x2.5S 0.14 0.59 0.35 0.32 1.38 0.32 0.47
5/32 1/4 1172x2.5x4S 0.14 0.63 0.35 0.47 1.38 0.32 0.55
1/4 1/8 1172x4S 0.16 0.60 0.50 0.32 1.57 0.35 0.47
1/4 1/4 1172x4x4S 0.16 0.65 0.50 0.47 1.57 0.35 0.55
1/4 3/8 1172x4x6S 0.16 0.65 0.50 0.47 1.57 0.35 0.75
3/8 1/4 1172x6S 0.26 0.77 0.65 0.47 2.09 0.51 0.55
3/8 3/8 1172x6x6S 0.26 0.77 0.65 0.47 2.09 0.51 0.75
3/8 1/2 1172x6x8S 0.26 0.79 0.65 0.61 2.09 0.51 0.87
1/2 1/4 1172x8x4S 0.32 0.80 0.77 0.47 2.24 0.59 0.55
1/2 3/8 1172x8S 0.32 0.80 0.77 0.47 2.24 0.59 0.75
1/2 1/2 1172x8x8S 0.32 0.83 0.77 0.61 2.24 0.59 0.87
Stud Manifolds

Stud Manifolds

A

Banjo

Female Banjo

*UNF Thread. Seals with nylon washer (included).
MAlE PIPE CATAlOg ThrEAD A NuMBEr 10-32* 1184x1xA 1/8 1184x1x2 3/8 1184x1x6 *UNF Thread. Seals with nylon washer (included). h 0.16 0.24 0.35 l 0.71 1.06 1.18 S (MM) 0.18 0.34 0.34 SW (MM) 0.32 0.55 0.75
MAlE PIPE ThrEAD A 1/4 CATAlOg NuMBEr 1185x2x4 h 0.32 l 1.79 SW (MM) 0.67

TuBE O.D. A CATAlOg NuMBEr C F M O V W
5/32 1/8 1/4 1/4 1181x2.5A 1181x2x2 1181x4x2 1181x4x4 0.20 0.32 0.35 0.43 0.35 0.39 0.50 0.50 0.75 0.89 0.98 1.06 0.35 0.57 0.57 0.57 0.20 0.39 0.39 0.52 0.35 0.55 0.55 0.71

FEMAlE PIPE ThrEAD B CATAlOg NuMBEr V O M W
10-32* 1183xAxA 10-32 0.35 0.41 0.35
1/8 1/4 3/8 1183x2x2 1183x4x4 1183x6x6 1/8 1/4 3/8 0.57 0.57 0.57 0.79 1.00 1.10 0.55 0.71 0.83

*UNF Thread. Seals with nylon washer (included).

Brass Products
Push>Connect Metric TuBE O.D. (MM) 5 CATAlOg NuMBEr 1161x5M F 9.60 g 10.0 l 15.5 S 9.750 h 11.5 B 3.5

6 1161x6M 11.8 12.2 16.5 11.95 12.0 4.0
Cartridge

8 1161x8M 13.8 14.2 18.0 13.95 14.0 6.0

TuBE O.D. (MM) CATAlOg NuMBEr l P T
4 1129x4MRP 29.0 8 20.0 5 1129x5MRP 29.5 8 20.5 6 1129x6MRP 31.5 8 22.5 8 1129x8MRP 34.5 12 24.5
Plug (plastic)

10 1129x10MRP 37.0 12 27.0
12 1129x12MRP 40.5 16 28.5

TuBE O.D. (MM) CATAlOg NuMBEr l
Double union

4 1105x4M 32.5 6 1105x6M 35.5
8 1105x8M 40.5
Joins Metric Push>Connect fittings.
10 1105x10M 46.0

TuBE O.D. TuBE O.D. CATAlOg
reducer
A (MM) B (MM) NuMBEr C F l T

4 6 1109x4Mx6M 15.5 9 29.5 18.0 6 8 1109x6Mx8M 18.0 13 34.0 20.5 6 10 1109x6Mx10M 20.5 13 36.5 23.0
AB
8 10 1109x8Mx10M 20.5 14 39.0 23.0 8 12 1109x8Mx12M 21.5 14 39.0 24.0

TuBE O.D. ThD. SIzE CATAlOg SW
Stem Adapter
(MM) BSPP D NuMBEr h T l (MM)

4 1/8 1180x4Mx2PP 5.5 16.5 27.8 12 5 1/8 1180x5Mx2PP 5.5 18.0 29.3 12 6 1/8 1180x6Mx2PP 5.5 18.0 29.3 12 6 1/4 1180x6Mx4PP 7.0 18.0 31.0 14
8 1/8 1180x8Mx2PP 5.5 20.5 31.8 12
8 1/4 1180x8Mx4PP 7.0 20.5 33.5 14
10 1/4 1180x10Mx4PP 7.0 23.0 36.0 14
10 3/8 1180x10Mx6PP 8.0 23.0 37.3 19
12 3/8 1180x12Mx6PP 8.0 24.0 38.3 19

TuBE O.D. (MM) CATAlOg NuMBEr F g l N
union

4 1162x4M 8.40 9 29.0 14.0 5 1162x5M 9.80 11 32.0 15.0 6 1162x6M 11.7 12 34.0 15.5
Joins metric tubing.
8 1162x8M 13.7 14 37.0 17.5
10 1162x10M 15.4 17 41.5 20.0
12 1162x12M 18.3 19 43.5 21.0
Brass Products
Push>Connect Metric TuBE CATAlOg O.D. (MM) NuMBEr 4 1174x4M B M10x1 F 8.40 l 29.0 N 14.5 MAx 10.5 SW (MM) 14 SW1 (MM) 14 T 20.0
5 1174x5M M12x1 9.80 31.0 15.0 10.5 17 17 20.0

Bulkhead union

6 1174x6M M14x1 11.7 33.0 16.0 10.5 17 17 20.0 8 1174x8M M16x1 13.7 36.0 17.5 11.5 19 19 21.0 10 1174x10M M18x1 15.4 41.5 20.0 13.0 22 22 23.5 12 1174x12M M20x1 18.3 43.5 21.0 14.5 24 24 25.0
union “Y”

TuBE CATAlOg O.D. (MM) NuMBEr F C l M
4 1107x4M 18.0 5.0 33.0 9.0 6 1107x6M 24.5 7.0 39.0 12.5 8 1107x8M 28.5 9.0 44.0 14.5 10 1107x10M 32.0 15.5 53.5 16.0

TuBE ThrEAD
Male “Y”
O.D. SIzE CATAlOg SW (MM) A BSP D NuMBEr F h M l (MM)
4 1/8 1108x4Mx2PT 18.0 5.5 9 38.0 12 6 1/8 1108x6Mx2PT 24.5 5.5 12.5 41.5 12
*M5x0.8 metric screw thread. Seals with nylon washer (included).

Male Connector TuBE ThrEAD
O.D. SIzE CATAlOg SW SW1 (universal BSPT/BSPP) (MM) A BSP D NuMBEr C F g h l (MM) (MM)

4 1/8 1168x4Mx2PT 3.8 8.80 13.2 5.5 18.0 12 2.5 4 1/4 1168x4Mx4PT 6.0 8.80 15.2 7.0 19.5 14 2.5 5 1/8 1168x5Mx2PT 3.8 9.80 13.2 5.5 19.0 12 3.0 5 1/4 1168x5Mx4PT 5.5 9.80 15.2 7.0 20.0 14 3.0 6 1/8 1168x6Mx2PT 5.0 11.7 13.2 5.5 20.5 12 4.0
Allen wrench use permits close quarter installation not possible with a standard
6 1/4 1168x6Mx4PT 5.5 11.7 15.2 7.0 21.0 14 4.0
wrench.
8 1/8 1168x8Mx2PT 7.5 13.7 15.2 5.5 25.0 14 5.0 8 1/4 1168x8Mx4PT 6.5 13.7 15.2 7.0 24.0 14 6.0
8 3/8 1168x8Mx6PT 6.5 13.7 20.5 8.0 23.5 19 6.0
10 1/4 1168x10Mx4PT 8.5 16.3 18.5 7.0 28.5 17 7.0
10 3/8 1168x10Mx6PT 5.5 16.3 20.5 8.0 25.5 19 8.0
10 1/2 1168x10Mx8PT 5.0 16.3 24.5 9.0 25.0 22 8.0
12 1/4 1168x12Mx4PT 10.5 18.3 20.5 7.0 31.5 19 7.0
12 3/8 1168x12Mx6PT 9.5 18.3 20.5 8.0 30.5 19 9.0
12 1/2 1168x12Mx8PT 6.0 18.3 24.5 9.0 27.0 22 10.0

Male Connector
TuBE

O.D. ThrEAD CATAlOg SW SW1 (MM) A SIzE NuMBEr C F g h l (MM) (MM)
5 M5* 1168x5Mx5MM 5.5 8.8 9.9 3.5 20.5 9 2

D
6 M5* 1168x6Mx5MM 5.5 11.7 13.2 3.5 21.5 12 2
*M5x0.8 metric screw thread. Seals with nylon washer (included).
installation not possible with a standard
wrench.
Allen wrench use permits close quarter
TuBE ThrEAD
O.D. SIzE CATAlOg SW (MM) A BSPP NuMBEr C F g h l (MM)

Female Connector (BSPP)
4 1/8 1166x4Mx2PP 10.0 9.0 13.0 7.5 24.0 12 4 M5* 1166x4Mx5MM 6.5 7.8 8.8 5.0 20.5 8 6 1/8 1166x6Mx2PP 10.0 11.7 13.0 7.5 26.0 12 6 1/4 1166x6Mx4PP 11.5 11.9 16.5 11.0 27.5 15 8 1/8 1166x8Mx2PP 9.5 13.7 15.2 7.5 27.0 14

8 1/4 1166x8Mx4PP 11.5 13.7 16.5 11.0 29.0 15
10 1/4 1166x10Mx4PP 11.5 15.7 18.5 11.0 31.5 17
*M5x0.8 is M profile thread. Seals with nylon washer (included).

Brass Products
Push>Connect
TuBE CATAlOg SWMetric O.D. (MM) NuMBEr C F M (MM)

4 1165x4M 3.5 9.0 17.5 8

union Elbow

5 1165x5M 6.0 11.0 21.0 9 6 1165x6M 4.0 12.7 20.0 9 8 1165x8M 5.0 14.0 22.5 11 10 1165x10M 6.5 16.5 26.5 13 12 1165x12M 7.5 19.5 28.5 15
TuBE ThrEAD

Male Elbow (universal BSPT/BSPP) O.D. A SIzE CATAlOg SW
(MM) BSP D NuMBEr C E F h M (MM)
4 1/8 1169x4Mx2PT 3.5 8.5 9.0 7.5 17.5 8
4 1/4 1169x4Mx4PT 6.0 11.5 10.0 12 20.0 9

F 5 1/8 1169x5Mx2PT 6.0 9.5 11.0 7.5 21.0 9 5 1/4 1169x5Mx4PT 6.0 10.5 11.0 11.0 21.0 9 6 1/8 1169x6Mx2PT 4.0 9.0 12.7 7.5 20.0 9 6 1/4 1169x6Mx4PT 4.0 11.5 12.7 12 20.0 9 8 1/8 1169x8Mx2PT 5.0 10.5 14.0 7.5 22.5 11

8 1/4 1169x8Mx4PT 5.0 11.5 14.0 12.5 22.5 11
8 3/8 1169x8Mx6PT 7.5 13.0 15.0 11.5 25.0 12
10 1/4 1169x10Mx4PT 6.5 13.0 16.5 12 26.5 13
10 3/8 1169x10Mx6PT 6.5 12.5 16.5 11.5 26.5 13
12 1/4 1169x12Mx4PT 7.5 14.5 19.5 12 28.5 15
12 3/8 1169x12Mx6PT 7.5 14.5 19.5 12.5 28.5 15

Male Elbow Swivel
TuBE ThrEAD
O.D. A SIzE CATAlOg SW SW1 (MM) BSP D NuMBEr C E F h M (MM) (MM)

(universal BSPT/BSPP)
4 1/8 1169x4Mx2PTS 3.5 14.5 9.0 5.5 17.5 8 12 4 1/4 1169x4Mx4PTS 3.5 14.5 9.0 7.0 17.5 8 14 5 1/8 1169x5Mx2PTS 6.0 14.5 11.0 5.5 21.0 9 12 5 1/4 1169x5Mx4PTS 6.0 14.5 11.0 7.0 21.0 9 14 6 1/8 1169x6Mx2PTS 4.0 15.0 12.7 5.5 20.0 9 12 6 1/4 1169x6Mx4PTS 4.0 15.0 12.7 7.0 20.0 9 14

8 1/8 1169x8Mx2PTS 5.0 16.0 14.0 5.5 22.5 11 12
Swivel for installation purposes only. 8 1/4 1169x8Mx4PTS 5.0 16.0 14.0 7.0 22.5 11 14
8 3/8 1169x8Mx6PTS 5.0 16.5 14.0 8.0 22.5 11 19
10 1/4 1169x10Mx4PTS 6.5 18.5 16.5 7.0 26.5 13 14
10 3/8 1169x10Mx6PTS 6.5 19.0 16.5 8.0 26.5 13 19
10 1/2 1169x10Mx8PTS 6.5 19.5 16.5 9.0 26.5 13 22
12 1/4 1169x12Mx4PTS 7.5 20.0 19.5 7.0 28.5 15 17
12 3/8 1169x12Mx6PTS 7.5 20.0 19.5 8.0 28.5 15 19
12 1/2 1169x12Mx8PTS 7.5 20.5 19.5 9.0 28.5 15 22

Male Elbow Swivel

TuBE
O.D. A ThrEAD CATAlOg SW SW1 (MM) SIzE NuMBEr C E F h M (MM) (MM)
4 M5* 1169x4Mx5MMS 6 12.5 11.0 4 21 9 8 5 M5* 1169x5Mx5MMS 4 13.0 12.7 4 20 9 10
*M5x0.8 metric screw thread. Seals with nylon washer (included).

Swivel for installation purposes only.

TuBE ThD.

Brass Products O.D. A SIzE CATAlOg SW SW1
(MM) BSP D NuMBEr C E F h l M (MM)(MM)

Push>Connect 4 1/8 1171x4Mx2PTS 3.5 14.5 9.0 5.5 37.5 17.5 8 12
Metric 5 1/8 1171x5Mx2PTS 6.0 14.5 11.0 5.5 41.0 21.0 9 12
5 1/14 1171x5Mx4PTS 6.0 14.5 11.0 7.0 42.5 21.0 9 14

6 1/8 1171x6Mx2PTS 4.0 15.0 12.7 5.5 40.0 20.0 9 12
Male run Tee Swivel (universal BSPT/BSPP)
6 1/4 1171x6Mx4PTS 4.0 15.0 12.7 7.0 41.5 20.0 9 14 8 3/8 1171x8Mx6PTS 5.0 16.5 14.0 8.0 47.0 22.5 13 19 10 1/4 1171x10Mx4PTS 6.5 18.5 16.5 7.0 52.0 26.5 13 14
F
10 3/8 1171x10Mx6PTS 6.5 18.5 16.5 8.0 53.5 26.5 15 19 12 3/8 1171x12Mx6PTS 7.5 19.5 19.5 8.0 56.5 28.5 16 19

Swivel for installation purposes only.

TuBE CATAlOg SW
union Tee
O.D. (MM) NuMBEr C F l M (MM)
4 1164x4M 3.5 9.0 35 17.5 8 5 1164x5M 6.0 11.0 42 21.0 9 6 1164x6M 4.0 12.7 40 20.0 9 8 1164x8M 5.0 14.0 45 22.5 11 10 1164x10M 6.5 16.5 53 26.5 13

12 1164x12M 7.5 19.5 57 28.5 15
TuBE

Male runTee Swivel O.D. A ThD. CATAlOg SW SW1 (MM) SIzE NuMBEr C E F h l M (MM) (MM)

4 M5* 1171x4Mx5MMS 3.5 12.5 9 4 34 17.5 8 8 5 M5* 1171x5Mx5MMS 6.0 12.5 11 4 37 21.0 9 8
*M5x0.8 metric screw thread. Seals with nylon washer (included).
F

Swivel for installation purposes only.
TuBE ThrEAD
Male Branch Tee Swivel O.D. A (MM) SIzE BSP D CATAlOg NuMBEr C E F h l SW SW1 (MM) (MM)
4 1/8 1172x4Mx2PTS 3.5 14.5 9.0 5.5 35 8 12
5 1/8 1172x5Mx2PTS 6.0 14.5 11.0 5.5 42 9 12
5 1/4 1172x5Mx4PTS 6.0 14.5 11.0 7.0 42 9 14
6 1/8 1172x6Mx2PTS 4.0 15.0 12.7 5.5 40 9 12
6 1/4 1172x6Mx4PTS 4.0 15.0 12.7 7.0 40 9 14
8 1/8 1172x8Mx2PTS 5.0 16.0 14.0 5.5 45 11 12
8 1/4 1172x8Mx4PTS 5.0 16.0 14.0 7.0 45 11 14
8 3/8 1172x8Mx6PTS 5.0 16.5 14.0 8.0 45 11 19
10 1/4 1172x10Mx4PTS 6.5 18.5 16.5 7.0 53 13 14
10 3/8 1172x10Mx6PTS 6.5 19.0 16.5 8.0 53 13 19
12 1/4 1172x12Mx4PTS 7.5 20.0 19.5 7.0 57 15 17
12 3/8 1172x12Mx6PTS 7.5 20.0 19.5 8.0 57 15 19
12 1/2 1172x12Mx8PTS 7.5 20.5 19.5 9.0 57 15 22

TuBE O.D. A (MM) ThrEAD SIzE CATAlOg NuMBEr C E F h l SW (MM) SW1 (MM)
F 4 M5* 1172x4Mx5MMS 3.5 14.5 9 4 35 8 8
*M5x0.8 metric screw thread. Seals with nylon washer (included).

Swivel for installation purposes only.

Brass Products Note: Note:
For additional technical We reserve the right to alter Push>Connect questions, contact these specifications without Technical Support at prior notice. Flow Controls 1-888-258-0222.
right Angle Technical Data Threads: Flow Control Valve: 10-32 UNF - 1/8 - 1/4 - 3/8 and Needle Valves Flow Regulator NPTF SCU-MCU Regulation: Tube Sizes:
Adjustable Screw 1/8 - 5/32 - 1/4 - 3/8
Material: Operating Pressures:
to 150 PSI

A
Brass; Nickel Plated

Seals: Nominal Diameter:
Buna-N 10-32 UNF = .059 - 1/8 = .078 1/4 = .157 - 3/8 = .275

A

Flow Control Air flow is determined with Valve Performance 85 PSI at the in port and with 70 PSI at the outlet
1.60
6.00

0.00
246 810 Number of Turns
Air flow (SCFM) from B to A With adjustment open 1.9 With adjustment closed 1.4

1.40 5.00
Flow (SCFM of Air)
1.20
1.00
0.80
0.60
0.40
Flow (SCFM of Air)
Flow (SCFM of Air)
4.00
3.00
2.00
1.000.20
0.00
12.00 25.00

20.00
15.00
10.00
5.00 10.00
8.00
6.00
4.00
Flow (SCFM of Air)
2.00
0.00

0.00
2 4 6 8 101214
Number of Turns

Air flow (SCFM) from B to A Air flow (SCFM) from B to A With adjustment open 15 With adjustment open 23 With adjustment closed 8 With adjustment closed 13

Brass Products

Push>Connect Flow Controls

Identification These unidirectional flow Coding of Banjo flow controllers
of flow control controllers have been
designed as small as M C U – 04 02

possible so as to be mounted directly on

valves or cylinders.

,

, Adjustment

Function
M=Manual U= unidirectional SCU S=Screwdriver

(flow control

MCU
, Assembly Port A
C=On cylinders
Thread B
CATAlOg TuBE B SW NuMBEr O.D. NPTF S h l (MM)
SCu
A555SCUx2.5A* 5/32 10-32 0.22 0.18 1.141 8 A55SCUx2.5x2 5/32 1/8 0.51 0.37 2.000 14 A55SCUx4x2 1/4 1/8 0.51 0.37 2.000 14

Port A
A55SCUx4x4 1/4 1/4 0.45 0.51 2.250 17 A55SCUx6x4 3/8 1/4 0.45 0.51 2.250 17

B A55SCUx6x6 3/8 3/8 0.48 0.51 2.440 19
Thread B *UNF Thread
BANjO
CATAlOg FEMAlE B SW
NuMBEr ThrEAD NPTF S h l (MM)
SCu
A557SCUx2x2 1/8 1/8 0.51 0.37 2.00 14 A557SCUx4x4 1/4 1/4 0.45 0.51 2.25 17

Port A
A557SCUx6x6 3/8 3/8 0.48 0.51 2.44 19
*UNF Thread

B

Thread B

BANjO CATAlOg FEMAlE B SW SW1 NuMBEr ThrEAD NPTF S h l z (MM) (MM)
MCu
A557MCUx2x2 1/8 1/8 0.51 0.37 2.38 2.56 14 7 A557MCUx6x6 3/8 3/8 0.48 0.51 2.95 3.25 19 10

Port A

B

Thread B

Brass Products Note:
For additional technical Push>Connect questions, contact Technical Support at Plus 1-888-258-0222.
Eaton is proud to announce Perfect thread seal: Super-quick Installations:
three design changes to A captured Teflon. ring New short thread length
Push>Connect products. around the base of the hex means fewer turns and
The introduction of a low shoulder, seals similar to super-quick installations.
profile, sure-seal design for a reusable (SAE type) seal Improved Swivel Design:
male NPTF threaded fittings eliminates thread sealant Strength and stability have
is here. Also, an improved and loose particles associ-been engineered into the
collet design will allow use ated with thread sealant. new male swivel.
with all types of tubing
from Nylon to 90A durom-Lower Profile: Universal Thread:

Push>Connect Plus has a Use with NPT, BSPP, and eter Polyurethane, including lower profile for those tight
Polyethylene, and PVC tub-places. A shorter thread BSPT ports. ing. Lastly, the male swivel design eliminates exposed The new part will have a design provides greater threads where dirt and ‘P’ in the part number to
strength and stability. bacteria can collect (ideal signify the new design. Below is a summary for food processing and An example of this change of features and ben-hygienic applications). is previous #1169x4S efits for the newly named becomes #1169Px4S.
More Versatility: Current Push>Connect

Push>Connect Plus. The new brass collet parts with 10-32UNF
is designed for use with threads and ending in ‘A’
all types of tubing from (eg.1168x2A) will continue
Nylon to 90A durometer with the current thread

Polyurethane, including design.
Polyethylene, and PVC
tubing.

Swivel Male “Y” CATAlOg TuBE MAlE NuMBEr

O.D. PiPE ThrEAD F h M l
1/8 1/8 1108Px2S 0.83 0.20 0.39 1.28 5/32 1/8 1108Px2.5S 0.83 0.20 0.39 1.28 1/4 1/8 1108Px4S 0.96 0.20 0.49 1.40
TuBE MAlE PiPE CATAlOg SW SW1
O.D. A ThrEAD D NuMBEr F g h l (MM) (MM)
Male Connector
1/8 10-32* 1168Px2A 0.346 0.411 0.177 0.846 9 2.0 1/8 1/8 1168Px2 0.346 0.551 0.200 0.728 12 2.5 1/8 1/4 1168Px2x4 0.346 0.629 0.255 0.807 14 2.5 5/32 10-32* 1168x2.5A 0.346 0.411 0.177 0.807 9 2.0 5/32 1/8 1168Px2.5 0.346 0.551 0.200 0.728 12 2.5 5/32 1/4 1168Px2.5x4 0.346 0.629 0.255 0.807 14 2.5 1/4 10-32* 1168x4A 0.460 0.551 0.177 0.905 12 2.0 1/4 1/8 1168Px4 0.460 0.551 0.200 0.807 12 4.0

D

1/4 1/4 1168Px4x4 0.460 0.629 0.255 0.846 14 4.0
1/4 3/8 1168Px4x6 0.460 0.866 0.294 0.885 19 4.0
5/16 1/8 1168Px5 0.539 0.629 0.200 0.945 14 5.0
5/16 1/4 1168Px5x4 0.539 0.629 0.255 0.945 14 6.0
5/16 3/8 1168Px5x6 0.539 0.866 0.294 0.924 19 6.0
3/8 1/8 1168Px6x2 0.610 0.776 0.200 1.082 17 5.0
3/8 1/4 1168Px6 0.610 0.776 0.255 1.102 17 7.0
3/8 3/8 1168Px6x6 0.610 0.866 0.294 0.945 19 7.0
3/8 1/2 1168Px6x8 0.610 1.004 0.335 0.984 22 7.0
1/2 3/8 1168Px8 0.720 0.866 0.294 1.161 19 10.0
1/2 1/4 1168Px8x4 0.720 0.866 0.255 1.161 19 7.0
1/2 1/2 1168Px8x8 0.720 1.004 0.335 1.062 22 10.0

*UNF Thread

Brass Products
Push>Connect Plus

MAlE
Swivel Male Elbow
TuBE PiPE CATAlOg SW SW1
O.D. ThD. NuMBEr C E F h M (MM) (MM)
1/8 1/8 1169Px2S 0.14 0.59 0.35 0.20 0.69 8 12 1/8 1/4 1169Px2x4S 0.14 0.63 0.35 0.26 0.69 8 14 5/32 1/8 1169Px2.5S 0.14 0.59 0.35 0.20 0.69 8 12 5/32 1/4 1169Px2.5x4S 0.14 0.63 0.35 0.26 0.69 8 14 1/4 1/8 1169Px4S 0.16 0.63 0.46 0.20 0.79 9 12 1/4 1/4 1169Px4x4S 0.16 0.65 0.46 0.26 0.79 9 14

Swivel for installation purposes only. 1/4 3/8 1169Px4x6S 0.16 0.65 0.46 0.29 0.79 9 19
5/16 1/8 1169Px5S 0.20 0.65 0.54 0.20 0.89 11 12
5/16 1/4 1169Px5x4S 0.20 0.69 0.54 0.26 0.89 11 14
5/16 3/8 1169Px5x6S 0.20 0.69 0.54 0.29 0.89 11 19
3/8 1/8 1169Px6x2S 0.26 0.75 0.64 0.20 1.04 13 14
3/8 1/4 1169Px6S 0.26 0.77 0.64 0.26 1.04 13 14
3/8 3/8 1169Px6x6S 0.26 0.77 0.64 0.29 1.04 13 19
3/8 1/2 1169Px6x8S 0.26 0.79 0.64 0.34 1.04 13 22
1/2 1/4 1169Px8x4S 0.32 0.81 0.72 0.26 1.12 15 17
1/2 3/8 1169Px8S 0.32 0.81 0.72 0.29 1.12 15 19
1/2 1/2 1169Px8x8S 0.32 0.83 0.72 0.36 1.12 15 22

Male run Tee Swivel

MAlE
TuBE O.D. PiPE ThD. CATAlOg NuMBEr C E F h l M SW SW1 (MM) (MM)
1/8 1/8 1171Px2S 0.14 0.59 0.35 0.20 1.46 0.69 8 12
5/32 1/8 1171Px2.5S 0.14 0.59 0.35 0.20 1.46 0.69 8 12
5/32 1/4 1171Px2.5x4S 0.14 0.63 0.35 0.26 1.57 0.69 8 14
1/4 1/8 1171Px4S 0.16 0.63 0.50 0.20 1.61 0.89 9 12
1/4 1/4 1171Px4x4S 0.16 0.65 0.50 0.26 1.70 0.79 9 14
1/4 3/8 1171Px4x6S 0.16 0.65 0.50 0.30 1.73 0.79 9 19
3/8 1/4 1171Px6S 0.26 0.77 0.65 0.26 2.07 1.04 13 14

Swivel for installation purposes only. 3/8 3/8 1171Px6x6S 0.26 0.77 0.65 0.30 2.11 1.04 13 19
3/8 1/2 1171Px6x8S 0.26 0.79 0.65 0.33 2.16 1.04 13 22
1/2 1/4 1171Px8x4S 0.32 0.81 0.77 0.26 2.18 1.12 15 17
1/2 3/8 1171Px8S 0.32 0.81 0.77 0.30 2.22 1.12 15 19
1/2 1/2 1171Px8x8S 0.32 0.83 0.77 0.33 2.28 1.12 15 22

MAlE

Male Branch Tee Swivel

TuBE PiPE CATAlOg SW SW1
O.D. ThD. NuMBEr C E F h l M (MM) (MM)

1/8 1/8 1172Px2S 0.14 0.59 0.35 0.20 1.38 8 12 5/32 1/8 1172Px2.5S 0.14 0.59 0.35 0.20 1.38 8 12 5/32 1/4 1172Px2.5x4S 0.14 0.63 0.35 0.26 1.38 8 14 1/4 1/8 1172Px4S 0.16 0.61 0.50 0.20 1.51 9 12 1/4 1/4 1172Px4x4S 0.16 0.65 0.50 0.26 1.51 9 14 B 1/4 3/8 1172Px4x6S 0.16 0.65 0.50 0.30 1.51 9 19 3/8 1/4 1172Px6S 0.26 0.77 0.65 0.26 2.09 13 14 3/8 3/8 1172Px6x6S 0.26 0.77 0.65 0.30 2.09 13 19

Swivel for installation purposes only. 3/8 1/2 1172Px6x8S 0.26 0.79 0.65 0.32 2.09 13 22 1/2 3/8 1172Px8S 0.32 0.81 0.77 0.30 2.24 15 19

Refer to safety information regarding

Brass Products Note:
proper selection of tubing and tube Mini-Barb questions, contact connectors on page 1.
Technical Support at 1-888-258-0222.
For additional technical

Common Dimensions of Barbed End.
Typical Application:
Temperature control circuits, test apparatus, lubricant, coolant lines, pneumatic circuits, vacuum and fluid systems.
Pressure:
Will withstand burst pressures of plastic tubing.
Vibration:
Excellent resistance.
Temperature Range:
Depends on tubing used.
Material:
CA360 Brass.
TuBiNg O.D. D E J
5/32 .062 .113 .380
*3/16 .078 .125 .500
1/4 .127 .189 .500
3/8 .196 .270 .500
1/2 .312 .395 .630

*No barb on 3/16” size.
Used With:
PT240 Polyethylene tubing. See pages 22-26 for material compatibility and pages 27-29 for plastic tubing.
Advantages:
Quick connecting - no tube preparation. Hand assembly. Low cost one-piece push-on design. Barbed lip provides safe, positive connection. Compact size permits use in extremely tight areas.
Conformance:
An exclusive item with Eaton. User approvals only.
How to Order:
Individually by catalog number.
Note:

Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice.
Assembly Instructions:
1.
Push the tubing over insert.

2.
Bottom the tubing against connector body.

Label Set:
FS-1000 (adhesive) CL-496 (non-adhesive)

Brass Products
Mini-Barb
Plug
L
C
Solder Connector
L
J1
D1 C
union
L
C
Male Connector
L
C
D1
D
Female Connector
L
C
Compression Connector
L
C C1
TuBiNg CATAlOg DiA.
O.D. NuMBEr C l
1/4 1073x4 0.31 0.75
3/8 1073x6 0.40 0.75
1/2 1073x8 0.53 0.88
MTO - Made To Order
TuBiNg SOlDEr CATAlOg DiA.
O.D. CONN. NuMBEr C D1 J1
l
1/4 1/4 1079x4x4 5/16 0.25 0.50 1.00
TuBiNg CATAlOg DiA.
O.D. NuMBEr C l
1/4x3/16* 1062x4x3 1/4 1.25
1/4 1062x4 1/4 0.81
1/4 1062x4L 1/4 1.25
3/8x1/4 1062x6x4 5/16 1.19
3/8 1062x6 5/16 1.19
1/2x1/4 1062x8x4 1/2 1.33
1/2x3/8 1062x8x6 1/2 1.33
1/2 1062x8 1/2 1.45
*No barb on 3/16" end. “L” Suffix designates long Union. MTO - Made To Order
TuBiNg MAlE PiPE CATAlOg D1
O.D. ThrEAD NuMBEr C D OPT. l
5/32 1/8 1068x2.5x2 7/16 0.06 0.19 0.98
1/4 1/16 1068x4x1 5/16 0.12 – 1.06
1/4 1/8 1068x4 7/16 0.12 0.19 1.06
1/4 1/4 1068x4x4 9/16 0.12 0.28 1.28
3/8 1/8 1068x6x2 7/16 0.19 – 1.09
3/8 1/4 1068x6 9/16 0.19 0.28 1.28
1/2 3/8 1068x8 11/16 0.31 – 1.38
TuBiNg FEM. PiPE CATAlOg
O.D. ThrEAD NuMBEr C l
1/4 1/8* 1066x4 1/2 1.00
1/4 1/4 1066x4x4 11/16 1.25
3/8 1/4 1066x6 11/16 1.25
*PTF Short Thread MTO - Made To Order
TuBiNg COMP. CATAlOg
O.D. TuBE SizE NuMBEr C C1 l
3/16* 1/4 1078x3x4 7/16 1/2 1.29
1/4 1/4 1078x4x4 7/16 1/2 1.29
*No Barb on 3/16" end
For replacement nuts and sleeves see page 42.

Brass Products
Mini-Barb

TuBiNg COMP. CATAlOg

MAx. ThrEAD
Bulkhead Compression
O.D. TuBE SizE NuMBEr
Kl P T
Connector
1/4 1/4 1067x4x4 7/16 1/2 0.88 1.66 0.19 5/16-24 UNF

For replacement compression nuts and sleeves, see page 42.
Bulkhead union

For replacement nuts and sleeves, see page 43.
union Elbow

TuBiNg O.D. ThrEAD T CATAlOg NuMBEr
K l MAx. P
1/4 5/16–24 UNF 1074x4 7/16 1.06 1.74 0.31
3/8 3/8–24 UNF 1074x6 1/2 1.06 1.74 0.31

TuBiNg O.D. CATAlOg NuMBEr M
1/4 1065x4 0.70
3/8 1065x6 0.67
1/2 1065x8 0.86

TuBiNg MAlE PiPE CATAlOg
90° Male Elbow
O.D. ThrEAD NuMBEr D1 M N

1/4 1/16 1069x4x1 .156 .670 .550 1/4 1/8 1069x4 .250 .720 .630 1/4 1/4* 1069x4x4 .312 .780 .650 3/8 1/8 1069x6x2 .250 .740 .590 3/8 1/4* 1069x6 .312 .780 .620 1/2 3/8* 1069x8 .406 .980 .810
*PTF Short Thread

TuBiNg FEM. PiPE CATAlOg
90° Female Elbow
O.D. ThrEAD NuMBEr M N
1/4 1/8 1070x4 .750 .580 3/8 1/8 1070x6x2 .780 .480 3/8 1/4 1070x6 .840 .800

Brass Products
Mini-Barb
TuBiNg CATAlOg
union Tee
O.D. NuMBEr M N M1
N 1/4 1064x4 0.70 0.70 0.70 3/8x3/8x1/4 1064x6x6x4 0.70 0.74 0.70 3/8 1064x6 0.68 0.67 0.68
M M1
3/8x1/2x3/8 1064x6x8x6 0.67 0.73 0.79 1/2x1/2x1/4 1064x8x8x4 0.82 0.80 0.82 1/2x1/2x3/8 1064x8x8x6 0.79 0.73 0.79 1/2 1064x8 0.86 0.86 0.86
TuBiNg MAlE PiPE CATAlOg
Male run Tee
L
O.D. ThrEAD NuMBEr D1 l M N
N
1/4 1/8 1071x4 .188 1.21 0.71 0.59
*PTF Short Thread
M D1
TuBiNg MAlE PiPE CATAlOg
Male Branch Tee
D1
O.D. ThrEAD NuMBEr D1 M N
N 1/4 1/8 1072x4 .188 .720 .590 3/8 1/8 1072x6x2 .188 .720 .590 3/8 1/4 1072x6 .312 .780 .620
MM
TuBiNg FEMAlE PiPE CATAlOg
Female Branch Tee
O.D. ThrEAD NuMBEr M N
N 1/4 1/8 1077x4 0.77 0.48
M
TuBiNg M&F CATAlOg
Adapter Tee
L
O.D. PiPEThrEAD NuMBEr l M N
M
1/4 1/8* 1075x4 2.00 0.75 0.39
N
*PTF Special Short Thread

Refer to safety information regarding

Brass Products Note:
proper selection of tubing and tube Quick>Connect questions, contact connectors on page 1.
Technical Support at Air Brake 1-888-258-0222.
For additional technical

Typical Application:
Air brake systems except where temperatures exceed +200°F or where battery acid can drip on tubing. Not for fuel, water or oil.
Pressure:
Vacuum to 150 psi.
Vibration
Moderate vibration resistance.
Material:
CA360 Brass (Body & Collet).
EP (Ethylene Propylene) - o-ring.
Used With:
NT100 Nylon Tubing - SAE J844 Type A and B. See page 27 for NT100 Nylon Tubing data.
Temperature Range:
-40°F to +200°F (-40°C to +93°C)
Advantages:
Easy, fast assembly, one-piece fitting, reusable Field Serviceable (See collet repair kits, page 83).
Used With:
Polyon NT100 AirBrake Tubing
Conformance:
Meets D.O.T. FMVSS
571.106 and SAE J1131 air brake system performance requirements.
How to Order:
Order individually by catalog number (parts are standard with thread sealant).
Label Set:
FS-3300 (adhesive) CL-503 (non-adhesive)
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice. Additional information can be found in SAE J2494.
Assembly Instructions:
See following page.
Cartridge Information
Encapsulated:
For insertion into single bore cavity in substitution for pipe thread ports. Meets proposed SAE specifications for encapsulated press in style Air Brake connectors. Note: Encapsulated Cartridges are specifically designed for installation into a thermoplastic (Nylon/Glass filled Nylon/Acetal) or a soft metal (Aluminum/ Brass) cavity. For cavity dimensions contact Eaton Technical Support at 1-888-258-0222.
Four-Step Cartridge:
When you clean sheet a component design, the Four-Step Cartridge is an economical substitute for the encapsulated design. Special order only.
Select the design that is right for you. For applications where manifolds (manufactured from aluminum, plastic and brass) and air tanks (manufactured from steel and plastic composites) are used, contact Eaton Technical Support at 1-888-258-0222 for quotes based on your specific requirements and volumes.

Brass Products
Quick>Connect Air Brake
Assembly

Disassembly

Brass Products Note:
Use with NT100 Air Brake
Quick>Connect Tubing (SAE J844), Air Brake see page 27.
Encapsulated Cartridge

For design installation reference page 76 under Encapsulated heading.
union
(Ref. SAE No. AA0101)

NOTE: Joins tubing
Quick Connect Bulkhead union
(Ref. SAE No. AA0601)

TuBE CATAlOg DiA
O.D. NuMBEr F l D1 D h
5/32 1861x2.5 0.38 0.62 0.12 .165 0.17
D1 3/16 1861x3 0.44 0.62 0.12 .195 0.16
1/4 1861x4 0.56 0.65 0.13 .263 0.17
3/8 1861x6 0.69 0.81 0.22 .388 0.19
1/2 1861x8 0.81 0.83 0.34 .513 0.19
5/8 1861x10 0.97 0.99 0.40 .638 0.24
3/4 1861x12 1.12 0.99 0.52 .763 0.24

TuBE CATAlOg DiA
O.D. NuMBEr C l
5/32 1862x2.5 0.44 1.41
3/16 1862x3 0.44 1.62
1/4 1862x4 0.53 1.62
3/8 1862x6 0.69 1.94
1/2 1862x8 0.83 1.96
5/8 1862x10 0.96 2.51

C1
C
P

TuBE ThrEAD CATAlOg hEx hEx MAx
O.D. T NuMBEr C C1 l P
1/4 9/16–24 1874x4x4 5/8 11/16 1.62 0.47
3/8 3/4–16 1874x6x6 7/8 15/16 1.96 0.66
1/2 7/8–-14 1874x8x8 1 1 2.00 0.83

T 5/8 1–14 1874x10x10 1 1-1/4 2.42 1.00
Female Bulkhead union

C C1 FEMAlE
TuBE ThrEAD PiPE CATAlOg hEx hEx
O.D. T ThrEAD NuMBEr C C1 l
(Ref. SAE No. AA0603)
1/4 9/16–24 1/4 1873x4x4 5/8 11/16 1.45 3/8 3/4–16 3/8 1873x6x6 7/8 15/16 1.59 1/2 1–14 1/2 1873x8x8 1 1-1/4 1.97
T

Brass Products Note:
Use with NT100 Air Brake
Quick>Connect Air Brake
Male Connector
(Ref. SAE No. AA0102)

LL

Female Connector
(Ref. SAE No. AA0103)

45° Male Elbow
(Ref. SAE No. AA0302)

D1

Tubing (SAE J844), see page 27.
MAlE
TuBE O.D. PiPE ThrEAD CATAlOg NuMBEr C D1 l
5/32 1/16 1868x2.5x1 3/8 0.09 0.92
5/32 1/8 1868x2.5 7/16 0.25 0.92
3/16 1/8 1868x3 1/2 0.25 0.92
1/4 1/8 1868x4 9/16 0.19 0.95
1/4 1/4 1868x4x4 9/16 0.34 1.18
1/4 3/8 1868x4x6 11/16 0.41 1.17
3/8 1/8 1868x6x2 11/16 0.19 1.33
3/8 1/4 1868x6 11/16 0.31 1.29
3/8 3/8 1868x6x6 11/16 0.41 1.27
3/8 1/2 1868x6x8 7/8 0.53 1.47
1/2 1/4 1868x8x4 13/16 0.31 1.46
1/2 3/8 1868x8 13/16 0.41 1.35
1/2 1/2 1868x8x8 7/8 0.53 1.50
5/8 3/8 1868x10x6 1 0.41 1.72
5/8 1/2 1868x10 1 0.53 1.71
3/4 1/2 1868x12 1-1/16 0.53 1.72

FEMAlE
TuBE O.D. PiPE ThrEAD CATAlOg NuMBEr
l
1/4 1/8 1866x4 9/16 1.33
1/4 1/4 1866x4x4 11/16 1.58
3/8 1/8 1866x6x2 11/16 1.45
3/8 1/4 1866x6 11/16 1.69
3/8 3/8 1866x6x6 13/16 1.75
1/2 1/4 1866x8x4 13/16 1.66
1/2 3/8 1866x8 13/16 1.73
1/2 1/2 1866x8x8 1 1.97

MAlE
TuBE O.D. PiPE ThrEAD CATAlOg NuMBEr D1 M N
1/4 1/8 1880x4 0.19 0.95 0.59
1/4 1/4 1880x4x4 0.31 0.95 0.59
3/8 1/8 1880x6x2 0.25 1.05 0.48
3/8 1/4 1880x6 0.31 1.05 0.69
3/8 3/8 1880x6x6 0.41 1.10 0.63
3/8 1/2 1880x6x8 0.53 1.20 0.70
1/2 1/4 1880x8x4 0.31 1.20 0.87
1/2 3/8 1880x8 0.41 1.10 0.73
1/2 1/2 1880x8x8 0.53 1.10 0.76
5/8 3/8 1880x10x6 0.41 1.25 0.82
5/8 1/2 1880x10 0.53 1.39 0.90
3/4 1/2 1880x12 0.53 1.26 0.98

Brass Products Note:
Use with NT100 Air Brake
Quick>Connect Tubing (SAE J844), Air Brake see page 27.
45° Elbow - Swivel Male MAlE
TuBE PiPE CATAlOg
C
O.D. ThrEAD NuMBEr D1 M N
(Ref. SAE No. AA03DD)
1/4 1/8 1880x4S 0.13 0.82 0.60 7/16
M
D1 1/4 1/4 1880x4x4S 0.22 0.98 0.60 9/16 3/8 1/8 1880x6x2S 0.13 1.20 0.68 7/16
C
3/8 1/4 1880x6S 0.22 1.20 0.89 9/16 3/8 3/8 1880x6x6S 0.30 1.20 0.97 11/16 1/2 1/4 1880x8x4S 0.22 1.20 1.20 9/16 1/2 3/8 1880x8S 0.30 1.04 1.07 11/16 1/2 1/2 1880x8x8S 0.42 1.08 1.22 7/8
N
Swivel for installation purposes only.
TuBE CATAlOg
90° union Elbow
O.D. NuMBEr M
(Ref. SAE No. AA0201)
M 1/4 1865x4 0.93 3/8 1865x6 1.15 1/2 1865x8 1.24
M
MAlE
90° Male Elbow
TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M N
(Ref. SAE No. AA0302)
5/32 1/16 1869x2.5x1 0.13 0.75 0.59
M
5/32 1/8 1869x2.5 0.19 0.75 0.59 3/16 1/8 1869x3 0.19 0.84 0.69
D1
1/4 1/8 1869x4 0.19 0.92 0.68 1/4 1/4 1869x4x4 0.31 0.92 0.81
N
1/4 3/8 1869x4x6 0.41 1.03 0.82 3/8 1/8 1869x6x2 0.19 1.08 0.80 3/8 1/4 1869x6 0.31 1.13 0.96 3/8 3/8 1869x6x6 0.41 1.06 0.98 3/8 1/2 1869x6x8 0.53 1.27 1.07 1/2 1/4 1869x8x4 0.31 1.23 1.00 1/2 3/8 1869x8 0.41 1.25 0.98 1/2 1/2 1869x8x8 0.53 1.25 1.11 5/8 3/8 1869x10x6 0.41 1.44 1.09 5/8 1/2 1869x10 0.53 1.48 1.22
MAlE
90° Male Elbow long
TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M N
3/8 1/4 1869x6L 0.31 1.21 1.55
M D1
N

Brass Products Note:
Use with NT100 Air Brake
Quick>Connect Tubing (SAE J844), Air Brake see page 27.
MAlE
90° Swivel Male Elbow
TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M N C
(Ref. SAE No. AA02DD)
1/4 1/8 1869x4S 0.13 0.89 0.88 7/16 1/4 1/4 1869x4x4S 0.22 0.99 1.06 9/16 D1 1/4 3/8 1869x4x6S 0.30 0.98 1.06 11/16 3/8 1/8 1869x6x2S 0.13 1.03 0.97 7/16
M
C
3/8 1/4 1869x6S 0.22 1.10 1.14 9/16
N
3/8 3/8 1869x6x6S 0.30 1.12 1.15 11/16 3/8 1/2 1869x6x8S 0.42 1.18 1.40 7/8
Swivel for installation purposes only. 1/2 1/4 1869x8x4S 0.22 1.08 1.20 9/16 1/2 3/8 1869x8S 0.30 1.13 1.27 11/16 1/2 1/2 1869x8x8S 0.42 1.20 1.47 7/8 5/8 3/8 1869x10x6S 0.42 1.35 1.34 11/16 5/8 1/2 1869x10S 0.42 1.38 1.54 7/8
90° Female Elbow FEMAlE
TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr M N
(Ref. SAE No. AA0203)
1/4 1/8 1870x4 1.03 0.83 1/4 1/4 1870x4x4 1.04 0.78 3/8 1/8 1870x6x2 1.13 0.96 3/8 1/4 1870x6 1.28 1.09
M N
3/8 3/8 1870x6x6 1.21 1.07 1/2 1/4 1870x8x4 1.25 1.11 1/2 3/8 1870x8 1.22 1.11 1/2 1/2 1870x8x8 1.33 1.07
TuBE CATAlOg
union Tee
O.D. NuMBEr M
(Ref. SAE No. AA0401) M
1/4 1864x4 0.93 3/8 1864x6 1.15 1/2 1864x8 1.22
M M
N MAlE
Male run Tee
TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M M1 N
(Ref. SAE No. AA0424)
M1 1/4 1/8 1871x4 0.19 0.93 0.93 0.64 1/4 1/4 1871x4x4 0.19 0.93 0.94 0.82
D1
3/8 1/4 1871x6 0.31 1.14 1.14 0.91 3/8 3/8 1871x6x6 0.41 1.15 1.15 0.91 3/8x1/4 1/4 1871x6x4x4 0.31 1.14 1.07 0.96 3/8 1/2 1871x6x8 0.53 1.09 1.08 1.11 1/2 3/8 1871x8 0.41 1.09 1.10 1.22
M

Brass Products Note:
Use with NT100 Air Brake

Quick>Connect Tubing (SAE J844), Air Brake see page 27.
Swivel Male run Tee
(Ref. SAE No. AA04EE)
Swivel for installation purposes only.
Male Branch Tee
(Ref. SAE No. AA0425)
Swivel Male Branch Tee
(Ref. SAE No. AA04FF)
Swivel for installation purposes only.
Female Branch Tee

M N
M1 D1
C
D1
M1
M
N
D1
M
M1
C
N
N
MM
MAlE TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M M1 N
1/4 1/8 1871x4S 0.13 0.92 0.92 0.82 7/16
1/4 1/4 1871x4x4S 0.22 0.93 0.92 1.07 9/16
3/8 1/4 1871x6S 0.22 1.15 1.15 1.20 9/16
3/8 3/8 1871x6x6S 0.30 1.15 1.15 1.20 11/16
1/2 1/4 1871x8x4S 0.22 1.21 1.18 1.22 9/16
1/2 3/8 1871x8S 0.30 1.21 1.23 1.34 11/16
1/2 1/2 1871x8x8S 0.42 1.21 1.19 1.42 7/8
MAlE TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M M1 N
3/16 1/8 1872x3 0.19 0.75 0.74 0.64
1/4 1/8 1872x4 0.19 0.93 0.93 0.64
1/4 1/4 1872x4x4 0.19 0.93 0.93 0.82
3/8 1/4 1872x6 0.31 1.15 1.15 0.91
3/8 3/8 1872x6x6 0.31 1.15 1.15 0.92
1/2 1/4 1872x8x4 0.31 1.22 1.22 0.98
1/2 3/8 1872x8 0.41 1.24 1.24 0.99
1/2 1/2 1872x8x8 0.53 1.22 1.22 1.12
MAlE TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M M1 N
1/4 1/8 1872x4S 0.13 0.93 0.93 0.80 7/16
1/4 1/4 1872x4x4S 0.22 0.93 0.93 1.04 9/16
3/8 1/8 1872x6x2S 0.13 1.15 1.15 0.94 7/16
3/8 1/4 1872x6S 0.22 1.15 1.15 1.14 9/16
3/8 3/8 1872x6x6S 0.30 1.15 1.15 1.17 11/16
1/2 1/4 1872x8x4S 0.22 1.23 1.23 1.21 9/16
1/2 3/8 1872x8S 0.30 1.24 1.24 1.24 11/16
1/2 1/2 1872x8x8S 0.42 1.21 1.19 1.42 7/8
FEMAlE TuBE PiPE CATAlOg
O.D. ThrEAD NuMBEr M N
3/8 1/4 1877x6 1.16 0.78

Brass Products Note:
Use with NT100 Air Brake Quick>Connect Tubing (SAE J844), Air Brake see page 27.
MAlE FEMAlE TuBE PiPE PiPE CATAlOg
Adapter Tee

O.D. ThrEAD ThrEAD NuMBEr D1 M N M1

3/8 3/8 1/4 1883x6x6x4 0.41 1.28 1.00 0.95

D1

TuBE CATAlOg
Plugs, Pressure (Nylon)
O.D. NuMBEr
1/4 1829x4 3/8 1829x6 1/2 1829x8

The Collet Service Tool,
1800T made from sturdy plated steel, is designed to assist in field servicing O-Rings of Q-CAB fittings. Use the half moon radius section to pry up and remove the collet
Collet Service Tool

The 1800TRK tube release
1800TrK kit is designed to ease the removal of tubing from Q-CAB connectors. The individual tools are manufactured of a sturdy engineer-
Tube release Kit
and use the movable piano wire to remove the O-Ring. Notches are used to mark the tubing with insertion depth in five tubing sizes.
ing plastic. All seven tube sizes currently offered in QCAB can be serviced with the five tools that make up the 1800TRK kit.

Collet repair Kits TuBE O.D. rEPAir KiT PArT # Consisting of a replacement collet and a replacement provide an opportunity to repair damaged Q-CAB con
5/32 1800Kx2.5 o-ring, the collet repair kits nectors.
3/16 1800Kx3
1/4 1800Kx4
3/8 1800Kx6
1/2 1800Kx8
5/8 1800Kx10
3/4 1800Kx12

Refer to safety information regarding

Brass Products Note:
proper selection of tubing and tube Air Brake – questions, contact connectors on page 1.
Technical Support at Nylon Tubing 1-888-258-0222.
For additional technical
A

"A" Dim .
Thread Size-B

Tube O.D. 1/4 3/8 1/2 5/8 3/4
Thread Size-B 7/16–24 17/32–24 11/16–20 13/16–18 1–18
Typical Application:
Air brake systems except where temperatures exceed +200°F or where battery acid can drip on tubing.
Pressure:
Maximum operating pressure of 150 psi.
Vibration:
Fair resistance.
Temperature Range:
-40°F to +200°F (-40°C to +93°C)
Material:
CA360 Brass.
Used With:
NT100 Nylon Tubing - SAE J844 Type A and B. See page 27 for NT100 ylon Tubing data.
Advantages:
Easy to assemble (no tube preparation or flaring required.) Built in tube support. May be used with copper tubing by replacing nut, sleeve and insert with long nut and spherical sleeve. Insert should be removed for copper tubing use. See page 90 for details.
Conformance:
Meets specifications and standards of SAE and DOT FMVSS 571.106.
How to Order:
For complete assemblies (body, nuts and sleeves), order by catalog number. Example: 1468x4x4. To order body only (less nut and sleeve), add prefix “B” to catalog number and change “14” to “13”. Example: B1368x4x4. Nuts, sleeve and insert can be ordered separately by catalog number.
To order complete assembly with pipe sealant (Seal-A-Thread), add suffix “Z” to catalog number. Example: 1468x4x4Z (special order only).
To order complete assembly with gauge ring, add suffix “K” to catalog number. Example: 1468x4x4K (special order only).
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice. Additional information can be found in SAE J246.
Assembly Instructions:
1.
Cut tubing to desired length.

2.
Slide nut and then sleeve on tubing. Threaded end of nut “A” must face toward connector body.

3.
Insert tubing into the pre assembled fitting. Be sure tubing is bottomed in connector.

4.
Tighten nut to required torque as indicated on chart. Another check on proper assembly is dimension A also noted on chart. A gauge ring also assures installation to specification. See page 89.

TuBE A SizE TOrQuE DiMENSiON
1/4 85 to 115 in. lbs. .085/.105
3/8 12 to 17 ft. lbs. .125/.145
1/2 25 to 33 ft. lbs. .100/.120
5/8 26 to 35 ft. lbs. .115/.135
3/4 38 to 50 ft. lbs. .180/.200

Disassembly:
Remove nut and pull tubing out of connector body. Insert will remain in tubing.
Reassembly:
Push tubing and insert into connector body until it bottoms. Thread nut onto connector body and torque as in Step 4.
Label Set:
FS-900 (adhesive) CL-497 (non-adhesive)

Brass Products Note:
Use with NT100 Air Brake
Air Brake – Tubing (SAE J844), Nylon Tubing see page 27.

TuBE E
O.D. TuBE STOP h* D
1/4 0.20 0.32 .133 3/8 0.26 0.42 .215 1/2 0.39 0.45 .340 5/8 0.39 0.48 .398 3/4 0.51 0.50 .523
*H is hand tight dimensions.

TuBE CATAlOg DiA.
Sleeve
O.D. NuMBEr C D l
(Ref. SAE No. 100115)
1/4 1460x4 .359 .256 .300 3/8 1460x6 .479 .384 .390 1/2 1460x8 .625 .509 .430 5/8 1460x10 .745 .635 .480 3/4 1460x12 .922 .760 .530

TuBE CATAlOg
Nut
O.D. NuMBEr

Dl
(Ref. SAE No. 100110)
1/4 1461x4 9/16 .256 .450 3/8 1461x6 5/8 .384 .630 1/2 1461x8 13/16 .509 .720 5/8 1461x10 15/16 .634 .770 3/4 1461x12 1-1/8 .760 .810

TuBE CATAlOg
union
O.D. NuMBEr

l
(Ref. SAE No. 100101BA)
1/4 1462x4 7/16 0.85 3/8 1462x6 9/16 1.10 1/2 1462x8 11/16 1.31 5/8 1462x10 13/16 1.43 3/4 1462x12 1 1.60

Brass Products
Air Brake – Nylon Tubing
Male Connector
L
C
(Ref. SAE No. 100102BA)
D1
L
Female Connector
C
(Ref. SAE No. 100103BA)
Bulkhead union
L
C
P
45° Male Elbow
D1
(Ref. SAE No. 100302BA)
N
M
45°
Note:
Use with NT100 Air Brake Tubing (SAE J844), see page 27.
TuBE O.D. MAlE PiPE ThrEAD CATAlOg NuMBEr C D1 l
1/4 1/16 1468x4x1 7/16 .125 .90
1/4 1/8 1468x4 7/16 .188 .88
1/4 1/4 1468x4x4 9/16 .188 1.09
1/4 3/8 1468x4x6 11/16 .188 1.12
3/8 1/8 1468x6x2 9/16 .188 1.02
3/8 1/4 1468x6 9/16 .312 1.20
3/8 3/8 1468x6x6 11/16 .312 1.23
3/8 1/2 1468x6x8 7/8 .312 1.42
1/2 1/4 1468x8x4 11/16 .312 1.32
1/2 3/8 1468x8 11/16 .406 1.32
1/2 1/2 1468x8x8 7/8 .406 1.51
1/2 3/4 1468x8x12 1-1/16 .406 1.57
5/8 3/8 1468x10x6 13/16 .406 1.38
5/8 1/2 1468x10 7/8 .531 1.57
5/8 3/4 1468x10x12 1-1/16 .750 1.63
3/4 1/2 1468x12 1 .531 1.67
3/4 3/4 1468x12x12 1-1/16 .660 1.70

TuBE FEM. PiPE CATAlOg l
O.D. ThrEAD NuMBEr C
1/4 1/8 1466x4 9/16 0.85
3/8 1/8 1466x6x2 9/16 1.01
3/8 1/4 1466x6 11/16 1.19
3/8 3/8 1466x6x6 7/8 1.19
1/2 3/8 1466x8 7/8 1.28
MTO - Made To Order
TuBE CATAlOg MAx.
O.D. NuMBEr C l P
1/4 1474x4 9/16 1.38 0.25
3/8 1474x6 11/16 1.62 0.25
1/2 1474x8
13/16 1.88 0.25
MTO - Made To Order
TuBE MAlE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M N
1/4 1/8 1480x4 .188 0.50 0.64
1/4 1/4 1480x4x4 .312 0.61 0.86
3/8 1/4 1480x6 .312 0.72 0.86
3/8 3/8 1480x6x6 .406 0.76 0.95
1/2 1/4 1480x8x4 .312 0.85 0.95
1/2 3/8 1480x8 .406 0.85 0.95
1/2 1/2 1480x8x8 .531 0.88 1.17
5/8 1/2 1480x10 .531 0.94 1.17

Brass Products Note:
Use with NT100 Air Brake Air Brake – Tubing (SAE J844),
Nylon Tubing
union Elbow
(Ref. SAE No. 100201BA)
M
90° Male Elbow
(Ref. SAE No. 100202BA)
90° Male Elbow - long
(Ref. SAE No. 100202BA)
90° Female Elbow
(Ref. SAE No. 100203BA)
see page 27.
TuBE
O.D.
1/4
3/8
1/2
5/8

MTO - Made To Order
CATAlOg NuMBEr M
1465x4 0.63
1465x6 0.80
1465x8 0.94
1465x10 1.10

M D1
M
D1
M
N
M
TuBE
O.D.
1/4
N 1/4 1/4 3/8 3/8 3/8 3/8 1/2 1/2 1/2 5/8 5/8 5/8 3/4

TuBE
O.D.
3/8 N 1/2

TuBE
O.D.
1/4 3/8 1/2
MAlE PiPE CATAlOg ThrEAD NuMBEr D1 M N
1/8 1469x4 .188 0.63 0.67
1/4 1469x4x4 .312 0.69 0.88
3/8 1469x4x6 .406 0.74 0.87
1/8 1469x6x2 .188 0.73 0.75
1/4 1469x6 .312 0.80 0.93
3/8 1469x6x6 .406 0.85 0.92
1/2 1469x6x8 .531 0.95 1.11
1/4 1469x8x4 .312 0.87 1.00
3/8 1469x8 .406 0.94 1.00
1/2 1469x8x8 .531 1.04 1.19
3/8 1469x10x6 .406 1.01 1.06
1/2 1469x10 .531 1.10 1.25
3/4 1469x10x12 .750 1.21 1.25
1/2 1469x12 .531 1.20 1.34

MAlE PiPE CATAlOg
ThrEAD
14
3/8
FEM. PiPE ThrEAD
1/8
1/4
3/8
NuMBEr D1 M N
1469x6L .312 0.80 1.44
1469x8L .406 0.94 1.38
CATAlOg NuMBEr M N
1470x4 0.70 0.54
1470x6 0.90 0.78
1470x8 1.04 0.83

MTO - Made To Order

Brass Products Note:
Use with NT100 Air Brake Air Brake – Tubing (SAE J844),
Nylon Tubing see page 27.
union Tee TuBE CATAlOg
O.D. NuMBEr M M1 M2
(Ref. SAE No. 100401BA) M2 1/4 1464x4 0.63 0.63 0.63 3/8x3/8x1/4 1464x6x6x4 0.72 0.72 0.69 3/8 1464x6 0.80 0.80 0.80
MM1
1/2x1/2x3/8 1464x8x8x6 0.86 0.86 0.85 1/2 1464x8 0.94 0.94 0.94
Dimensions read left, right, center.
Male Branch Tee TuBE MAlE PiPE CATAlOg D1 O.D. ThrEAD NuMBEr D1 M M1 N
(Ref. SAE No. 100425BA) N 1/4 1/8 1472x4 .188 0.63 0.63 0.67 3/8x1/4 1/4 1472x6x4x4 .312 0.80 0.69 0.93 3/8 1/8 1472x6x6x2 .188 0.73 0.73 0.75 MM1 3/8 1/4 1472x6 .312 0.80 0.80 0.93 3/8 3/8 1472x6x6x6 .406 0.85 0.85 0.92 1/2x3/8 3/8 1472x8x6x6 .406 0.94 0.85 1.00 1/2 1/4 1472x8x8x4 .312 0.87 0.87 1.00 1/2 3/8 1472x8 .406 0.94 0.94 1.00 MTO - Made To Order
TuBE FEM. PiPE CATAlOg Female Branch Tee MM O.D. ThrEAD NuMBEr M N
N 3/8 1/4 1477x6 0.90 0.78 1/2 1/4 1477x8x8x4 0.97 0.83 5/8 1/4 1477x10x10x4 1.04 0.89
MTO - Made To Order
Male run Tee TuBE MAlE PiPE CATAlOg
O.D. ThrEAD NuMBEr D1 M M1 N
(Ref. SAE No. 100424BA) 1/4 1/8 1471x4 .188 0.64 0.64 0.67 M1 3/8x1/4 1/4 1471x6x4x4 .312 0.72 0.69 0.88 D1 3/8 1/4 1471x6 .312 0.80 0.80 0.93 MN 3/8 3/8 1471x6x6x6 .406 0.85 0.85 0.92 1/2 3/8 1471x8 .406 0.94 0.94 1.10
MTO - Made To Order

Brass Products

Air Brake – Nylon Tubing
Adapter Tee
insert
(Brass)
gauge ring
Nut screwed to Gauge Ring assures installation to specifications.
Note:
Use with NT100 Air Brake Tubing (SAE J844), see page 27.
TuBE FEM. PiPE MAlE PiPE CATAlOg

D1
O.D. ThrEAD ThrEAD NuMBEr D1 M N N1
3/8 1/4 1/4 1482x6x4x4 .312 0.88 0.75 0.94

N1 MTO - Made To Order
M N
TuBE CATAlOg

A
O.D. NuMBEr A B C D

B
1/4 1484x4 0.64 0.46 .163 .133

DC 3/8 1484x6 0.76 0.58 .245 .215 1/2 1484x8 0.94 0.76 .370 .340
5/8 1484x10 1.06 0.84 .434 .398
3/4 1484x12 1.21 1.00 .559 .523

L
TuBE CATAlOg
O.D. NuMBEr l
1/4 1485x4 .085/.105 3/8 1485x6 .125/.145 1/2 1485x8 .100/.120 5/8 1485x10 .115/.135
3/4 1485x12 .180/.200

Refer to safety information regarding

Brass Products Note:
proper selection of tubing on page 1.
For additional technical

Air-Brake questions, contact Technical Support at Copper Tubing 1-888-258-0222.
A

Tube O.D. 1/4 3/8 1/2 5/8 3/4 1
Thread Size-B 7/16–24 17/32–24 11/16–20 13/16–18 1–18 1-1/4-16
Typical Application:
Air brake systems.
Pressure:
Maximum operating pressure of 150 psi.
Vibration:
Fair resistance.
Temperature Range:
-65°F to +250°F (-53°C to +121°C) with copper tubing.
Material:
CA360 Brass.
Used With:
Copper tubing in air brake systems.
Advantages:
Easy to assemble (no flaring). May be used with nylon tubing by replacing long nut and spherical sleeve with insert, rigid sleeve and nut. See page 84 for details.
Conformance:
Meets specifications and standards of SAE and DOT.
How to Order:
For complete assemblies For complete assemblies (body, nuts and sleeves), order by catalog number. Example: 1368x4. To order body only (less nut and sleeve), add prefix “B” to catalog number. Example: B1368x4. Nuts and sleeve can be ordered separately by catalog number.
To order complete assembly with pipe sealant (Seal-A-Thread), add suffix “Z” to catalog number. Example: 1368x4Z (special order only).
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice. Additional information can be found in SAE J246.
Assembly Instructions:
1.
Cut tubing to desired length. Make sure all burrs are removed and the ends are cut square.

2.
Slide nut and then sleeve on tubing. Threaded end of nut “A” must face toward connector body.

3.
Insert tubing into connector. Be sure tubing is bottomed on fitting shoulder.

4.
Thread nut onto connector body until it is hand tight.

5.
From that point, tighten with a wrench the number of turns indicated in the chart below.

AddiTiONAl TuBE NuMBEr Of TurNs sizE frOM hANd TighT
1/4, 3/8 1-3/4
1/2, 5/8, 3/4 3-1/4
Label Set:
FS-800 (adhesive) CL-491 (non-adhesive)

Brass Products
Air-Brake Copper Tubing
EH TuBE E
O.d. TuBE dEPTh h
H is hand tight dimensions.
sleeve
L
(Ref. SAE No. 120115)
D
F
Nut
L
C
(Ref. SAE No. 120111)
D
union
L
C
(Ref. SAE No. 120101BA)
D
Male Connector
L
C
(Ref. SAE No. 120102BA)
D
D1
1/4
3/8
1/2
5/8
3/4
TuBE
O.d.
1/4
3/8
1/2
5/8
3/4
TuBE
O.d.
1/4
3/8
1/2
5/8
3/4
TuBE
O.d.
1/4
3/8
1/2
5/8
3/4
1
TuBE
O.d.
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/2
1/2
5/8
5/8
3/4
3/4 0.25 0.58
0.31 0.87
0.44 0.95
0.44 1.05
0.56 1.25
CATAlOg NuMBEr d f l
1360x4 .255 .322 .250
1360x6 .382 .461 .313
1360x8 .507 .594 .375
1360x10 .632 .734 .438
1360x12 .758 .874 .500
CATAlOg NuMBEr C d l
1361x4 9/16 .256 0.75
1361x6 5/8 .384 1.13
1361x8 13/16 .509 1.25
1361x10 15/16 .634 1.38
1361x12 1-1/8 .760 1.56
CATAlOg NuMBEr C d l
1362x4 7/16 .188 0.85
1362x6 9/16 .312 1.10
1362x8 11/16 .406 1.31
1362x10 13/16 .531 1.43
1362x12 1 .656 1.60
1362x16 1-1/4 .875 1.78
MAlE PiPE CATAlOg ThrEAd NuMBEr C d d1 l
1/8 1368x4 7/16 .188 .188 0.88
1/4 1368x4x4 9/16 .188 .188 1.09
1/8 1368x6x2 9/16 .312 .188 1.02
1/4 1368x6 9/16 .312 .312 1.20
3/8 1368x6x6 11/16 .312 .406 opt. 1.23
1/2 1368x6x8 7/8 .312 .531 opt. 1.42
1/4 1368x8x4 11/16 .406 .312 1.32
3/8 1368x8 11/16 .406 .406 1.32
1/2 1368x8x8 7/8 .406 .531 opt. 1.51
3/8 1368x10x6 13/16 .531 .406 1.38
1/2 1368x10 7/8 .531 .531 1.57
1/2 1368x12 1 .656 .531 1.67
3/4 1368x12x12 1-1/16 .656 .719 opt. 1.70

Brass Products
Air-Brake Copper Tubing
female Connector
(Ref. SAE No. 120103BA)
45° Male Elbow
(Ref. SAE No. 120302BA)
90° Male Elbow
(Ref. SAE No. 120202BA)
90° Male Elbow - long
L
C
D
D1
D
N
M
D1 N D M
D
N
M
TuBE
O.d.
3/8
3/8
1/2
TuBE
O.d.
3/8
3/8
1/2
5/8
TuBE
O.d.
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/2
1/2
5/8
5/8
TuBE
O.d.
3/8
1/2
fEM. PiPE ThrEAd
1/4
3/8
3/8
MAlE PiPE ThrEAd
1/4
3/8
3/8
1/2
MAlE PiPE ThrEAd
1/8
1/4
1/8
1/4
3/8
1/2
1/4
3/8
1/2
3/8
1/2
MAlE PiPE ThrEAd
1/4
3/8
CATAlOg
NuMBEr

1366x6
1366x6x6
1366x8
CATAlOg
NuMBEr

1380x6
1380x6x6
1380x8
1380x10
CATAlOg
NuMBEr

1369x4
1369x4x4
1369x6x2
1369x6
1369x6x6
1369x6x8
1369x8x4
1369x8
1369x8x8
1369x10x6
1369x10
CATAlOg
NuMBEr

1369x6L
1369x8L
C d l
11/16 .312 1.19
7/8 .312 1.19
7/8 .406 1.28
d d1 M N
.312 .312 0.72 0.86
.312 .406 0.76 0.95
.406 .406 0.85 0.95
.531 .531 0.94 1.17
d d1 M N
.188 .188 0.63 0.67
.188 .312 0.69 0.88
.312 .188 0.73 0.75
.312 .312 0.80 0.93
.312 .406 0.85 0.92
.312 .531 0.95 1.11
.406 .312 0.87 1.00
.406 .406 0.94 1.00
.406 .531 1.04 1.19
.531 .406 1.01 1.06
.531 .531 1.10 1.25
d MN
.312 0.81 1.44
.406 1.25 1.38

Brass Products
Air-Brake Copper Tubing
union Tee TuBE CATAlOg
O.d. NuMBEr M M1 d d1
(Ref. SAE No. 120401BA) 3/8 1364x6 0.80 0.80 .312 .312 D1 M1 1/2 1364x8 0.94 0.94 .406 .406 DD MM
Male run Tee TuBE MAlE PiPE CATAlOg
O.d. ThrEAd NuMBEr d M M1 N
(Ref. SAE No. 120424BA) 3/8 1/4 1371x6 .312 0.80 0.80 0.93 M1 3/8 3/8 1371x6x6x6 .406 0.85 0.85 0.92 D MN
TuBE TuBE MAlE Male Branch Tee D O.d. O.d. PiPE CATAlOg A B ThrEAd NuMBEr d M N
(Ref. SAE No. 120425BA) N
3/8 3/8 1/4 1372x6 .312 0.80 0.93 3/8 3/8 3/8 1372x6x6x6 .406 0.85 0.92
MM
1/2 1/2 3/8 1372x8 .406 0.94 1.00
fEM. PiPE CATAlOg ThrEAd Bulkhead Coupling L ThrEAd ThrEAd sizE B C C1 d i l
(Brass) DI 1/4 1344 3/4–16 1 15/16 .422 1.25 1.50 Pipe Pipe 1/4 1345 3/4–16 1 15/16 .422 0.69 0.94 Thread Thread 3/8 1346 1–14 1-1/8 1-3/8 .563 1.06 1.31 1/2 1351 1-1/8–14 1-1/4 1-3/8 .703 1.19 1.50
Thread Size-B C1 C

Brass Products

Air-Brake Copper Tubing

MAlE fEM.
Bulkhead Coupling
L

PiPE PiPE CATAlOg ThrEAd
ThrEAd ThrEAd NuMBEr sizE B C C1 d i l
I
(Brass)

Pipe1/2 1/4 1340 3/4–16 1-1/4 15/16 .312 1.13 2.16
Thread
D

1/2 1/4 1341 3/4–16 1-1/4 15/16 .312 1.53 2.53
Thread
Pipe
Size-B
Thread C C1

MAlE fEM.
Bulkhead Coupling
L

PiPE PiPE CATAlOg ThrEAd d i l ThrEAd ThrEAd NuMBEr sizE B C C1
(Brass) I Thread Size-B

1/2 1/4 1342 1–14 1-1/4 1-3/8 .375 1.88 2.94
1/2 1/4 1343 1–14 1-1/4 1-3/8 .375 2.88 3.94
D
Pipe
Pipe

C1 Thread
Thread C

MAlE PiPE CATAlOg
draincock
L

ThrEAd NuMBEr d l
1/4 W15310 .188 1.56
D

MAlE fEM.
shut Off Valve
L

PiPE PiPE CATAlOg d ThrEAd ThrEAd NuMBEr C C1
1/4 1/4 W20332 5/8 3/4 .218 1.81
D
C1 C
Rating: 125 psi with one 1/4" bubble in 5 seconds permissible key leakage.

MAlE PiPE CATAlOg
External seat draincock

ThrEAd NuMBEr C
1/4 145 9/16 1.00
L
C

Brass Products Note:
For additional technical

Threaded Sleeve questions, contact Technical Support at 1-888-258-0222.

Tube O.D. 1/8 3/16 1/4 5/16 3/8
Thread Size-B 5/16–24 3/8–24 7/16–24 1/2–20 9/16–20
Typical Application:
Oil, air, water and lubrication systems.
Pressure:
Operating pressure of 500 psi for 1/8” to 1/4” sizes, 250 psi for 5/16” and 3/8” sizes.
Vibration:
Fair resistance.
Temperature Range:
-65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
Material:
CA360 Brass.
Used With:
Aluminum and copper tubing. Not recommended for steel tubing.
Advantages:

Easy to assemble, no flaring. Two (2) piece construction.
Conformance:
Meets ASA and ASME specifications.
How to Order:
Order individually by catalog number.
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice.
Assembly Instructions:
1.
Cut tubing to desired length.

2.
Slide nut on end of tube. Threaded end “A” of nut must face toward connector.

Note:
The lead end of nut incorporates the sleeve as a single piece.
3.
Insert tube into connector body. Be sure tube is bottomed on connector shoulder.

4.
Lubricate threads and assemble nut to connector body.

5.
From that point, tighten Tighten nut, hand tight. From hand tight, tighten with a wrench 1-1/2 additional turns to form proper seal.

Brass Products
Threaded Sleeve

TuBE CATAlOg
Nut
O.d. NuMBEr

d l

1/8 6100x2 3/8 .130 0.50 3/16 6100x3 7/16 .193 0.53 1/4 6100x4 1/2 .255 0.56 5/16 6100x5

9/16 .318 0.61 3/8 6100x6

5/8 .380 0.61

MTO - Made To Order

TuBE MAlE PiPE CATAlOg
Male Connector
O.d. ThrEAd NuMBEr

d l

1/8 1/8 6200x2 7/16 .078 0.62 1/8 * 6200x2x21 7/16 .080 0.62 3/16 1/8 6200x3 7/16 .141 0.69 1/4 1/8 6200x4 1/2 .188 0.75 5/16 1/8 6200x5

9/16 .219 0.89 3/8 1/4 6200x6

5/8 .312 0.97
*Thread Size 1/4-28 Tapered Male Thread.

MTO - Made To Order

TuBE MAlE PiPE CATAlOg
Male Elbow
O.d. ThrEAd NuMBEr d d1 M N

1/8 1/8 6400x2 .073 .125 0.50 0.66 1/8 * 6400x2x21 .078 .080 0.50 0.52 3/16 1/8 6400x3 .141 .156 0.56 0.62 1/4 1/8 6400x4 .188 .188 0.52 0.62
*Thread Size 1/4-28 Tapered Male Thread.

Brass Products Note:
For additional technical
Pipe questions, contact Technical Support at 1-888-258-0222.

Pipe Thread Size B

Pipe Size 1/16 1/8 1/4 3/8 1/2 3/4
Thread Size-B 1/16–27 1/8–27 1/4–18 3/8–18 1/2–14 3/4–14
Typical Application:
Grease, refrigeration, instrumentation and hydraulic systems. Fuel, LP and natural gas available on special order.
Pressure:
Operating pressure up to 1200 psi.
Vibration:
Fair resistance.
Temperature Range:
-65°F to +250°F (-53°C to +121°C).
Material:
CA360 Brass.
Used With:
Brass, bronze and iron pipe.
Advantages:
Dryseal pipe threads (NPTF). Large range of sizes and configurations.
Conformance:
Listed by Underwriters Laboratories (available on special order) for fuel equipment, refrigeration and gas. Meets specifications and standards of ASA, ASME and SAE.
How to Order:
Order individually by catalog number. Example: 3325x4. To order with pipe sealant (Seal-A-Thread), add a “Z” suffix to the catalog number. (Special order only). Example: 3325x4Z.
Note:
Refer to current price list for availability of cataloged items. Quotations and delivery of non-stock items supplied on request. Configurations and dimensions subject to change without notice. Additional information can be found in SAE J530 Automotive Pipe Fittings and SAE J531 Drain Plugs.

Assembly Instructions:
1.
Tighten approximately 2-1/2 turns past hand tight.

2.
Connectors with Seal-A-Thread tighten two turns past hand tight. Brittle materials require special cautions.

Label Set:
W-8022 (adhesive) CL-490 (non-adhesive)

Brass Products
Pipe
fEM.

Cap
L
PiPE CATAlOg ThrEAd NuMBEr C l

C
1/8* 3129x2 9/16 .50 1/4* 3129x4 11/16 .59 3/8* 3129x6 13/16 .68
*PTF Short Thread
MAlE

slotted Plug
PiPE CATAlOg

L
E ThrEAd NuMBEr E l
1/8* 3150x2 .05 .28 1/4* 3150x4 .08 .42
3/8* 3150x6 .09 .43
*PTF Short Thread
MAlE

square head Plug
L
PiPE CATAlOg squArE ThrEAd NuMBEr C f l

F
1/8* 3151x2 .28 .24 .58

C 1/4* 3151x4 .37 .29 .74 3/8* 3151x6 .43 .32 .82 1/2* 3151x8 .56 .39 .99 3/4* 3151x12 .62 .43 1.12
*PTF Short Thread
MAlE

hex head Plug
L
PiPE CATAlOg ThrEAd NuMBEr C f l

C
1/8* 3152x2 7/16 .19 .57 1/4* 3152x4 9/16 .18 .62 3/8* 3152x6 11/16 .22 .72 1/2* 3152x8 7/8 .22 .78 3/4** 3152x12 1-1/16 .25 .88

F
*PTF Short Thread **PTF Special Short Thread
MAlE

hex socket Plug
PiPE CATAlOg sOCkET ThrEAd NuMBEr hEx l

L Socket
Hex 1/8 3153x2 3/16 .270 1/4 3153x4 1/4 .410 3/8 3153x6 5/16 .410 1/2 3153x8 3/8 .540
MTO - Made To Order
fEM. MAlE

Adapter
L
PiPE PiPE CATAlOg ThrEAd ThrEAd NuMBEr C d l

C
(Ref. SAE No. 130139)
1/8 1/8 3200x2 9/16 .219 .88
1/4 1/8 3200x4x2 3/4 .219 1.06 1/4 1/4 3200x4 3/4 .312 1.25 3/8 1/4 3200x6x4 7/8 .312 1.25 3/8 3/8 3200x6 7/8 .438 1.25 1/2 3/8 3200x8x6 1-1/16 .438 1.47 3/4 3/8 3200x12x6 1-1/4 .438 1.59 3/4 1/2 3200x12x8 1-1/4 .562 1.69

D

Brass Products

Pipe

MAlE fEM.
Bushing

PiPE PiPE CATAlOg ThrEAd ThrEAd NuMBEr

d l
(Ref. SAE No. 130140)

1/4* 1/8 3220x4x2 5/8 .339 0.59 3/8 1/8 3220x6x2 11/16 .328 0.75 3/8* 1/4 3220x6x4 11/16 .438 0.69 1/2* 1/8 3220x8x2 7/8 .530** 0.75 1/2* 1/4 3220x8x4 7/8 .438** 0.75 1/2* 3/8 3220x8x6 7/8 .562 0.75 3/4* 3/8 3220x12x6 1-1/8 .562 0.88 3/4* 1/2 3220x12x8 1-1/8 .703 0.88
*PTF Short Thread **Optional Counterbore
fEM.
union

PiPE CATAlOg ThrEAd NuMBEr

d l

1/4* 3250x4 1-1/16 .438 1.31

D 1/2 3250x8 1-9/16 .703 1.81
*PTF Short Thread

fEM.
Coupling

PiPE CATAlOg ThrEAd NuMBEr

d l
(Ref. SAE No. 130138)

1/16 3300x1 7/16 .339 0.75 1/8 3300x2 9/16 .339 0.75 1/4 3300x4 3/4 .438 1.12 3/8 3300x6 7/8 .578 1.12 1/2 3300x8 1-1/16 .703 1.50 3/4 3300x12 1-1/4 .906 1.53

fEM. fEM.
reducer Coupling

PiPE PiPE ThrEAd ThrEAd CATAlOg
A A1 NuMBEr

d l
(Ref. SAE No. 130138) 1/4 1/8 3300x4x2 3/4 .339 0.96 D 3/8 1/8 3300x6x2 7/8 .339 0.94 3/8 1/4 3300x6x4 7/8 .438 1.16
A A1 1/2 3/8 3300x8x6 1-1/16 .562 1.38

restriction Pipe Adapter MAlE fEMAlE
PiPE PiPE CATAlOg ThrEAd ThrEAd NuMBEr

d l
(With .0625 Orifice)

1/8 1/8* 1512 1/2 .0625 0.75
*PTF Short Thread

NOTE: Other orifice sizes available (special order only).

Brass Products
Pipe
hex Nipple
(Ref. SAE No. 130137)
L
C
D1
D
A A1
Close Nipple L
D
long Nipple
L
D
MAlE MAlE PiPE PiPE ThrEAd ThrEAd CATAlOg A A1 NuMBEr C d d1 l
1/16 1/16 3325x1 3/8 .125 .125 .978
1/8 1/16 3325x2x1 7/16 .230 .156 .955
1/8 1/8 3325x2 7/16 .219 .219 0.97
1/4 1/8 3325x4x2 9/16 .219 .219* 1.19
1/4 1/4 3325x4 9/16 .312 .312 1.38
3/8 1/8 3325x6x2 11/16 .219 .438 1.22
3/8 1/4 3325x6x4 11/16 .312 .438 1.41
3/8 3/8 3325x6 11/16 .438 .438 1.41
1/2 1/2 3325x8 7/8 .562 .562 1.81
3/4 3/4 3325x12 1-1/16 .750 .750 1.94
*Optional .312 Counterbore on 1/4" side.
MAlE PiPE CATAlOg ThrEAd NuMBEr d l
1/8 3326x2 .281 0.75
1/4 3326x4 .375 0.88
3/8 3326x6 .500 1.00
1/2 3326x8 .625 1.12
3/4 3326x12 .750 1.38
MAlE PiPE CATAlOg ThrEAd NuMBEr d l
1/8 3327x2 .281 1.50
1/8 3328x2 .281 2.00
1/8 3329x2 .281 2.50
1/8 3330x2 .281 3.00
1/8 3331x2 .281 3.50
1/4 3327x4 .375 1.50
1/4 3328x4 .375 2.00
1/4 3329x4 .375 2.50
1/4 3330x4 .375 3.00
1/4 3331x4 .375 3.50
3/8 3327x6 .480 1.50
3/8 3328x6 .490 2.00
3/8 3329x6 .480 2.50
3/8 3330x6 .480 3.00
3/8 3331x6 .480 3.50
1/2 3328x8 .625 2.00
1/2 3329x8 .625 2.50
1/2 3330x8 .625 3.00
3/4 3328x12 .750 2.00
3/4 3329x12 .750 2.50
MTO - Made To Order

Brass Products
Pipe
fEM. PiPE CATAlOg ThrEAd
Bulkhead Coupling
L
ThrEAd NuMBEr sizE B C C1 d i l
(Brass)
I
1/4 1344 3/4–16 1 15/16 .422 1.25 1.50
D Pipe 1/4 1345 3/4–16 1 15/16 .422 0.69 0.94
Pipe
Thread

Thread 3/8 1346 1–14 1-1/8 1-3/8 .563 1.06 1.31 1/2 1351 1-1/8–14 1-1/4 1-3/8 .703 1.19 1.50
Thread
Size-B C1 C
MAlE fEM.
Bulkhead Coupling
L
PiPE PiPE CATAlOg ThrEAd d i l
Thd. Thd. NuMBEr sizE B C C1
I
(Brass)
Pipe
Thread 1/2 1/4 1340 3/4–16 1-1/4 15/16 .312 1.13 2.16 D
1/2 1/4 1341 3/4–16 1-1/4 15/16 .312 1.53 2.53
Thread
Pipe
Size-B
Thread C C1

MAlE fEM.
Bulkhead Coupling
L
PiPE PiPE CATAlOg ThrEAd
Thd. Thd. NuMBEr sizE B C C1 d i l
I
(Brass)
Thread
1/2 1/4 1342 1–14 1-1/4 1-3/8 .375 1.88 2.94
Size-B
1/2 1/4 1343 1–14 1-1/4 1-3/8 .375 2.88 3.94
D
Pipe
Pipe
Thread C C1 Thread

MAlE fEM.
45° street Elbow
PiPE PiPE CATAlOg C ThrEAd ThrEAd NuMBEr C d N N1
(Ref. SAE No. 130339)
1/8 1/8 3350x2 9/16 .219 0.50 0.38
D
N1 1/4 1/4 3350x4 11/16 .312 0.74 0.56 3/8 3/8 3350x6 13/16 .438 0.78 0.56 1/2 1/2 3350x8 1 .562 1.00 0.76 3/4 3/4 3350x12 1-1/4 .750 1.06 0.75
N
fEM. MAlE
90° street Elbow
N
PiPE PiPE CATAlOg
ThrEAd ThrEAd NuMBEr C d E N N1
C
(Ref. SAE No. 130239)
1/8 1/8 3400x2 9/16 .219 0.25 0.66 0.47
N1
1/8* 1/8** 3400x2W 1/2 .188 0.25 0.57 0.34
DE 1/4 1/8 3400x4x2 11/16 .219 – 0.72 0.53 1/4* 1/4** 3400x4W 11/16 .266 0.36 0.78 0.45 1/4 1/4 3400x4 11/16 .312 – 0.91 0.72 3/8 3/8 3400x6 13/16 .438 – 0.97 0.78 1/2 1/2 3400x8 1 .562 – 1.25 1.03 3/4 3/4 3400x12 1-1/4 .750 – 1.38 1.12
*PTF short thread.
**PTF special short thread.

Brass Products

Pipe
90° Elbow
(Ref. SAE No. 130238)

Male Branch Tee
(Ref. SAE No. 130425)

Tee
(Ref. SAE No. 130438)

Male run Tee
(Ref. SAE No. 130424)

Cross

fEM. PiPE ThrEAd CATAlOg NuMBEr C d N
1/8 3500x2 9/16 .339 0.55
1/4 3500x4 11/16 .438 0.78
3/8 3500x6 13/16 .562 0.84
1/2 3500x8 1 .703 1.09
3/4 3500x12 1-1/4 .906 1.16

fEM. MAlE PiPE PiPE ThrEAd ThrEAd CATAlOg NuMBEr C d l l2 N
1/8 1/8 3600x2 9/16 .219 1.10 0.55 0.66
1/4 1/4 3600x4 11/16 .312 1.56 0.78 0.91
3/8 3/8 3600x6 13/16 .438 1.68 0.84 0.97
1/2 1/2 3600x8 1 .562 2.18 1.09 1.25
3/4 3/4 3600x12 1-1/4 .750 2.31 1.16 1.38

fEM. PiPE ThrEAd CATAlOg NuMBEr C d l l2
1/8 3700x2 9/16 .339 1.10 0.55
1/4 3700x4 11/16 .438 1.56 0.78
3/8 3700x6 13/16 .562 1.68 0.84
1/2 3700x8 1 .703 2.18 1.09
3/4 3700x12 1-1/4 .906 2.32 1.16

fEM. MAlE PiPE PiPE ThrEAd ThrEAd CATAlOg NuMBEr C d M N
1/8 1/8 3750x2 9/16 .219 0.55 0.66
1/4 1/4 3750x4 11/16 .312 0.78 0.90
3/8 3/8 3750x6 13/16 .438 0.84 0.97
1/2 1/2 3750x8 1 .562 1.09 1.25
3/4 3/4 3750x12 1-1/4 .750 1.16 1.38

fEM. PiPE ThrEAd CATAlOg NuMBEr C d M
1/8 3950x2 1/2 .339 0.50
1/4 3950x4 11/16 .438 0.75
3/8 3950x6 7/8 .562 0.81
1/2 3950x8 1 .703 1.09

Refer to safety information regarding

Brass Products Note:
proper selection of tubing on page 1.
For additional technical

Needle Valves questions, contact Technical Support at 1-888-258-0222.

Typical Application:
Instrumentation, hydraulic and pneumatic systems.
Pressure:
150 psi maximum. (Does not include plastic tubing.)
Temperature Range:
-65°F to +250°F (-53°C to +121°C) with metal tubing. For valves using compatible tubing, refer to the tubing temperature range.
Material:
Brass bodies, steel handles except where noted. Polyline valves have brass bodies and brass handles.
Used With:
Copper, aluminum, steel and plastic tubing where applicable.
Advantages:

Metal-to-metal seat, with fine thread screw down, enables valves to seat positively, adjust easily and hold to any amount of flow up to capacity of the valve.
Conformance:

Designed for automotive and industrial use. Not intended for natural gas, LPG, nuclear or aircraft applications.
How to Order:
Order valve body, nuts and sleeves by catalog number. Order valve with Selfalign nuts and sleeves by adding suffix “S”. Example: A6763 becomes A6763S. Order valves less nuts and sleeves by adding prefix “B”. Example: A6763 becomes B6763.
Assembly Instructions:
Install with the pressure against the seat. Inspection of a straight valve discloses one opening to be higher than the other. Pressure should always be directed against the seat in angle valves, not the stem threads.

Brass Products
Needle Valves
Compression double
MM1
Flow L
Compression straightway
M M1
Flow L
Compression Angle
M M1 L Flow N
inverted straightway
MM1 Flow
NL
TuBE CATAlOg
O.d. NuMBEr l M M1
3/16 A6763 1.06 0.88 1.03 1/4 A6765 1.13 0.88 1.03 1/4 A6765S 1.13 0.88 1.03 5/16 A6770 1.13 0.88 1.03 3/8 A6775 1.50 1.13 1.31
“S” suffix designates Selfalignwith nuts and sleeves.
TuBE MAlE PiPE CATAlOg
O.d. ThrEAd NuMBEr l M M1
3/16 1/8 A6690 1.16 0.88 1.03 3/16 1/8 A6690S 1.16 0.88 1.03 1/4 1/8 A690 1.19 0.88 1.03 1/4 1/8 A690S 1.19 0.88 1.03 5/16 1/8 A660 1.18 0.90 1.05 5/16 1/4 A6755 1.28 0.91 1.09 5/16 1/4 A6755S 1.28 0.91 1.09 3/8 1/4 A6760 1.82 1.31 1.46 3/8 1/4 A6760S 1.82 1.31 1.46
“S” suffix designates Selfalignwith nuts and sleeves.
TuBE MAlE PiPE CATAlOg
O.d. ThrEAd NuMBEr l M M1 N
3/16 1/8 A6845 1.50 0.82 1.07 0.50 1/4 1/8 A555 1.53 0.83 1.05 0.53 1/4 1/8 A555S 1.53 0.83 1.05 0.53 5/16 1/8 A655 1.56 0.84 1.09 0.52 5/16 1/4 A6855 1.73 0.92 1.28 0.69 5/16 1/4 A6855S 1.73 0.92 1.28 0.69 3/8 1/4 A6860 1.64 0.83 1.28 0.78 3/8 1/4 A6860S 1.64 0.83 1.28 0.78
“S” suffix designates Selfalignwith nuts and sleeves.
TuBE MAlE PiPE CATAlOg
O.d. ThrEAd NuMBEr l M M1 N
1/4 1/8 A735 1.38 0.84 1.01 0.69 1/4 1/8 B735 1.38 0.84 1.01 0.69
“B” prefix designates less inverted nut.
For replacement nut use 105x4. See page 32.

Brass Products
Needle Valves
Male Pipe double
MM1 Flow
L
Male to female Pipe MM1 Flow
L
female Pipe
MM1
G
Flow
L
sAE 45° flare double
M M1
Flow
L
MAlE PiPE CATAlOg ThrEAd NuMBEr l M M1
1/8 6810 1.38 0.66 0.80
1/4 6815 1.62 1.08 1.23
fEM. MAlE PiPE PiPE CATAlOg ThrEAd ThrEAd NuMBEr l M M1
1/8 1/8 6820 1.18 0.88 1.03
1/4 1/4 6825 1.88 1.09 1.24
fEM. PiPE CATAlOg ThrEAd NuMBEr l M M1 g
1/8 6800 1.12 0.88 1.03 0.50
1/4 6805 1.62 1.11 1.26 0.69
TuBE CATAlOg
O.d. NuMBEr l M M1
1/4 6715 1.38 0.87 1.03

Brass Products
Needle Valves
sAE 45° flare MAlE
TuBE PiPE CATAlOg straightway O.d. ThrEAd NuMBEr l M M1
MM1 1/4 1/8 530 1.31 0.88 1.03 Flow 1/4 1/4 6700 1.38 0.88 1.09 5/16 1/8 630 1.38 0.95 1.13 L 5/16 1/4 695 1.44 0.87 1.02 3/8 1/4 700 1.68 1.00 1.15
MAlE sAE 45° flare AngleTuBE PiPE CATAlOg
O.d. ThrEAd NuMBEr l M M1 N
MM1 1/4 1/8 320 1.54 0.86 1.07 0.68
L 5/16 1/8 325 1.59 0.94 1.22 0.88 Flow
5/16 1/4 6703 1.94 1.00 1.31 0.90 3/8 1/4 330 1.84 0.90 1.21 0.97
N
Polyline straightway MAlE
TuBE PiPE CATAlOg
O.d. ThrEAd NuMBEr l M M1
MM1 1/4 1/8 A690P 1.19 0.86 1.01 3/8 1/4 A6760P 1.50 1.18 1.33
L
Temperature Range: -40°F to +150°F with plastic sleeve.
For replacement Polyline nuts and sleeves, see page 54.
MAlE Polyline Angle TuBE PiPE CATAlOg
O.d. ThrEAd NuMBEr l M M1 N
MM1 1/4 1/8 A555P 1.50 0.82 1.04 0.48 1/4 1/4 A556P 1.70 0.84 1.06 0.56
L
3/8 1/4 A6860P 1.85 0.99 1.44 0.64
N
Temperature Range: -40°F to +150°F with plastic sleeve.
For replacement Polyline nuts and sleeves, see page 54.

Brass Products
Drain Cocks
External seat
External seat
internal seat
internal seat
(Long) Drain Cocks and Drain Valves have been a specialty since 1919. Millions are in use. The original design has proved so efficient that it is still the leader with most original equipment manufacturers. The metal-to-metal seat requires only hand tightening to assure positive leak-proof performance.
L
C
L
C
L1
LL1
C C
L
Note:
For additional technical questions, contact Technical Support at 1-888-258-0222.
Typical Application:
Brass bodies/steel handles, except where noted.
Pressure:
150 psi maximum (does not include hose or plastic tubing.)
Used With:
Copper, aluminum, steel, hose and plastic tubing where applicable.
MAlE
PiPE CATAlOg
ThrEAd NuMBEr

1/8 135
1/4 145
3/8 270
1/2 108
MAlE PiPE CATAlOg ThrEAd NuMBEr
1/4 6788
MAlE PiPE CATAlOg ThrEAd NuMBEr
1/8 130
1/4 140
1/4 190
3/8 230
MAlE PiPE CATAlOg ThrEAd NuMBEr
1/8 185
Refer to safety information regarding proper selection of tubing on page 1.
Temperature:
-65°F to +250°F (-53°C to +121°C). (Refer to tubing temperature range.)
Conformance:
Designed for automotive or industrial use. Not intended for natural gas, LPG, nuclear or aircraft applications, except as noted.
C l
7/16 0.90
9/16 1.00
11/16 1.25
7/8 1.52
C l l1
9/16 1.56 0.44
C l l1
17/32 1.15 1.30
5/8 1.32 1.50
9/16 1.25 1.41
11/16 1.34 1.50
C l
7/16 1.72

Brass Products
Drain Cocks
MAlE PiPE CATAlOg ThrEAd NuMBEr C l M
internal seat
M 1/8 6783 13/32 1.63 .344
C
L
MAlE
internal seat drain Valve
PiPE CATAlOg ThrEAd NuMBEr C l
1/8 1424A 1/2 1.219
C
L
1/4 1425A 9/16 1.313 3/8 1426A 11/16 1.688
MAlE
Air Vent
PiPE CATAlOg ThrEAd NuMBEr C l l1
1/8 705 13/32 0.78 0.88
C
LL1 Set screw has 10-32 national fine thread.
MAlE
Angle Bib drain M1
PiPE CATAlOg squArE ThrEAd NuMBEr C l M M1 N
M
1/8 150 7/16 1.12 0.57 0.95 0.38
C
1/4 120 5/8 1.76 0.94 1.50 0.66
Flow
N
L
MAlE
Angle Bib drain M1
hOsE PiPE CATAlOg squArE
i.d. ThrEAd NuMBEr C l M M1 N
M
3/8 1/4 6660 9/16 1.33 0.62 1.01 0.66
C
Flow
N
L

Brass Products
Drain Cocks
hose to Pipe
(Steel Body)
hose to Pipe
(Steel Body)
Pipe to hose shut-Off
(Brass Body)
Red color coded aluminum handle. Handle Catalog Number 1427.
gasoline shut-Off with screen filter
Air Tank drain Valve
Pull cable sideways.
MAlE
M1
hOsE PiPE CATAlOg sizE ThrEAd NuMBEr C l M M1N
M
5/8 3/8 211273A 11/16 2.85 1.41 1.91 1.30
C
Flow N L
M1 M
L
C Flow
N
M1 M L C
N
hOsE
i.d.
5/8
hOsE sizE
3/8
5/8
3/4
3/4
MAlE PiPE ThrEAd
3/8
MAlE PiPE ThrEAd
3/8
3/8
3/8
1/2
CATAlOg
NuMBEr

211280A
CATAlOg
NuMBEr

1422
1423
1433
1451
squArE C l M M1N
11/16 2.85 1.10 1.47 1.19
squArE C l MM1N
3/4 2.93 1.78 2.25 1.12
13/16 2.93 1.81 2.25 1.35
15/16 3.00 1.81 2.25 1.35
15/16 3.12 1.93 2.25 1.35
MAlE
L
hOsE PiPE CATAlOg sizE ThrEAd NuMBEr l M M1 N
1/4 1/8 6600 3.36 0.80 0.97 0.84
N
M
M1

MAlE PiPE CABlE CATAlOg ThrEAd lENgTh NuMBEr
1/4 7" 1421-7
1/4 18" 1421-18
1/4 24" 1421-24
1/4 32" 1421-32
1/4 60" 1421-60
1/4 60" 1421-60A*
*No loop on cable end.

Brass Products
Truck Valves
Typical Application:
Used extensively in the trucking industry for cooling and fuel line applications.
Material:
Forged brass bodies, steel handles.
Pressure Range:
200 psi maximum.

Truck Valve

Truck Valve

Truck Valve

Truck Valve

Temperature: Note:
-40°F to +250°F Buna-N o-ring sealed;
(-40°C to +121°C)
Conformance:
Designed for trucking use.
Not intended for natural
gas, LPG, nuclear or aircraft
applications.
HOsE i.D. PiPE THrEAD CATAlOg NuMBEr
5/8 1/2 7502

HOsE PiPE CATAlOg
i.D. THrEAD NuMBEr
5/8 3/8 7504
HOsE PiPE CATAlOg
i.D. THrEAD NuMBEr
3/8 3/8 7506
FEMAlE MAlE
PiPE THrEAD PiPE THrEAD CATAlOg NuMBEr
1/2 1/2 7508

FEMAlE MAlE
Truck Valve
PiPE PiPE CATAlOg THrEAD THrEAD NuMBEr
3/8 3/8 7509

Brass Products
Plastic Drain Cocks
Material: Temperature:
Nylon 6 Fiber Reinforced. -50°F to +180°F
Pressure Range: (-46°C to +82°C)

Up to 25 psi. Conformance:
Used With Designed for automotive

Automotive Radiators: use. Not intended for

natural gas, LPG, nuclear or aircraft applications.
Chrysler
M12x1.25
THrEAD CATAlOg NuMBEr THrEAD CATAlOg NuMBEr
Captive 110 M12x1.25 114

M10x1.25

Ford

THrEAD CATAlOg NuMBEr THrEAD CATAlOg NuMBEr
M10x1.25 118 M14x2.0 124
M12x1.5
Chrysler
THrEAD CATAlOg NuMBEr THrEAD CATAlOg NuMBEr
M12x1.5 119 5/8–18 125

gM THrEAD Oversized CATAlOg NuMBEr 111 M14x1.25 THrEAD M14x1.25 CATAlOg NuMBEr 115 Ford and Mazda THrEAD M10x1.25 CATAlOg NuMBEr 121 Chrysler THrEAD 5/8–18 CATAlOg NuMBEr 126
Ford (long) THrEAD CATAlOg NuMBEr Captive 112 M10x1.25 THrEAD M10x1.25 CATAlOg NuMBEr 116 M14x2.0 THrEAD M14x2.0 CATAlOg NuMBEr 122 gM THrEAD Captive CATAlOg NuMBEr 127
Ford (short) M14x1.25
Chrysler
gM

THrEAD CATAlOg NuMBEr THrEAD CATAlOg NuMBEr THrEAD CATAlOg NuMBEr THrEAD CATAlOg NuMBEr
Captive 113 M14x1.25 117 5/8–18 123 1/2–18 128

Brass Products

Ground Plug & Multiple Shut-Offs
Pressure Range:
30 psi working pressure, except where noted.
Used With:
Copper, aluminum, steel and plastic tubing where applicable.
Material:
Brass bodies and handles.
Temperature:
-65°F to +250°F (-53°C to +121°C) with metal tubing. For use with plastic tubing, refer to the tubing temperature range.
Draincock
L
D

Ratings:
Valves are designed to hold air pressure of 125 psi with one 1/4" bubble in 5 seconds permissible key leakage.
ground Plug Drain
C
N
M1
sAE 45° Flare Double
M
L
Note:
For additional technical questions, contact Technical Support at 1-888-258-0222.
Conformance:
Designed for automotive or industrial use. Not intended for natural gas, LPG, nuclear or aircraft applications, except as noted.
Ordering Information:
Order valve body, nut and sleeves by catalog number. Order valves with Selfalign nuts and sleeves by adding suffix “S”. Example: A694S. Order valves less nut and sleeve by adding prefix “B”. Example: B694.
MAlE PiPE CATAlOg THrEAD NuMBEr

Refer to safety information regarding proper selection of tubing on page 1.
Note:
Ground Plug Drains and Shut-Offs use a universal lubricant satisfactory for use with most common fluids. However the lubricant may wash out at higher pressures or with some exotic fluids.
Dl

1/4 W15310 .188 1.56
MAlE PiPE CATAlOg THD. NuMBEr C l N MM1
1/8 6891 9/16 1.93 0.75 1.63 0.87
1/4 6892 5/8 1.62 0.75 1.75 1.03
3/8 6893 11/16 1.72 1.00 2.31 1.22
TuBE CATAlOg

O.D. NuMBEr l M
1/4 6719 1.88 1.88
5/16 6724 1.88 1.88
3/8 6729 2.00 1.88

Brass Products

Ground Plug & Multiple Shut-Offs

MAlE
sAE 45° Flare
TuBE PiPE CATAlOg
O.D. THrEAD NuMBEr l M
straightway

1/4 1/8 537 2.00 1.88 5/16 1/8 632 2.03 1.88 3/8 1/4 703 2.06 1.88

TuBE CATAlOg
Compression Double
O.D. NuMBEr l M

1/4 A6769 2.12 1.88 1/4 A6769S 2.12 1.88 5/16 A6774 2.19 1.88 3/8 A6779 2.25 1.88 3/8 A6779S 2.25 1.88
“S” suffix designates Selfalign with Nuts and Sleeves.

MAlE
Compression
TuBE PiPE CATAlOg
O.D. THrEAD NuMBEr l M
straightway

M 1/4 1/8 A694 2.19 1.88 1/4 1/8 A694S 2.19 1.88 1/4 1/4 A6754 2.19 1.88 1/4 1/4 A6754S 2.19 1.88 5/16 1/8 A664 2.19 1.88 5/16 1/4 A6759 2.25 1.88 3/8 1/4 A6764 2.38 1.88 3/8 1/4 A6764S 2.38 1.88

“S” suffix designates Selfalign with Nuts and Sleeves.

MAlE FEMAlE
Male to Female Pipe
PiPE PiPE CATAlOg THrEAD THrEAD NuMBEr l M

1/8 1/8 6824 2.00 1.88 1/4 1/4 6829 2.12 1.88

MAlE FEMAlE
Truck shut Off
PiPE PiPE CATAlOg THrEAD THrEAD NuMBEr

l D
Male to Female Pipe
1/4 1/4 W20332 5/8 3/4 1.81 .218

D

Ratings:
Valves are designed to hold air pressure of 125 psi with one 1/4" bubble in 5 seconds permissible key leakage.

Brass Products

Ground Plug & Multiple Shut-Offs

MAlE FEMAlE
Marine shut Off Male

PiPE PiPE CATAlOg THD. THD. NuMBEr l M
to Female Pipe

1/4 1/4 6828 2.22 1.97

UL Listed for Marine Fuel.

FEMAlE
Female Pipe Double

PiPE CATAlOg THrEAD NuMBEr l M

1/8 6804 1.46 1.88 1/4 6809 1.70 1.88

FEMAlE
3 Way Multiple

PiPE l CATAlOg THrEAD sTEM NuMBEr
shut-Off

1/4 1.37 6749 3/8 1.37 6709

Replacement Handle:
Catalog Number 6746. Includes Screw. Click-washer assembly positively holds valve in desired position and gives a pronounced click.
4 Way Multiple shut-Off

Replacement Handle:
Catalog Number 6746. Includes Screw. Click-washer assembly positively holds valve in desired position and gives a pronounced click.

FEMAlE PiPE THrEAD l sTEM CATAlOg NuMBEr
1/4 1.37 6747
1/4 2.37 6748
3/8 1.37 6707
3/8 2.37 6708

Brass Products
Brass Ball Valves
Forged Body Brass 3-Way Ball Valve

Forged Body Brass Ball Valve

Features/Benefits
.
Forged brass body

.
Blowout proof stem

.
Chrome plated ball

.
Double o-ring stem seal

-never needs tightening

.
Floating ball design

.
Standard steel handle

PArT NuMBEr CONNECTiONs siZE X Y Z
FF90587-04 FF90587-06 FF90587-08 F x F x F NPT F x F x F NPT F x F x F NPT 1/4” 3/8” 1/2” 3.20 3.20 3.20 3.12 3.12 3.12 2.25 2.25 2.25

Applications
.
Vacuum service

.
Industrial service

.
Machine/engine coolant

.
Center off position

.
Diverter valve

PArT
NuMBEr CONNECTiONs siZE X Y Z D
FF90588-04 M x F NPT 1/4” 3.70 2.38 2.75 1.13
FF90588-06 M x F NPT 3/8” 3.70 2.38 2.75 1.13
FF90588-08 M x F NPT 1/2” 3.70 2.38 2.75 1.13
FF90588-12 M x F NPT 3/4” 3.80 2.72 3.40 1.43
FF90588-16 M x F NPT 1” 4.50 3.00 4.00 1.71
FF90588-20 M x F NPT 1-1/4” 6.22 3.01 4.05 1.83
FF90588-24 M x F NPT 1-1/2” 6.22 3.24 4.35 2.01
FF90588-32 M x F NPT 2” 6.22 3.52 5.13 2.38
PArT
NuMBEr CONNECTiONs siZE X Y Z
FF90589-04 F x F x F NPT 1/4” 3.70 2.38 2.25
FF90589-06 F x F x F NPT 3/8” 3.70 2.38 2.25
FF90589-08 F x F x F NPT 1/2” 3.70 2.38 2.25
FF90589-12 F x F x F NPT 3/4” 3.80 2.72 2.98
FF90589-16 F x F x F NPT 1” 4.50 3.00 3.34
FF90589-20 F x F x F NPT 1-1/4” 6.20 3.78 3.65
FF90589-24 F x F x F NPT 1-1/2” 6.20 4.15 4.00
FF90589-32 F x F x F NPT 2” 6.20 4.75 4.76

Service
. Working pressure: 500
psig bottom inlet@ 70oF; 100 psig side inlets

. Temperature range: -40oF
+ 300oF

.
Orifice diameters:
1/4” = .440”,
3/8” = .500”,
1/2” = .500”

.
Vacuum rating: Full

.
For: Water, oils and gases

Note: Not steam rated.

Features/Benefits
.
Forged brass body

.
Blowout proof stem

.
Chrome plated brass ball

.
Double o-ring stem seal

.
Tamper proof design

.
Floating ball design

.
Standard steel handle

.
1/4 turn - full on/off

Applications
.
Vacuum service

.
Industrial service

.
Machine/engine coolant

.
Water service

.
Fuel tank - gasoline/

diesel

Service
.
Working pressure: 600 psig WOG @ 70oF

.
Temperature range:

-40oF + 300oF

.
Orifice diameters: 1/4”=.44”, 3/8”=.50”, 1/2”=.50”, 3/4”=.69, 1”=.88, 1-1/4”= 1.18, 1-1/2”=1.57, 2”= 1.89

.
Vacuum rating: Full

.
For: Water, oils and gases

Note: Not steam rated.

Brass Products
Brass Ball Valves
Brass instrumentation 3-Way Ball Valve

Features/Benefits

.
Brass bar stock body

.
Blowout proof stem

.
Nickel plated ball

.
Viton stem seal

.
Double o-ring stem seal

-never needs tightening

.
Metal retainer seal

.
Center off position

.
Seals: Ball seats = teflon, stem seals = 2 o-rings (Viton & Buna-n)

PArT
NuMBEr CONNECTiONs siZE X Y Z
FF90597-02 F x F NPT 1/8” 0.92 0.92 2.12
FF90597-04 F x F NPT 1/4” 0.92 0.92 2.12
FF90597-06 F x F NPT 3/8” 1.10 1.10 2.59
FF90597-08 F x F NPT 1/2” 1.19 1.19 2.59
FF90598-02 Compression 1/8” 0.92 0.92 2.12
FF90598-04 Compression 1/4” 0.92 0.92 2.12
FF90598-06 Compression 3/8” 1.10 1.10 2.59
FF90598-08 Compression 1/2” 1.19 1.19 2.59

Applications

.
Vacuum service

.
Industrial service

.
Center off position

.
Water service

.
Panel mounting

Services

. Working pressure: 1/8” & 1/4”=1500 psig @ 70oF 3/8” & 1/2”= 1,000 psig @ 70oF (side port inlet) 1000 psig (bottom port inlet)
. Temperature range:
-40oF + 300oF

.
Orifice diameters: 1/8” & 1/4”=.250” 3/8” & 1/2”=.340”

.
Vacuum rating: Full

.
For: Water, oils and gases

.
Panel mount hole size: 9/16” ID

Note: Not steam rated.

Brass Products
Brass Ball Valves
Brass instrumentation 2-Way 90 Degree Ball Valve

Features/Benefits
.
Brass bar stock body

.
Blowout proof stem

.
Nickel plated brass ball

.
Double o-ring stem seal

.
Metal retainer seal

.
90o configuration

eliminates fittings

. Seals: Ball seats = teflon, stem seals = 2 o-rings (Viton & Buna-n)
PArT
NuMBEr CONNECTiONs siZE X Y Z
FF90595-02 F x F NPT 1/8” 0.92 0.38 2.12
FF90595-04 F x F NPT 1/4” 0.92 0.38 2.12
FF90595-06 F x F NPT 3/8” 1.10 0.75 2.59
FF90595-08 F x F NPT 1/2” 1.19 0.75 2.59
FF90596-02 Compression 1/8” 0.92 0.38 2.12
FF90596-04 Compression 1/4” 0.92 0.38 2.12
FF90596-06 Compression 3/8” 1.10 0.75 2.59
FF90596-08 Compression 1/2” 1.19 0.75 2.59

Applications Service
.
Vacuum service . Working pressure:

.
Industrial service 1/8” & 1/4”=1500 psig @ 70oF 3/8” & 1/2”= 1,000

.
Water service psig @ 70oF (side port

.
Panel mount inlet) 1000 psig (bottom port inlet)

. Temperature range: -40oF
+ 300oF
.
Orifice diameters: 1/8” & 1/4”=.250” 3/8” & 1/2”=.340”

.
Vacuum rating: Full

.
For: Water, oils and gases

.
Panel mount hole size: 9/16” ID

Note: Not steam rated.

Brass Products
Brass Ball Valves
Brass Mini-instrumentation 2-Way 90 Ball Valve

Features/Benefits
.
Brass bar stock body

.
Blowout proof stem

.
Nickel plated ball

.
Viton stem seal

.
Standard metal handle

.
Floating ball design

.
1/4 turn - full on/off

Brass instrumentation 2-Way Ball Valve

Features/Benefits
.
Brass bar stock body

.
Blowout proof stem

.
Nickel plated ball

.
Viton stem seal

.
Metal retainer seal

.
Seals: Ball seats = teflon, stem seals = 2 o-rings (Viton & Buna-n)

PArT NuMBEr CONNECTiONs siZE X Y Z
FF90590-02 FF90590-04 FF90591-02 FF90591-04 FF90592-02 FF90592-04 M x F NPT M x F NPT M x M NPT M x M NPT F x F NPT F x F NPT 1/8” 1/4” 1/8” 1/4” 1/8” 1/4” 1.13 1.13 1.13 1.13 1.13 1.13 0.75 0.81 0.75 0.81 0.75 0.85 1.25 1.25 1.25 1.25 1.25 1.25

Applications
.
Vacuum service

.
Industrial service

.
Coolant service

.
Water service

.
Compact shut off

installations
.
Low cost instrumentation

.
Hose shut off

PArT
Service
.
Working pressure: 1,000 psig WOG @ 70oF

.
Temperature range:

-40oF + 300oF
.
Orifice diameters: 1/8” & 1/4”=.250”

.
Vacuum rating: Full

.
For: Water, oils and gases

Note: Not steam rated.

NuMBEr CONNECTiONs siZE X Y Z
FF90593-02 F x F NPT 1/8” 0.92 0.92 1.25
FF90593-04 F x F NPT 1/4” 0.92 0.92 1.25
FF90593-06 F x F NPT 3/8” 1.10 1.10 1.42
FF90593-08 F x F NPT 1/2” 1.19 1.90 1.42
FF90594-02 Compression 1/8” 0.92 0.92 1.25
FF90594-04 Compression 1/4” 0.92 0.92 1.25
FF90594-06 Compression 3/8” 1.10 1.10 1.42
FF90594-08 Compression 1/2” 1.46 1.46 1.42

Applications
.
Vacuum service

.
Industrial service

.
Water service

.
Panel mounting

Service
. Working pressure: 1/8” & 1/4”=1500 psig @ 70oF 3/8” & 1/2”=1000
psig @ 70oF
Service (cont)
.
Temperature range: -40oF

+ 300oF

.
Orifice diameters: 1/8” & 1/4”=.250” 3/8” & 1/2”=.375”

.
Vacuum rating: Full

.
For: Water, oils and gases

.
Panel mount hole size: 9/16” ID

Note: Not steam rated.

Brass Products
Special Adapters

MAlE MAlE
Turbocharger
L
sTrAigHT PiPE CATAlOg THrEAD THrEAD NuMBEr

Dl
Discharge Connector
D
1 AC-811 3/4 1408 1-3/8 .719 3.25 30° Flare Tube

HOsE CATAlOg
WiperTee
i.D. NuMBEr M M1 N
1/4 1410 0.88 1.00 1.02
N

TuBE iNVErTED CATAlOg
Transmission
L
O.D. NuT NuMBEr

l
Oil Coolant
5/16 5/16 1428 1/2 4.50
line Adapter
3/8 3/8 1429 5/8 4.50

sAE 45° MAlE
Truck Oil line Extended
TuBE PiPE CATAlOg siZE THrEAD NuMBEr

Dl
sAE 45° Flare Fitting
D
3/8 1/4 1432 5/8 .282 1.90
(Replaces Roto Master
No. 10-35)

Refer to safety information regarding

Brass Products

proper selection of tubing on page 1.
Special Adapters
sTrAigHT
Ford Transmission
TuBE MAlE PiPE CATAlOg
O.D. THrEAD NuMBEr M N
Elbow
5/16–28 1/8–27 1437 .94 .47
Includes O-Rings.

TuBE THrEAD THrEAD CATAlOg
Power steering Male
L
O.D. A B NuMBEr

Dl
37° JiC Adapter
1/4 7/16–20 9/16–18 1440 9/16 .172 1.42

(Brass) D
3/8 9/16–18 5/8–18 1439 5/8 .266 1.49
Includes O-Rings.
AB
iNVErTED
Metric Power

steering Adapter

B TuBE THrEAD THrEAD CATAlOg
O.D. A B NuMBEr C

l
3/8 5/8–18 M14x1.5 1445 3/4 .266 1.18
D
Includes O-Rings.
A
3/8 5/8–18 M16x1.5 1446 3/4 .266 1.18 3/8 5/8–18 M18x1.5 1447 3/4 .266 1.18
L
iNVErTED MAlE CATAlOg
Ford Power

steering Fitting

B THrEAD A O-riNg B NuMBEr Dl

5/8–18 11/16–18 1444 3/4 .266 1.38
D
Includes O-Rings.
A
L

MAlE FEMAlE
restriction
PiPE PiPE CATAlOg THrEAD THrEAD NuMBEr

Dl
Pipe Adapter
D
1/8 1/8* 1512 1/2 .0625 0.75
(With .0625 Orifice)

* PTF short thread. NOTE: Other orifice sizes available
(special order only).

Brass Products
Special Adapters
Carburetor to Fuel line Adapter
(Ford)
For use with 59x4

Fuel line Adapter
L

D

L

AC Type Adapter

Adapter sAE 45° Flare
D

Refer to safety information regarding proper selection of tubing on page 1.
TuBE THrEAD MAlE PiPE CATAlOg
O.D. siZE THrEAD NuMBEr Dl

1/4 1/2–20 1/8 1513 9/16 .219 1.06
MAlE
iNVErTED MAlE PiPE THrEAD CATAlOg NuMBEr
D l
1/2-20 1/8 1514 1/2 .219 0.90

s.A.E. 45°
TuBE O.D. TuBE siZE CATAlOg NuMBEr
D l
1/4 1/4 1521 7/16 .188 1.09

sAE 45°
TuBE siZE iNVErTED MAlE CATAlOg NuMBEr
D l
1/4 3/16 1518 7/16 .189 1.03
1/4 1/4 1522 7/16 .189 1.03
3/8 5/16 1553 5/8 .234 1.34
3/8 3/8 1563 5/8 .282 1.38
3/8 7/16 1554 11/16 .282 1.40

iNV. MAlE CATAlOg sEAT THrEAD NuMBEr

Dl
3/8 7/8-20 1596 1 .281 0.91

to inv. Flare
Carburetion inlet
(Steel)
L

D

Refer to safety information regarding

Brass Products
proper selection of tubing on page 1.
Special Adapters

FEMAlE MAlE PiPE CATAlOg THrEAD THrEAD NuMBEr
special steel Bushing

Dl
1-1/16-16UN-2A 1/8 7977 1-1/8 .328 .94 1-1/16-16UN-2A 3/8 7978 1-1/8 .562 .94

TuBE THrEAD CATAlOg
Male JiC 37° Flare
O.D. B NuMBEr

Dl
to Metric O-ring
D
3/8 M14x1.5 M41157x6x14 3/4 .266 1.62
Port Adapter
3/8 M16x1.5 M41157x6x16 3/4 .266 1.62
Steel (with o-ring)
3/8 M18x1.5 M41157x6x18 3/4 .266 1.62
Application:
GM power steering with
Saginaw steering and rack and pinion steering systems.
Includes O-Ring.

TuBE THrEAD CATAlOg
Ford Nut
L
siZE siZE NuMBEr

Dl
1/4 1/2-20 59x4 1/2 .258 0.64 59x4 for 3/16" tube, use 6100x3) For use with 1513 (Nut similar to
D
Transmission Coolant line Adapters (gMC)
AC8111 (steel) Connector
Application:
PTT Thread 30° tube to male pipe adapter for diesel engines.

iNV. iNV. CATAlOg FEMAlE MAlE NuMBEr

Dl
3/8 5/16 7915 3/4 .250 1.00
D
(5/8-18) (1/2-20)
5/16 3/8 7916 5/8 .220 0.94 (1/2-20) (5/8-18)
TuBE MAlE CATAlOg siZE PiPE NuMBEr

Dl
1 (1-5/16–14) 1 C9200 1-3/8 .844 2.04
D
1 (1-5/16–14) 3/4 C9240 1-3/8 .800 1.84

Brass Products Refer to safety information regarding proper selection of tubing on page 1.

Hydraulic Brake Products
Adapters can be used to the steel brake line. Thread adapt standard steel brake size can be determined by lines to the different size measuring with a U.S. or ports used in dual master Metric screw pitch gauge.
9/16 - 20 Port cylinders. The tube O.D. See pages 10 to 14. is the outside diameter of
7910 Adapter
Standard 3/16" Steel Line
sTANDArD iNVErTED FlArE TuBE AND THrEAD siZE
Tube Size 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1
Thread Size 5/16–28 3/8–24 7/16–24 1/2–20 5/8–18 11/16–18 3/4–18 7/8–18 1-1/16–16 1-3/16–16 1-5/16–16
standard Tube Nut
(Steel)
TuBE siZE CATAlOg NuMBEr
1/8 105x2
3/16 105x3
1/4 105x4
5/16 105x5
3/8 105x6
3/8 105x6x7*
7/16 105x7
1/2 105x8
5/8 105x10
3/4 105x12
7/8 105x14
1 105x16

*11/16–18 Thread
long Tube Nut
(Steel)
TuBE THrEAD CATAlOg
O.D. siZE NuMBEr
3/16 3/8–24 7896x3
1/4 7/16–24 7896x4
Dual Master Cylinder Adapter
iNVErTED MAlE THrEAD
(Exceptions Noted)
3/16 (9/16–18)
3/16 (9/16–18)
3/16 (9/16–20)
3/16
1/4
7/16–20
1/4 (9/16–18)
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
3/8 NPTF
3/8
iNVErTED FEMAlETHrEAD
(Exceptions Noted)
3/16
3/16 (1/2–20)
3/16
1/4
3/16
1/4
1/4
5/16.
3/16
3/16
3/16 (9/16–18)
1/4
1/4
5/16
3/8
5/16
5/16
CATAlOg
NuMBEr

7911
7913
7910
7828
7818
7732*
7908
7917
7817*
7909
7912
7727*
7829
1074*
7915
7771
7916
. Seat may be used for 3/16”, 1/4”, 5/16” Tube Connection with 1/2-20 Thread. *Seals On Hex Face (E)
Dual Master Cylinder Adapter
BuBBlE FlArE iNVErTED CATAlOg
MAlETHrEAD FEMAlETHrEAD NuMBEr

3/16 3/16 1441 5/16 3/16 7897

Brass Products
Hydraulic Brake Products
B
C
Towed Trailer A
strap Tee Brake Tee
Assembly

CATAlOg A B C NuMBEr NuMBEr
iNVErTED sEAT MAlETHrEAD CATAlOg iNV. sEAT BOlT HOlE
3/16 (3/8–24) 3/16 (1/2–20) 3/16 (3/8–24) 3/16 (3/8–24) 3/16 inv. (3/8–24) 1/2–20 inv. 7900 7906 3/16 (3) 1/4 (3) 11/32 11/32 7812 7765*
3/16 (9/16–18) 3/16 (3/8–24) 3/16 inv. (9/16–18) 7933 *Has flat strap
3/16 (9/16–20) 3/16 (3/8–24) 3/16 inv. (9/16–20) 7905

3/16 (7/16–24) 1/4 (7/16–24) 3/16 (3/8–24) 3/16 (3/8–24) 1/4 inv. (7/16–24) 1/4 inv. (7/16–24) 7914 7901 Brake Adapter

1/4 (9/16–18) 3/16 (3/8–24) 1/4 inv. (9/16–18) 7904

1/4 (7/16–24) 1/4 (7/16–24) 1/4 inv. (7/16–24) 7898 iNV. sEAT BOlT HOlE CATAlOg NuMBEr

1/4 19/32 7709
Metric Hydraulic rear Axle Tee
Brake Products
How to Measure

iNV. BOlT HOsE END CATAlOg Metric Threads sEAT HOlE POrT NuMBEr
Metric threads are measured 22mm and dimension “B” 3/16 (2) 9/32 3/8–24 7805 and specified by the thread (crest to crest distance) diameter in millimeters and is 1.5mm, then the metric the pitch in millimeters per thread size is M22 x 1.5. thread. If dimension “A” is Adapter standard
to Metric Bubble

FEMAlE sTD. MAlE BuBBlE CATAlOg Fl. sEAT Fl. TuBE NuMBEr
3/16" (3/8-24 thread) 3/16" (10x1.25 thread) 7970
Metric Adapter
Used on Fiat applications when converting 3/16" (3/8–24) inverted flare brake lines to 3/16" (10x1.25) metric thread bubble flare.
BuBBlE MAlE TuBE O.D./ CATAlOg THrEAD FEMAlETHrEAD NuMBEr

M10 x 1.0 3/16 (3/8–24) 1442* Adapter standard
M11 x 1.5 3/16 (M10 x 1.0) 7935** to Metric Bubble

M12 x 1.0 3/16 (M10 x 1.0) 7936** FEMAlE iNV. MAlE METriC BuBBlE CATAlOg
M13 x 1.5 3/16 (M10 x 1.0) 7937** Fl. sEAT Fl. THrEAD NuMBEr

*Use S Series Brake Lines. (standard flare) 3/16" (3/8-24 thread) 13x1.5 7972
**Use SJ Series Steel Brake Lines. (standard flare) 3/16" (3/8-24 thread) 12x1.0 7974
Used on Fiat applications when converting 3/16" (3/8–24) inverted flare brake lines to
3/16" (10x1.25) metric thread bubble flare.
Metric Adapter

iNVErTED MAlE TuBE O.D./ THrEAD FEMAlE THrEAD CATAlOg NuMBEr
M10 x 1.0 3/16 (3/8–24) 1443*
*Use S Series Brake Lines. (standard flare)
**Use SJ Series Steel Brake Lines. (standard flare)

Brass Products
Hydraulic Brake Products
Brake line unions DEsCriPTiON CATAlOg NO.
for Domestic and 3/16" line to 3/16" line (3/8–24 thread), (Standard Flare) ‘S’ Series 302x3
imported Vehicles 1/4" line to 1/4" (7/16–24 thread), (Standard Flare) ‘S’ Series 302x4

5/16" line to 5/16" line (1/2–20 thread), (Standard Flare) ‘S’ Series 302x5

3/8" line to 3/8" line (5/8–18 thread), (Standard Flare) ‘S’ Series 302x6

British line to British line (3/8–24 thread), (ISO flare) ‘SB’ Series (Steel) 7940

European line to European line (10–1.0mm thread), (Bubble Flare) ‘SC’ Series (Steel) 7941

Japanese line to Japanese line (10–1.0mm thread), (Standard Flare) ‘SJ’ Series (Brass) 7934A
For joining Edelmann 6300 series metric thread 7975
bubble flare 3/16" brake lines (10-1.0mm thread) (brass)

Refer to safety information regarding

Plastic Products
proper selection of tubing on page 1.

Molded Compression Tube Products

Molded Compression Tube Products
* Celcon is a registered trademark of Ticona.
** KYNAR is a registered trademark of Elf Atochem North America, Inc.

Operating temperatures of Eaton con nectors are regulated by ambient and fluid temperatures, type of fluid being carried, tubing type and conditions of mechanical abuse. Pressures in excess of above specifications in all connector sizes should be tested by the customer in the particular application.
Sizes:
Available in sizes 1/8" through 3/4" tube OD (7/8" tube OD and metric tube sizes available on request from Technical Support at 1-888-258-0222.
Materials:
Molded as standard in two materials: nylon and polypropylene
Nylon characteristics:
. good resistance to
organic solvents, oils, and gasoline

. excellent impact
resistance

. tolerant to repeated
steam for wash down and longtime weathering

. F.D.A. and N.S.F. listed

. operating temperatures -40°F to 200°F (-40°C to 93°C) – not to exceed

temperature specification of tubing Polypropylene characteristics:

. good chemical and
corrosion resistance

. opaque

. 20% glass filled

. N.S.F. listed

. operating temperatures -30°F to 200°F (-34°C to 93°C) – not to exceed

temperature specification of tubing

Available on request in two materials: Celcon.* (acetal copolymer) or KYNAR.** (polyvinylidene fluoride)
Styles:
Available in two standard styles:
Ferrule Nut (integral nut
and sleeve for soft tubing
to 50 PSIw)
. features ferrule and nut
molded as a single part, eliminating the need for a two-piece assembly

Gripper Nut with separate plastic sleeve (for sure-grip with plastic tubing up to
220 PSIw)
. for higher pressure
applications

Features and Benefits:
. leak-free performance
. high integrity in both mechanical and acoustical vibrations
. ten styles and over 400 part number configurations to meet your needs
. easy assembly – no special tools or tube preparation necessary
. reliability in side-loaded applications allows for compact plumbing
. For use with PT200,
PT240, and TP160
plastic tubing

. connectors come fully assembled – for your convenience
. very low resistance to media flow resulting from material and internal surfaces

. no metal parts to corrode or present a safety hazard with aggressive chemicals

. ISO 9001 Certified

Plastic Products

Molded Compression Tube

Ferrule nut with integral sleeve low pres-

Ferrule nut with plastic gripper for use with

Products

sure application soft plastic tubing plastic tubing for sure grip
Assembly Instructions
Ordering Information
* Celcon is a registered trademark of Ticona.
** KYNAR is a registered trademark of Elf Atochem North America, Inc.

Maximum Operating Pressure:
Ferrule Nut series = 50 PSi max
Gripper Nut series = 220 PSi max

Operating pressures of Eaton molded compression products are regulated by ambient and fluid temperatures, type of fluid being carried, tubing type and conditions of mechanical
abuse. Pressures in excess
of above specifications in all fitting sizes should be tested by the customer for their particular application.
Used with:

Plastic tubing: TP160, PT200, and PT240.
Tube inserts are recommended for optimal performance with PT200 tubing.
Molded compression connector are available in nylon and in polypropylene. They are also available by special order in KYNAR** (polyvi
nylidene fluoride) or Celcon* (acetal copolymer). To order fittings in KYNAR or Celcon,
call Technical Support at 1-888-258-0222. Refer to
Chemical Resistance Chart, pages 22-26. For detailed
information on chemical compatibility, call Technical Support at1-888-258-0222. General material characteristics are as follows:
Nylon, F.D.A. and N.S.F.
listed, has good resistance to organic solvents, oils and gasoline. Good strength at
high temperatures. Cold
and hot-water applications. Longtime weathering resistance. Good impact resistance, both single and repeated. Not recommended for use with bleach, acids, or chlorine.
Polypropylene, N.S.F.
listed, has good chemical resistance. Withstands continuous temperatures
up to 215°F (not to exceed
Temperature Range:
Nylon = -40°F to +200°F (-40°C to +93°C)
Polypropylene = -30°F to +200°F (-34°C to +93°C)
Ranges are at maximum
operating pressures (refer to
tubing temperature range).
The overlap of temperature ranges of the individual components will decide the actual temperature range of the assembly.
Assembly Instructions:
. Cut tubing to desired
length; be sure the tube
end is cut properly (maxi
mum 10° cutting angle
allowed).
temperature specification
of tubing). Unaffected by most weak acids, alkalies, alcohols and ketones. Do not use with oxidants or
strong acids or in continuous
sunlight. 20% glass filled for
improved stiffness.
KYNAR, an F.D.A. and N.S.F. listed polyvinylidene fluoride, has outstanding chemical resistance for handling highly corrosive fluids.
Celcon, an acetal copo
lymer, N.S.F. listed and
U.S.D.A. and F.D.A. listed for coffee, milk and antibiotics,
has high tensile strength and good impact resistance over a broad temperature range. Translucent white color. Not affected by continuous hot-water service
and works smoothly with metal tubing. Celcon cannot be recommended for
continuous exposure to
solutions with a chlorine concentration greater than 1
ppm. Suggested maximum
continuous-use temperature
is 220°F in air and 180°F in water (not to exceed temperature specification of
. Insert the tubing through the back of the nut all
the way through the nut assembly to the tube stop in the connector body (see
illustration). If the tubing
does not enter the nut easily, loosen the nut one turn and then insert the tubing all the way to the tube stop in the fitting body.
.
Turn the nut to hand-tight.

.
Tighten the nut an additional 2 to 2-1/2 turns past hand-tight or until the nut bottoms against the connector body, whichever comes first.

.
All nuts must be retightened when the system reaches projected operating temperature.

tubing). Unaffected by most inorganics, except sulfuric,
nitric and hydrochloric acids. Should not be continuously
exposed to sunlight.
Most connectors can be ordered with a GRiPPER
style nut. Fittings with a
GRiPPER style nut are capable of handling greater pressure than those with standard style nut. See page
128.
For ordering connectors with
‘GRiPPER’ nut, add ‘G’ to the end of the part number
(example: 1568x4x4G or 1568Px4x4G). Some connectors are NOT available with the GRiPPER style nut, while others are ONLY available with the GRiPPER style nut, as noted on pages 130-131.
For more information, call
Technical Support at 1-888-258-0222.
Note:
it is not necessary to disassemble the connector for assembly. Merely insert tubing to stop and tighten compression nut.

Plastic Products . Not available with GRIPPER style nut Sold ONlY with GRIPPER style nut

Molded
To order with ‘GRIPPER’ nut, add ‘G’ to the Compression Tube end of the part # (Except where noted!) Products Example: 1568x4x4G or 1568Px4x4G
Tube 1/8 1/4 5/16 3/8 1/2 5/8 3/4
O.D. (125) (.250) (.312) (.375) (.500) (.625) (.750)

Tube Thread Size 5/16–24 7/16–20 1/2–20 5/8–20 3/4–20 7/8–20 1-1/16–20

MAlE CATAlOg CATAlOg
Male Connector
TuBE PIPE NuMBEr NuMBEr
O.d. ThrEAd NylON POlyPrOPylENE l d

1/8 1/8 1568x2. 0.88 0.13 7/16 1/4 1/8 1568x4 1568Px4 0.99 0.26 5/8 1/4 1/8 1568x4G 1568Px4G 0.99 0.26 5/8 1/4 1/4 1568x4x4 1568Px4x4 1.17 0.26 5/8

1/4 1/4 1568x4x4G 1568Px4x4G 1.17 0.26 5/8
1/4 3/8 1568x4x6G 1568Px4x6 1.20 0.26 13/16
5/16 1/8 1568Px5 1.00 0.32 11/16
5/16 1/4 1568x5x4 1568Px5x4 1.19 0.32 11/16
3/8 1/8 1568x6x2 1568Px6x2 1.14 0.38 13/16
3/8 1/8 1568Px6x2G 1.14 0.38 13/16
3/8 1/4 1568x6 1568Px6 1.30 0.38 13/16
3/8 1/4 1568x6G 1568Px6G 1.30 0.38 13/16
3/8 3/8 1568x6x6 1568Px6x6 1.34 0.38 13/16
3/8 3/8 1568x6x6G 1.34 0.38 13/16
3/8 1/2 1568x6x8 1568Px6x8 1.59 0.38 59/64
3/8 1/2 1568x6x8G 1568Px6x8G 1.59 0.38 59/64
1/2 1/8 1568x8x2G 1.23 0.51 15/16
1/2 1/4 1568x8x4 1568Px8x4 1.42 0.51 15/16
1/2 1/4 1568Px8x4G 1.42 0.51 15/16
1/2 3/8 1568x8 1568Px8 1.47 0.51 15/16
1/2 3/8 1568x8G 1568Px8G 1.47 0.51 15/16
1/2 1/2 1568x8x8 1568Px8x8 1.61 0.51 15/16
5/8 3/8 1568x10x6G 1.50 0.63 1-1/16
5/8 1/2 1568x10G 1568Px10G 1.66 0.63 1-1/16
3/4 3/4 1568x12x12G 1568Px12x12G 1.92 0.76 1-5/16

CATAlOg CATAlOg TuBE NuMBEr NuMBEr
Bulkhead union
O.d. NylON POlyPrOPylENE l I d

1/4 1574x4 1.45 0.88 0.26 5/8 3/8 1574x6 1574Px6 1.78 1.03 0.38 13/16 1/2 1574x8 1.89 1.04 0.51 15/16 3/4 1574x12G 1574Px12G 2.41 1.35 0.76 1-5/16

Plastic Products . Not available with GRIPPER style nut Sold ONlY with GRIPPER style nut
Molded

Compression Tube Products

CATAlOg CATAlOg
union Connector

D1 TuBE NuMBEr NuMBEr
DF

O.d. NylON POlyPrOPylENE l F

1/4 1562x4 1562Px4 0.98 0.23 5/8 1/4 1562x4G 1562Px4G 0.98 0.23 5/8 5/16 1562x5 1.03 0.28 11/16 5/16 1562x5G 1562Px5G 1.03 0.28 11/16 3/8 1562x6 1562Px6 1.23 0.30 13/16
3/8 1562x6G 1562Px6G 1.23 0.30 13/16
1/2 1562x8 1562Px8 1.44 0.48 15/16
1/2 1562Px8G 1.44 0.48 15/16
5/8 1562x10G 1562Px10G 1.50 0.50 1-1/16
3/4 1562x12G 1562Px12G 1.75 0.64 1-5/16

TuBE O.d. TuBE O.d. CATAlOg NuMBEr NylON CATAlOg NuMBEr POlyPrOPylENE l d
d1
1/4 1/8 1562Px4x2. 0.92 0.26 5/8 0.13
5/16 1/4 1562x5x4. 1.00 0.32 11/16 0.26
3/8 1/4 1562x6x4G 1.19 0.38 13/16 0.26
1/2 3/8 1562Px8x6 1.33 0.51 15/16 0.38
5/8 1/2 1562Px10x8G 1.47 0.63 1-1/16 0.51

FEMAlE CATAlOg CATAlOg
Female Connector

TuBE PIPE NuMBEr NuMBEr
O.d. ThrEAd NylON POlyPrOPylENE l d

1/4 1/8 1566x4 0.92 0.23 9/16 1/4 1/8 1566x4G 0.92 0.23 9/16 1/4 1/4 1566x4x4 1566Px4x4 1.09 0.22 11/16 1/4 1/4 1566x4x4G 1.09 0.22 11/16

5/16 1/4 1566x5x4 1.22 0.28 11/16
5/16 1/4 1566x5x4G 1.22 0.28 11/16
3/8 1/4 1566x6 1.20 0.36 11/16
3/8 3/8 1566x6x6 1566Px6x6 1.20 0.36 13/16
3/8 3/8 1566x6x6G 1.20 0.36 13/16
3/8 1/2 1566x6x8 1566Px6x8 1.27 0.34 1-3/64
3/8 1/2 1566x6x8G 1566Px6x8G 1.27 0.34 1-3/64
1/2 3/8 1566x8 1.23 0.47 13/16
1/2 3/8 1566x8G 1.23 0.47 13/16
1/2 1/2 1566x8x8 1566Px8x8 1.30 0.48 15/16

Plastic Products . Not available with GRIPPER style nut Sold ONlY with GRIPPER style nut

Molded Compression Tube Products

FEMAlE CATAlOg CATAlOg TuBE PIPE NuMBEr NuMBEr
Female Elbow

ACrOss
O.d. ThrEAd NylON POlyPrOPylENE M N d FlATs F
1/4 1/8 N/A 0.81 .75 0.26 35/64 25/64 1/4 1/4 1570x4x4 0.81 .97 0.26 11/16 13/32 5/16 1/4 1570x5x4G 1570Px5x4G 0.94 1.00 0.32 11/16 7/16 3/8 3/8 1570x6x6 1570Px6x6 0.91 1.03 0.38 13/16 9/16

Male Elbow

D

TuBE MAlE PIPE CATAlOg NuMBEr CATAlOg NuMBEr ACrOss
O.d.. Thd. NylON POlyPrOPylENE M N d d1 FlATs F
1/8 1/8 1569Px2. 0.56 0.63 0.11 0.20 1/4
1/4 1/8 1569x4 0.81 0.81 0.22 0.25 3/8
1/4 1/8 1569x4G 0.81 0.81 0.22 0.25 3/8
1/4 1/4 1569x4x4 1569Px4x4 0.81 1.02 0.22 0.28 3/8
1/4 1/4 1569x4x4G 1569Px4x4G 0.81 1.02 0.22 0.28 3/8
1/4 3/8 1569x4x6 0.84 1.09 0.23 0.38 9/16
3/8 1/4 1569x6 1569Px6 0.94 1.03 0.30 0.31 37/64
3/8 1/4 1569x6G 1569Px6G 0.94 1.03 0.30 0.31 37/64
3/8 3/8 1569x6x6 1569Px6x6 0.94 1.09 0.34 0.38 9/16
3/8 3/8 1569x6x6G 0.94 1.09 0.34 0.38 9/16
1/2 1/4 1569x8x4G 1.06 1.09 0.39 0.31 11/16
1/2 3/8 1569x8 1569Px8 1.09 1.13 0.39 0.31 11/16
1/2 3/8 1569x8G 1.09 1.13 0.39 0.31 11/16
1/2 1/2 1569x8x8 1569Px8x8 1.09 1.28 0.47 0.36 11/16
1/2 1/2 1569x8x8G 1569Px8x8G 1.09 1.28 0.47 0.36 11/16
5/8 1/2 1569x10G 1569Px10G 1.25 1.44 0.52 0.50 13/16

Plastic Products . Not available with GRIPPER style nut Sold ONlY with GRIPPER style nut

Molded Compression Tube Products

TuBE CATAlOg NuMBEr CATAlOg NuMBEr ACrOss
O.d. NylON POlyPrOPylENE l d N FlATs F
1/8 1564x2. 1.11 0.11 0.52 1/4
1/4 1564x4 1564Px4 1.44 0.22 0.72 23/64
1/4 1564x4G 1.44 0.22 0.72 23/64
5/16 1564x5G 1564Px5G 1.61 0.28 0.83 7/16
3/8 1564x6 1564Px6 1.91 0.30 0.97 17/32
3/8 1564Px6G 1.91 0.30 0.97 17/32
1/2 1564x8 1564Px8 2.13 0.48 1.03 11/16
1/2 1564x8G 2.13 0.48 1.03 11/16
5/8 1564x10G 2.56 0.50 1.25 13/16
3/4 1564x12G 3.11 0.62 1.56 1-1/16

TuBE CATAlOg NuMBEr CATAlOg NuMBEr ACrOss
O.d. NylON POlyPrOPylENE M d FlATs F
1/4 1565x4 0.81 0.22 3/8
1/4 1565x4G 0.81 0.22 3/8
3/8 1565x6 1565Px6 0.94 0.34 9/16
3/8 1565x6G 1565Px6G 0.94 0.34 9/16
1/2 1565x8 1565Px8 1.06 0.39 43/64
1/2 1565x8G 1.06 0.39 43/64
5/8 1565x10G 1.25 0.52 13/16

TuBE 0.d. MAlE PIPE Thd. CATAlOg NuMBEr NylON CATAlOg NuMBEr POlyPrOPylENE l d N d1 ACrOss FlATs F
1/4 1/8 1572x4 1.45 0.22 0.75 0.25 3/8
1/4 1/8 1572x4G 1.45 0.22 0.75 0.25 3/8
1/4 1/4 1572x4x4x4 1.45 0.22 0.92 0.31 3/8
1/4 1/4 1572x4x4x4G N/A 1.45 0.22 0.92 0.31 3/8
5/16 1/4 1572Px5x5x4 1.61 0.30 0.98 0.31 27/64
3/8 3/8 1572x6x6x6 1.91 0.36 1.11 0.38 1/2

1/2 1/2 1572x8x8x8 2.19 0.48 1.31 0.48 5/8
Plastic Products . Not available with GRIPPER style nut Sold ONlY with GRIPPER style nut

Molded Compression Tube Products
MAlE CATAlOg CATAlOg TuBE PIPE NuMBEr NuMBEr ACrOss
O.d. Thd. NylON POlyPrOPylENE l d N FlATs F

1/4 1/8 1571x4 1.47 .22 .73 3/8
1/4 1/4 1571x4x4x4 1.67 .22 .72 23/64
1/4 1/4 1571x4x4x4G 1.67 .22 .72 23/64
5/16 1/4 1571x5x4x5G 1571Px5x4x5 1.81 .28 .81 7/16
3/8 3/8 1571x6x6x6 1571Px6x6x6 2.03 .34 .97 1/2
1/2 3/8 1571x8 2.27 .47 1.11 5/8
1/2 3/8 1571Px8G 2.27 .47 1.11 5/8
1/2 1/2 1571x8x8x8G 2.41 .47 1.11 39/64
3/4 1/2 N/A 1571Px12G 3.17 .64 1.55 1-1/16

Compression Nut Ferrule Nuts with Integral Sleeve
CATAlOg CATAlOg TuBE NuMBEr NuMBEr
Ferrule Nuts with Integral Sleeve O.d. NylON POlyPrOPylENE

ld

1/4 1561x4 5/8 0.63 0.26
5/16 1561x5 11/16 0.69 0.32
3/8 1561x6 13/16 0.75 0.38
1/2 1561x8 15/16 0.88 0.51

With Plastic Gripper
With Plastic Gripper

CATAlOg CATAlOg TuBE NuMBEr NuMBEr

ldO.d. NylON POlyPrOPylENE

D 1/4 1561x4G 5/8 0.69 0.26 3/8 1561x6G 13/16 0.73 0.38 1/2 1561x8G 1561Px8G 15/16 0.88 0.51

Insert

TuBE O.d. CATAlOg NuMBEr NylON CATAlOg NuMBEr POlyPrOPylENE E l d
1/4 1584x4 0.25 0.38 0.12
5/16 1584x5 0.31 0.40 0.14
3/8 1584x6 0.37 0.50 0.20
1/2 1584x8 0.49 0.56 0.30

Plastic Products

Molded Compression Tube Products

CATAlOg CATAlOg
Cap Nut
TuBE NuMBEr NuMBEr
O.d. NylON POlyPrOPylENE l

1/8 1529x2 0.52 7/16 1/4 1529x4 1529Px4 0.63 5/8 3/8 1529x6 0.73 13/16 1/2 1529x8 1529Px8 0.88 15/16

Bulkhead Nut

KyNAr Check Valve

KYNAR** Check Valve Features and Benefits:
.
Viton. “O” Ring

.
Stainless Ball & Spring

.
Zero Leakage

.
Maximum Operating Temp. 180°F @ 220 PSI

.
Cracking Pressure 1 to 2.5 PSI

Viton is a registered trademark of DuPont Dow Elastomers
** KYNAR is a registered trademark of Elf Atochem North America, Inc.
TuBE O.d. CATAlOg NuMBEr NylON CATAlOg NuMBEr POlyPrOPylENE
1/4 1502x4 5/8
5/16 1502Px5 11/16
3/8 1502x6 13/16

MAlE PIPE sIzE N.P.T.F. CATAlOg NuMBEr KyNAr ONly l j
1/8 1531x2 1.00 0.09 7/16
1/4 1531x4 1.41 0.19 5/8
3/8 1531x6 1.50 0.25 13/16
1/2 1531x8 1.81 0.34 15/16

Refer to safety information regarding

Plastic Products
proper selection of tubing on page 1.
Plastic Products

straight Connector TuBE TuBE CATAlOg 3 Way Tee TuBE TuBE TuBE CATAlOg
I.d. A I.d. B NuMBEr I.d. A I.d. B I.d. C NuMBEr
A 1/8 1/8 1911
C 1/8 1/8 1/8 1916 B 1/8 3/16 1923

1/8 1/8 3/16 1917 1/8 1/4 1924
B 1/8 1/8 1/4 1918 3/16 3/16 1912
1/8 3/16 1/8 1939 1/4 3/16 1914 3/16 1/8 3/16 1940 1/4 1/4 1913 3/16 3/16 3/16 1902 1/4 3/8 1915 3/16 3/16 1/8 1920 5/16 5/16 1925 3/16 3/16 1/4 1921 3/8 3/8 1927 1/4 3/16 3/16 1942 1/4 1/4 1/4 1903 1/4 1/4 3/16 1943 5/16 5/16 5/16 1906 3/8 3/16 3/8 1944 3/8 1/4 3/8 1945 3/8 3/8 3/16 1907 3/8 3/8 1/4 1908 3/8 3/8 3/8 1922
TuBE I.d. CATAlOg TuBE TuBE TuBE CATAlOg universal Connector sIzE NuMBEr y Connector I.d. A I.d. B I.d. C NuMBEr

5/32–1/4–3/8 1901
C 3/16 3/16 3/16 1932 1/4 1/4 1/4 1935
A B 1/4 3/8 3/8 1936 5/16 5/16 5/16 1937 3/8 3/8 3/8 1938
Elbow Connector TuBE TuBE CATAlOg 4 Way Tee TuBE I.d. CATAlOg
I.d. A I.d. B NuMBEr All ENds NuMBEr
A
1/8 3/16 1928

3/16 1948 3/16 3/16 1929 B 3/16 1/4 1930 1/4 1/4 1931
universal Tee TuBE I.d. CATAlOg 5 Way Tee TuBE I.d. CATAlOg sIzE NuMBEr All ENds NuMBEr

5/32–1/4–3/8 1900

3/16 1949
Temperature Range:
-40°F to +350°F.
Material: Nylon 6/6
Not recommended for fuel line applications.

Refer to safety information on page 1.

Brass–
Nickel Plated

BSPP Products
BsPP Male To NPTF Female Adapter

A

BsPP Female To NPTF Male Adapter

MAlE BsPP FEMAlE NPTF ThrEAd CATAlOg NuMBEr h l sW (MM)
1/8 1/8 1150x2x2PP 0.27 0.67 14
1/4 1/4 1150x4x4PP 0.32 0.91 17
3/8 3/8 1150x6x6PP 0.35 0.96 22
1/2 1/2 1150x8x8PP 0.39 1.16 27

FEMAlE
MAlE BsPP NPTF ThrEAd CATAlOg NuMBEr h l sW (MM)
M5* 10-32. 1100x5MMxA 0.18 0.47 8
1/8 1/8 1100x2PPx2 0.37 0.77 14
1/4 1/4 1100x4PPx4 0.51 1.06 17
3/8 3/8 1100x6PPx6 0.51 1.08 19

*M5 has 0.8mm Thread Pitch. M5 seals with nylon washer, included.
.UNF thread

Refer to safety information

related Products
on pages 1.

Air Brake Products & Measuring Kits
Coiled Air Brake Tube Assemblies

Thread Measuring Kit
Weatherhead Part # TA-1002 Aeroquip Part # FT1341

Conforms to SAE J844 Type B and SAE J1131.
Conforms to DOT FMVSS
571.106.
. Spring guards zinc plated for maximum corrosion
resistance.
. Provides you with error
free installation.

. Preassembled for immediate installation.
CATAlOg TuBE MAlE NuMBEr O.d. PIPE
Maximum Working
Pressure:

150 PSi
Minimum Burst:
950 PSi.
Temperature Range:
-40°F to +200°F.
Color Coding:
Red for emergency
Blue for serviceBrass
end fittings with spring guards and 1/2" male pipe connections.
WOrKINg PIgTAIl lENgTh lENgTh

W1206* 1/2 1/2 12' 6"
W1212* 1/2 1/2 12' 12"
W1512* 1/2 1/2 15' 12"

*Each catalog number contains a coiled red assembly and a coiled blue assembly.
Measuring tube and pipe fitting threads can be a
most difficult task if not
completely understood. Tools needed include a thread pitch gauge, calipers and seat angle gauges. To aid you, Eaton
has a kit to fit your needs.
This handy kit includes:
. Thread Pitch Gauge (American and metric)
.
Inside/Outside Caliper (inches and millimeters)

.
2 Seat Angle Gauges (37°/45° and a 12°/30° )

.
International Measuring

and identification Guide
and Instruction Booklet
. Carrying Case for Easy and Convenient Storage

Related Products

CAUTION:
Sharp blade! Keep Assembly & Tool hands and fingers away from Cutting Equipment cutting surface!
Utility Tube Cutter
T-1430 Inner-Outer Reamer

Need to cut stainless steel tubing? This cutting tool is for you. It features an enclosed feed screw to eliminate clogging and jamming. Grooved rolls for close to flare cuts and a fold away reamer.
Reams both inside and outside edges of tube with three hollow ground tool steel cutters. Fluted body is shaped to fit comfortably in palm of hand.

Capacity:
1/8" to 1-1/8" O.D. Cuts hard and soft copper, aluminum, brass, carbon steel and stainless steel tubing.
Spare Parts:
T-1422R Replacement Cutting Wheel
Capacity:
3/16" to 1-1/2" O.D. Reams copper, brass, aluminum and other tubing.

Related Products
Tube Cutting Equipment
Plastic Tube Cutter
Weatherhead Part # T-135
Aeroquip Part # FT1356

T-138 Hose and Tube Cutter

T-191 Plastic Tube and Hose Cutter

An economical alternative to quality tube and hose cutting. This versatile tool is lightweight and durable for long service life.
Replacement Blade:
Weatherhead=T-135B Aeroquip=FT1356-2-1
One hand operation for quick, clean cuts through plastic or nylon compound tubing and solid or fiber-reinforced hose up to 1" O.D.
. Any wireless hose
or tubing.
.
Power steering hose

.
Air Conditioning hose

.
Air brake hose

.
Air system nylon tubing

(NT100)
.
Thermoplastic hose

.
Low pressure plastic tubing (PT200, PT230, PT240)

A tool designed to be small, only 2-7/8" long. The versatile T-191 offers quick and clean square cuts on 1/16" to 1/2" O.D. plastic tubing and non-wire reinforced hose. The T-191 can be either bench or wall mounted and offers the safety of closing automatically when not in use.

Refer to safety information on page 1.
Capacity:
Up to 1" I.D.
Note:
Not for use with wire-reinforced hose.
Replacement Blade: T-138B
Note:
Not for use with wire-reinforced hose.
Spare Parts:
T-191B Replacement Blade (one per package)

Refer to safety information

Related Products
on page 1.
Tube Bending Tools
lever Type Each tool bends one size. Capacity:
Tube Benders Openside type. Handy in a Individual tools for bend-
tight spot. Makes precision ing eight sizes from 1/8" to
short radius bends up to 1" O.D. tubing. Will bend
180° with minimum effort. annealed copper, annealed-
Keeps tube round, no marks steel (inc. JIC), stainless
A or scrapes, shows bend degree. Unique extra strong steel and all soft tubing.
hook grips tubing securely.
CATAlOg NUMBER TUBINg NOMINAl (O.D.) sIzE RADIUs TO CENTER OF TUBE WEIgHT EACH TyPE
T-372 1/8 – 3/8 8 ozs. A
B T-373 3/16 – 7/16 9 ozs. A
T-374 1/4 1/8 9/16 12 ozs. B
T-375 5/16 – 11/16 1 lb. 4 ozs. B
T-376 3/8 – 15/16 1 lb. 12 ozs. B
T-378 1/2 3/8 1-1/2 3 lb. 8 ozs. B
T-3710* 5/8 1/2 2-1/4 10 lbs. C
T-3712* 3/4 5/8 3 10 lbs. 8 ozs. C
T-3716* 1 – 3-1/2 10 lbs. 8 ozs. C
* Will bend annealed copper and aluminum tubing only.
C

spring Tube Benders Low cost, tube bending spring operates perfectly in hand bending copper, aluminum and other thin-walled tubing. Bends are true with minimum tubewall collapsing. Belled at one end to facilitate removal. Bright-plated spring wire finish.
CATAlOg NUMBER TUBINg (O.D.) (INCHEs) lENgTH (INCHEs) WEIgHT
T-104 T-105 T-106 T-107 T-108 T-1010 1/4 5/16 3/8 7/16 1/2 5/8 10 10 10 12 12 12 4 ozs. 4 ozs. 5 ozs. 7 ozs. 8 ozs. 10 ozs.
sETs
T-100 T-200 1/4, 3/8, 1/2, 5/8 1/4, 5/16, 3/8, 1/2 10 &12 10 & 12 1-1/2 lbs. 1-1/4 lbs.

Equipment

Tube Flaring & Brazing Tools
T-345K Tube Cutting and Flaring Kit

T-1022
Flaring Tool (45°)

T-220
Double Flaring Tool
(45°)

Tube flaring and cutting has just become a little easier with the convenient T-345K Tube Flaring and Cutting Kit.
This kit features a quality-made Double Flaring Tool offering accurate single flares between 3/16" and 5/8" O.D. tubing. Double flares between 3/16" and 1/2" O.D. tubing.

Check these features:
. Hardened, smooth cone for fast, accurate 45° flares.
. Single and double
flare capability.
. Clamp screw for easy clamping and removal of tubes.
. Flaring Bar installed
from either side of yoke.
. Flares soft copper, brass, aluminum and mild steel (JIC and Bundy) tubing.
Economical, fast operating tool. Quick slip-on aluminum alloy yoke. Easy operating, swivel-type, hard chrome finished cone assures smooth flares.

This new style tool makes single or double flaring easier and quicker than ever. Cam action provides positive, non-slip grip on the tubing with just a squeeze of the handle. Double flaring bar also serves as gauge for correct tubing height to insure perfect flares.
Flaring Capacity:
3/16", 1/4", 5/16", 3/8", 1/2" and 5/8" O.D. for single flares, and up to 1/2" O.D. for double flares. Can be

Refer to safety information on page 1.
T-345K
Components can be ordered separately:
T-345
45° Flaring Tool, Double Flare
Adapters and Plastic Box
T-150
1/8" to 1-1/8" Tube Cutter
T-1422R
T-150 Spare Cutting Wheel

DOUBlE FlARE ADAPTERs
Catalog Number Tube O.D.
T-346x3 3/16"
T-346x4 1/4"
T-346x5 5/16"
T-346x6 3/8"
T-346x8 1/2"

Yoke slips down over top of bar and locks into position with a single turn.
Flaring Capacity:
3/16", 1/4", 5/16", 3/8", 7/16", 1/2", and 5/8" O.D. Forms 45° flares in soft copper, aluminum and brass.
used with copper, aluminum, brass, bundyweld and steel tubing.
Weight:
2 lbs.
T-220 Components can be ordered separately
T-210 Tool for single flaring only
T-221 Double Flaring Bar only.
Flaring Capacity:
3/16", 1/4", 5/16", 3/8" and 1/2"

Refer to safety information

Related Products
on page 1.

Label Sets & Bags
label sets Full assortment available. Each label contains catalog number, illustration, size data and color coding for quick, positive identification of parts. Labels slide easily into slots on drawers and dividers.

self-Adhesive Labels are printed on self
adhesive stock for quick appli
label sets cation. Each label contains an illustration of the part along with the catalog number and size information.

Plastic Bags Eaton heavy-duty plastic bags for brass products come in sizes 5"x6", 6"x10", and 8"x12". The bags include convenient spaces for labeling.

CATAlOg NUMBER DEsCRIPTION
CL-490 Standard brass products, drain and shut-off cocks.
CL-491 Air brake products for copper tubing.
CL-492 Hydraulic brake products.

CL-494 CL-496 Master Set - contains one each of CL-490, CL-491, CL-492. Mini-Barb products.
CL-497 Air brake products for nylon tubing.
CL-498 Polyline products.
CL-499 Push>Connect
CL-500 Selfalign
CL-501 Plastic products
CL-503 QCAB products

CATAlOg NUMBER DEsCRIPTION

FS-800 Air brake products for copper tubing FS-900 Air brake products for nylon tubing FS-1000 Mini-Barb products FS-2100 Polyline products FS-3300 QCAB products W-8022 Standard brass products and drain-shut-off valve
CATAlOg NUMBER DEsCRIPTION QTy.
5x6 PB Plastic Bag 100
6x10 PB Plastic Bag 100
8x12 PB Plastic Bag 100

Size:
16-1/8" wide x 11-3/4" high x 9" deep
Weight:
13 lbs.
Size:
30-1/4" Wide x 14-3/8" Deep x 13-5/8" High
Weight:
45 lbs.
DEsCRIPTION
Individual Drawers
Dividers

stock Cabinet
Weatherhead Part # C-63X Aeroquip Part # FT1602

A cabinet containing 63 drawers that can be divided into two or three sections. The bright color and attractive design make the stock cabinet a nice addition to any store front.
Size:
30-1/4" wide x 25" high x 9-1/4" deep
Weight:
61 lbs.

This Brass Products Cabinet is
Cabinet
a space saving, efficient, easy
Weatherhead Part #
to use addition to the modern
2: C-63X,

store with lobby type sales
1: C-15X,

area. The cabinet requires a
1: CB-63X

minimum of space but does a maximum job merchandising the wide variety of products
Aeroquip Part #
2: FT1602,

in the 126 clear, wide, plastic
1: FT1601,

drawers. An additional 15 large,
1: CB-63X

high impact plastic drawers located in the bottom section provide ample space for those large or heavy special items you may be stocking.
Restocking is easy when you start at the bottom and pull drawers for an order check.
Leave drawers extended that
are low in stock. Now start at top, note quantity needed and
WEATHERHEAD AEROQUIP PART # PART # DEsCRIPTION return drawers to original posi-
C-15X FT1601 15 Drawer Cabinet tion after order is written using standard box quantities listed
C-63X FT1602 63 Drawer Cabinet
CB-63X CB-63X Cabinet Base
CD-15 FT1605 Plastic Drawer for C-15X/
FT1601
142 EATON Brass Products Master Catalog E-BRFI-MC001-E3 February 2008

on labels. Plastic dividers are
provided to section drawers for future expansion when new or additional part numbers are needed.
Display this attractive cabinet with a recommended stock in your lobby and watch your brass product sales increase as the cabinet silently and quickly services your customers. Create those impulse sales that make your business and profits grow!
For complete details on the assortment, see page 143
Size:
68-1/2" high, 30" wide, 15" deep.
Weight:
167 lbs.

Related Products

Assortments
CA-632CO The CA-632CO is an assortment of fast moving brass prod-Brass Products ucts with coverage for most Assortment any application. This space saving assortment includes color coded, illustrated, labels for quick identification by customers of standard products, as well as fuel line, carburetion, metric and domestic hydraulic
CA-632CO CONTENTs
brake and thermoplastic brass of this assortment may vary as fittings in 240 configurations new products are introduced and sizes. Be a supplier to and stock changes in popular-auto dealers, brake specialists, ity. RV shops, plant maintenance shops, truck and bus fleets, contractors, marinas, loggers, shipyards, fishing fleets, farmers and self installers for their brass requirements. Contents
Catalog Catalog Catalog Catalog Catalog Catalog
Number Qty. Number Qty. Number Qty. Number Qty. Number Qty. Number Qty.

05703B-102 5 1540 10 3220x6x4 10 3700x4 5 61x2 10 6829 5 05704B-102 10 202x3 10 3220x8x2 5 3700x6 5 61x3 20 6892 5 05704B-104 5 202x4 10 3220x8x4 10 3750x2 5 61x4 20 69x2 10 05704B-C02 5 202x4x4 10 3220x8x6 5 3750x4 5 61x5 20 69x3 10 05705B-102 10 202x5 10 3220x12x6 2 402x3 10 61x6 10 69x4 10 05705B-104 5 202x5x4 10 3220x12x8 2 402x4 10 61x8 10 69x4x4 10 05705B-C02 10 202x6 10 3300x2 10 402x4x4 5 6100x2 10 69x5 10 05705B-C04 10 202x6x2 5 3300x4 10 402x5 10 6100x3 10 69x5x4 10 05705B-1560 10 2030x4 10 3300x4x2 10 402x5x4 10 6100x4 10 69x6 10 05705B-1561 10 2030x44 10 3300x6 5 402x6 10 62x2 10 69x6x2 5 05706B-102 10 2030x5 10 3300x6x4 5 41x3 10 62x3 10 69x6x6 5 05706B-104 10 2030x6 10 3300x8 5 41x4 10 62x4 10 69x8 5 05706B-106 5 2030x8 5 3300x8x6 5 41x5 10 62x5 10 7818 5 05706B-C02 5 252x3 10 3325x2 10 41x6 10 62x6 10 7828 5 05706B-C04 5 252x4 10 3325x4 10 41x8 5 62x8 5 7829 5 05706B-1568 5 270 5 3325x4x2 5 42x4 5 62x10 1 7896x3 5 05706B-1570 5 302x3 10 3325x6 5 42x6 5 6200x2 10 7896x4 5 100x3 10 302x4 10 3325x6x4 5 48x3 10 6200x3 10 7904 5 100x4 10 302x5 10 3326x2 10 48x4 10 6200x4 10 7906 5 100x5 10 302x6 5 3326x4 10 48x4x4 10 6205-004 10 7908 2 100x6 10 3129x2 5 3326x6 10 48x5 10 64x4 5 7914 2 105x2 10 3150x2 10 3326x8 5 48x5x4 10 64x6 5 7934A 5 105x3 20 3150x4 10 3327x2 10 48x6 10 66x2 10 7935 5 105x4 20 3151x2 10 3327x4 5 48x6x2 5 66x3 10 7936 5 105x5 20 3151x4 10 3328x2 10 48x6x6 5 66x4 10 7937 5 105x6 10 3151x6 10 3328x4 5 48x8 5 66x6 5 7940 5 131x3 10 3151x8 5 3328x6 5 49x4 10 6660 5 7941 5 131x4 10 3152x2 10 3350x2 5 49x4x4 5 6749 1 131x5 10 3152x4 10 3350x4 5 49x5 10 68x2 10 131x6 10 3152x6 10 3350x6 5 49x5x4 5 68x3 10 135 10 3152x8 5 3400x2 10 49x6 10 68x4 10 140 5 3152x12 2 3400x4 10 49x8 5 68x4x4 10 1442 5 3200x2 10 3400x6 5 60x2 50 68x5 10 1443 5 3200x4 5 3400x8 5 60x3 50 68x5x4 10 145 10 3200x4x2 10 3500x2 10 60x4 50 68x6 10 1514 5 3200x6x4 5 3500x4 10 60x5 50 68x6x2 10 1538 10 3200x8x6 5 3600x2 5 60x6 50 68x6x6 5 1548 10 3220x4x2 20 3600x4 5 60x8 20 68x8 5 1539 10 3220x6x2 10 3700x2 10 60x10 10 6809 5

Related Products
Assortments
Brass Products Assortment Weatherhead Part # CA-631 Aeroquip Part # FT1607
CA-631 CONTENTs

This merchandiser will help you organize your brass products in an attractive 63 drawer cabinet. It includes a stock of the 100 fastest moving brass products to better service your customers.To expand, divide the clear, easy to inventory, super sized plastic drawers in half or thirds with plastic dividers provided. Illustrated, color-coded labels in a wide range of connector types provide instant identification of drawer contents. Your lobby and sales will be improved with this modern display set up on a gondola or shelf. Contents may vary as new numbers become available and popularity changes.

Catalog Catalog Catalog Catalog Catalog Catalog
Number Qty. Number Qty. Number Qty. Number Qty. Number Qty. Number Qty.

105x3 20 302x4 10 3200x4x2 10 3326x6 10 48x4x4 10 62x2 10 105x4 20 302x5 10 3200x6x4 5 3327x2 5 48x5 10 62x3 10 105x5 20 302x6 5 3220x4x2 20 3327x4 5 48x5x4 10 62x4 10 105x6 10 402x4 10 3220x6x2 10 3328x2 5 48x6 10 62x5 10 131x3 10 402x5 10 3220x6x4 10 3328x4 5 48x6x6 5 62x6 10 131x4 10 402x6 10 3220x8x2 5 3350x2 5 49x4 5 68x2 10 131x5 10 3150x2 5 3220x8x4 10 3350x4 5 49x6 10 68x3 10 131x6 10 3150x4 5 3220x8x6 5 3400x2 10 60x2 50 68x4 10 135 10 3151x2 10 3300x2 10 3400x4 10 60x3 50 68x4x4 10 145 10 3151x4 10 3300x4 10 3400x6 5 60x4 50 68x5 10 202x3 10 3151x6 10 3300x4x2 10 3700x2 10 60x5 50 68x5x4 10 202x4 10 3151x8 10 3300x6 5 3700x4 5 60x6 50 68x6 10 202x4x4 10 3152x2 10 3300x6x4 5 3750x4 5 61x2 10 68x6x2 10 202x5 10 3152x4 10 3325x2 10 3750x6 2 61x3 10 69x4 10 202x5x4 10 3152x6 10 3325x4 10 41x4 10 61x4 10 69x6 10 202x6 5 3152x8 5 3326x2 10 41x6 10 61x5 10 C-63X or FT1602 1 302x3 10 3200x2 5 3326x4 10 48x4 10 61x6 10 CL-490 1

The brass products assortment mower, or fixit shop. Cabinet Brass Products
contains the fastest moving includes 16 clear plastic draw-SAE 45° Flare, Inverted Flare, ers and color-coded labels for
Assortment
Weatherhead Part #
Compression and Pipe catalog easy identification. The cabinet
FC-161
numbers to give your custom-fits on any shelf and goes to
Aeroquip Part #
ersmaximumcoverageatalow work immediately.
cost. Nuts, sleeves and unions
make an ideal stock for any
small repair, auto, boat, lawn
FT1608
FC-161 CONTENTs

Catalog Catalog Catalog Catalog Catalog Catalog
Number Qty. Number Qty. Number Qty. Number Qty. Number Qty. Number Qty.
105x3 10 302x5 2 402x3 2 49x4 2 61x5 10 69x4 2
105x4 10 3151x2 2 402x4 2 49x5 2 61x6 5 69x5 2
105x5 10 3151x4 2 402x5 2 49x6 2 62x3 5 69x6 2
105x6 5 3220x4x2 5 41x4 2 60x3 20 62x4 5 CL-16-1 1
145 5 3220x6x4 5 41x5 2 60x4 20 62x5 5 FC-16X or 1
202x4 2 3300x2 5 41x6 2 60x5 20 62x6 5 FT1600
202x5 2 3300x4 2 48x4 2 60x6 20 68x4 2
302x3 5 3400x2 5 48x5 2 61x3 10 68x5 2
302x4 5 3400x4 5 48x6 2 61x4 10 68x6 2

Related Products
Assortments
Push>Connect Products Assortment Weatherhead Part # PC-48 Aeroquip Part # FT1613
CA-631 CONTENTs

Eaton PUSH > CONNECT products are designed for quick assembly without the need for a wrench. Ideal for pneumatic applications where space is tight.Then product is also easily disconnected; simply depress the collet ring with two fingers and withdraw the tube. The PC-48 and FT1613 pro vides the 48 most popular PUSH > CONNECT products in a compact, handy plastic box to make your assortment organized and accessible.
Catalog Catalog Catalog Catalog Catalog Catalog
Number Qty. Number Qty. Number Qty. Number Qty. Number Qty. Number Qty.
1162x2 5 1165x6 5 1168x2.5x4 5 1168x6x6 5 1169x4x6S 5 1172x4x4S 5
1162x4 5 1165x8 2 1168x2x4 5 1168x6x8 2 1169x6S 5 1174x2 5
1162x6 5 1166x4 5 1168x4 5 1168x8 5 1169x6x6S 5 1174x4 5
1164x2.5 5 1166x4x4 5 1168x4A 5 1168x8x8 2 1169x8S 2 CL-499 1
1164x4 5 1166x6 5 1168x4x4 5 1169x2.5S 5 1169x8x4S 2 FC-16X or FT1600 1
1164x6 5 1166x6x6 2 1168x4x6 5 1169x2S 5 1171x4S 5
1164x8 2 1168x2 2 1168x5 5 1169x2x4S 5 1171x4x4S 5
1165x2.5 5 1168x2.5 5 1168x5x4 5 1169x4S 5 1171x6S 5
1165x4 5 1168x2.5A 5 1168x6 5 1169x4x4S 5 1172x4S 5

Certification
ISO & QS Certifications
Eaton Hydraulics - Brass Products FACIlITy ClEvElAND, TN vINITA, OK REgIsTRATION ISO9002 ISO/QS9000 ISO14001 REgIsTRAR NUMBER SGSUS98/1495 ULA5225 ULA6947 PRODUCT REsPONsIBIlITy Distribution of Eaton Product Brass Products Manufacturing

Conversion
Conversion Chart
INChEs INChEs INChEs INChEs
FrACTIONs DECIMAls MM FrACTIONs DECIMAls MM FrACTIONs DECIMAls MM FrACTIONs DECIMAls MM
– .0004 0.0100 – .3150 8.0000 11/16 0.6875 17.4630 – 1.1811 30.0000
– .0040 0.1000 21/64 .3280 8.3340 45/64 0.7030 17.8590 1-3/16 1.1875 30.1630
– .0100 0.2500 – .3350 8.5000 – 0.7087 18.0000 1-7/32 1.2190 30.9560
1/64 .0156 0.3970 11/32 .3440 8.7310 23/32 0.7190 18.2560 – 1.2205 31.0000
– .0197 0.5000 – .3543 9.0000 – 0.7283 18.5000 1-1/4 1.2500 31.7500
– .0295 0.7500 23/64 .3590 9.1280 47/64 0.7340 18.6530 – 1.2598 32.0000
1/32 .0313 0.7940 – .3740 9.5000 – 0.7480 19.0000 1-9/32 1.2810 32.5440
– .0394 1.0000 3/8 .3750 9.5250 3/4 0.7500 19.0500 – 1.2992 33.0000
3/64 .0469 1.1910 25/64 .3910 9.9220 49/64 0.7656 19.4470 1-5/16 1.3120 33.3380
– .0590 1.5000 – .3937 10.0000 25/32 0.7810 19.8440 – 1.3386 34.0000
1/16 .0620 1.5880 13/32 .4060 10.3190 – 0.7874 20.0000 1-11/32 1.3440 34.1310
5/64 .0781 1.9840 – .4130 10.5000 51/64 0.7970 20.2410 1-3/8 1.3750 34.9250
– .0787 2.0000 27/64 .4220 10.7160 13/16 0.8125 20.6380 – 1.3779 35.0000
3/32 .0940 2.3810 – .4331 11.0000 – 0.8268 21.0000 1-13/32 1.4060 35.7190
– .0984 2.5000 7/16 .4380 11.1130 53/64 0.8280 21.0340 – 1.4173 36.0000
7/64 .1090 2.7780 29/64 .4530 11.5090 27/32 0.8440 21.4310 1-7/16 1.4380 36.5130
– .1181 3.0000 15/32 .4690 11.9060 55/64 0.8590 21.8280 – 1.4567 37.0000
1/8 .1250 3.1750 – .4724 12.0000 – 0.8662 22.0000 1-15/32 1.4690 37.3060
– .1378 3.5000 31/64 .4840 12.3030 7/8 0.8750 22.2250 – 1.4961 38.0000
9/64 .1410 3.5720 – .4920 12.5000 57/64 0.8906 22.6220 1-1/2 1.5000 38.1000
5/32 .1560 3.9690 1/2 .5000 12.7000 – 0.9055 23.0000 1-17/32 1.5310 38.8940
– .1575 4.0000 – .5118 13.0000 29/32 0.9062 23.0190 – 1.5354 39.0000
11/64 .1720 4.3660 33/64 .5156 13.0970 59/64 0.9220 23.4160 1-9/16 1.5620 39.6880
– .1770 4.5000 17/32 .5310 13.4940 15/16 0.9375 23.8130 – 1.5748 40.0000
3/16 .1875 4.7630 35/64 .5470 13.8910 – 0.9449 24.0000 1-19/32 1.5940 40.4810
– .1969 5.0000 – .5512 14.0000 61/64 0.9530 24.2090 – 1.6142 41.0000
13/64 .2030 5.1590 9/16 .5630 14.2880 31/32 0.9690 24.6060 1-5/8 1.6250 41.2750
– .2165 5.5000 – .5710 14.5000 – 0.9843 25.0000 – 1.6535 42.0000
7/32 .2190 5.5560 37/64 .5790 14.6840 63/64 0.9844 25.0030 1-31/32 1.6562 42.0690
15/64 .2340 5.9530 – .5906 15.0000 1 1.0000 25.4000 1-11/16 1.6875 42.8630
– .2362 6.0000 19/32 .5940 15.0810 – 1.0236 26.0000 – 1.6929 43.0000
1/4 .2500 6.3500 39/64 .6090 15.4780 1-1/32 1.0312 26.1940 1-23/32 1.7190 43.6560
– .2559 6.5000 5/8 .6250 15.8750 1-1/16 1.0620 26.9880 – 1.7323 44.0000
17/64 .2656 6.7470 – .6299 16.0000 – 1.0630 27.0000 1-3/4 1.7500 44.4500
– .2756 7.0000 41/64 .6406 16.2720 1-3/32 1.0940 27.7810 – 1.7717 45.0000
9/32 .2810 7.1440 – .6496 16.5000 – 1.1024 28.0000 1-25/32 1.7810 45.2440
– .2953 7.5000 21/32 .6560 16.6690 1-1/8 1.1250 28.5750 – 1.8110 46.0000
19/64 .2970 7.5410 – .6693 17.0000 – 1.1417 29.0000 1-13/16 1.8125 46.0380
5/16 .3120 7.9380 43/64 .6720 17.0660 1-5/32 1.1560 29.3690 1-27/32 1.8440 46.8310

Conversion
Conversion Chart
INChEs INChEs INChEs INChEs
FrACTIONs DECIMAls MM FrACTIONs DECIMAls MM FrACTIONs DECIMAls MM FrACTIONs DECIMAls MM
– 1.8504 47.0000 2-1/2 2.5000 63.5000 – 3.1496 80.0000 3-25/32 3.7810 96.0440
1-7/8 1.8750 47.6250 – 2.5197 64.0000 3-5/32 3.1560 80.1690 3-13/16 3.8125 96.8380
– 1.8898 48.0000 2-17/32 2.5310 64.2940 3-3/16 3.1875 80.9630 – 3.8189 97.0000
1-29/32 1.9062 48.4190 – 2.5590 65.0000 – 3.1890 81.0000 3-26/32 3.8440 97.6310
– 1.9291 49.0000 2-9/16 2.5620 65.0880 3-7/32 3.2190 81.7560 – 3.8583 98.0000
1-15/16 1.9375 49.2130 2-19/32 2.5940 65.8810 – 3.2283 82.0000 3-7/8 3.8750 98.4250
– 1.9685 50.0000 – 2.5984 66.0000 3-1/4 3.2500 82.5500 – 3.8976 99.0000
1-31/32 1.9690 50.0060 2-5/8 2.6250 66.6750 – 3.2677 83.0000 3-29/32 3.9062 99.2190
2 2.0000 50.8000 – 2.6380 67.0000 3-9/32 3.2810 83.3440 – 3.9370 100.0000
– 2.0079 51.0000 2-21/32 2.6560 67.4690 – 3.3071 84.0000 3-15/16 3.9375 100.0130
2-1/32 2.0313 51.5940 – 2.6772 68.0000 3-5/16 3.3120 84.1377 3-31/32 3.9690 100.8060
– 2.0472 52.0000 2-11/16 2.6875 68.2630 3-11/32 3.3440 84.9314 – 3.9764 101.0000
2-1/16 2.0620 52.3880 – 2.7165 69.0000 – 3.3464 85.0000 4 4.0000 101.6000
– 2.0866 53.0000 2-23/32 2.7190 69.0560 3-3/8 3.3750 85.7250 4-1/16 4.0620 103.1880
2-3/32 20.9400 53.1810 2-3/4 2.7500 69.8500 – 3.3858 86.0000 4-1/8 4.1250 104.7750
2-1/8 2.1250 53.9750 – 2.7559 70.0000 3-13/32 3.4060 86.5190 – 4.1338 105.0000
– 2.1260 54.0000 2-25/32 2.7810 70.6439 – 3.4252 87.0000 4-3/16 4.1875 106.3630
2-5/32 2.1560 54.7690 – 2.7953 71.0000 3-7/16 3.4380 87.3130 4-1/4 4.2500 107.9500
– 2.1650 55.0000 2-13/16 2.8125 71.4376 – 3.4646 88.0000 4-5/16 4.3120 109.5380
2-3/16 2.1875 55.5630 – 2.8346 72.0000 3-15/32 3.4690 88.1060 – 4.3307 110.0000
– 2.2047 56.0000 2-27/32 2.8440 72.2314 3-1/2 3.5000 88.9000 4-3/8 4.3750 111.1250
2-7/32 2.2190 56.3560 – 2.8740 73.0000 – 3.5039 89.0000 4-7/16 4.4380 112.7130
– 2.2440 57.0000 2-7/8 2.8750 73.0250 3-17/32 3.5310 89.6940 4-1/2 4.5000 114.3000
2-1/4 2.2500 57.1500 2-29/32 2.9062 73.8190 – 3.5433 90.0000 – 4.5275 115.0000
2-9/32 2.2810 57.9440 – 2.9134 74.0000 3-9/16 3.5620 90.4877 4-9/16 4.5620 115.8880
– 2.2835 58.0000 2-15/16 2.9375 74.6130 – 3.5827 91.0000 4-5/8 4.6250 117.4750
2-5/16 2.3120 58.7380 – 2.9527 75.0000 3-19/32 3.5940 91.2810 4-11/16 4.6875 119.0630
– 2.3228 59.0000 2-31/32 2.9690 75.4060 – 3.6220 92.0000 – 4.7244 120.0000
2-11/32 2.3440 59.5310 – 2.9921 76.0000 3-5/8 3.6250 92.0750 4-3/4 4.7500 120.6500
– 2.3622 60.0000 3 3.0000 76.2000 3-21/32 3.6560 92.8960 4-13/16 4.8125 122.2380
2-3/8 2.3750 60.3250 3-1/32 3.0312 76.9940 – 3.6614 93.0000 4-7/8 4.8750 123.8250
– 2.4016 61.0000 – 3.0315 77.0000 3-11/16 3.6875 93.6630 – 4.9212 125.0000
2-13/32 2.4060 61.1190 3-1/16 3.0620 77.7880 – 3.7008 94.0000 4-15/16 4.9375 125.4130
2-7/16 2.4380 61.9130 – 3.0709 78.0000 3-23/32 3.7190 94.4560 5 5.0000 127.0000
– 2.4409 62.0000 3-3/32 3.0940 78.5810 – 3.7401 95.0000
2-15/32 2.4690 62.7060 – 3.1102 79.0000 3-3/4 3.7500 92.2500
– 2.4803 63.0000 3-1/8 3.1250 79.3750 – 3.7795 96.0000

Glossary
Alpha/Numeric
A:
abrasion: external damage to a hose assembly caused by its being rubbed on a foreign object; a wearing away by friction.
ABS: Air-Brake Swivel
absorption: regarding hose, the process of taking in fluid. Hose materials are often compared with regard to relative rates and total amounts of absorption as they pertain to specific fluids.
acid resistant: having the ability to withstand the action of identified acids within specified limits of concentration and temperature.
adapter, adaptor:
1.
connectors of various sizes and materials used to change an end connector from one type to another type or one size to another. (i.e., a male SAE to male pipe adapter is often attached to a female SAE to create a male end union connector);

2.
the grooved portion of a cam & groove coupling.

adhesion: the strength of bond between cured rubber surfaces or between a cured rubber surface and a non-rubber surface.
adhesive: a material which, when applied, will cause two surfaces to adhere.
ambient/atmospheric conditions: The surrounding conditions, such as temperature, pressure, and corrosion, to which a hose assembly is exposed.
anchor: a restraint applied to eliminate motion and restrain forces.
anodize, anodized: an electrolytic process used to deposit protective or cosmetic coatings in a variety of colors on metal, primarily used with aluminum.
ANSI: American National Standards Institute.
Application working pressure: unique to customer’s application. See pressure, working.
assembly: a general term referring to any hose coupled with end connectors of any style attached to one or both ends.
ASTM: American Society for Testing and Materials.
axial movement: compression or elongation along the longitudinal axis.
B:
barb: the portion of a connector (coupling) that is inserted into the hose, usually comprised of two or more radial serrations or ridges designed to form a redundant seal between the hose and connector.
barbed and ferrule connector: a two-piece hose connector comprised of a barbed insert (nipple), normally with peripheral ridges or backward-slanted barbs, for inserting into a hose and a ferrule, usually crimped or swaged.
bend radius: the radius of a bent section of hose measured to the innermost surface of the curved portion.
bend radius, minimum:
the smallest radius at which hose or tubing can be used. For Metal Hose: the radius of a bend measured to the hose centerline, as recommended by the manufacturer.
bore:
1.
an internal cylindrical passageway, as of a tube, hose or pipe;

2.
the internal diameter of a tube, hose, or pipe.

braid: the woven portion of a hose used as reinforcement to increase pressure rating and add hoop strength. Various materials such as polyester, cotton or metal wire are used. A hose may have one or more braids, outside or between layers of hose material.
braided ply: a layer of braided reinforcement.
brand: a mark or symbol identifying or describing a product and/or manufacturer, that is embossed, inlaid or printed.
brass: a family of copper/ zinc alloys.
brazing: a process of joining metals using a non-ferrous filler metal having a melting point that is lower than the “parent metals” to be joined, typically over +800oF.
bronze: an alloy of copper, tin and zinc.
BSPP/BSPT:
British Standard Pipe Parallel / British Standard Pipe Tapered. See Connector/ Coupling - Pipe Thread Connectors.
C:
chalking: the formation of a powdery surface condition due to disintegration of surface binder or elastomer by weathering or other destructive environments.
chemical compatibility:
the relative degree to which a material may contact another without corrosion, degradation or adverse change of properties.
chemical resistance: the ability of a particular polymer, rubber compound, or metal to exhibit minimal physical and/or chemical property changes when in contact with one or more chemicals for a specified length of time, at specified concentrations, pressure, and temperature.
cold flexibility: relative ease of bending while being exposed to specified low temperature.
combustible liquid: a
combustible liquid is one having a flash point at or above +100°F (37.8°C).
compound: the mixture of rubber or plastic and other materials, which are combined to give the desired properties when, used in the manufacture of a product.
compression connector:
see connector/coupling - Compression
conductive: the ability to transfer electrical potential.
configuration: the combination of connectors on a particular assembly.
core: the inner portion of a hose, usually referring to the material in contact with the medium.
corrosion: the process of material degradation by chemical or electrochemical means.
corrosion resistance: ability of metal components to resist oxidation.
coupling: a frequently used alternative term for hose end connector.
cover: the outer component usually intended to protect the carcass of a product.
CPE: chlorinated polyethylene, a rubber elastomer.
cracking: a sharp break or fissure in the surface, generally caused by strain and environmental conditions.
D:
date code: any combination of numbers, letters, symbols or other methods used by a manufacturer to identify the time of manufacture of a product.
deburr: to remove ragged edges from the inside diameter of a hose end.
design factor: a ratio used to establish the working pressure of the hose, based on the burst strength of the hose.
DOT: Department of Transportation.

Glossary

Alpha/Numeric
DIN: Deutsche Industrie Norme.
durometer: an instrument for measuring the hardness of rubber and plastic compounds.
E:

eccentricity: the condition resulting from the inside and outside diameters not having a common center.
effusion: the escape, usually of gases, through a material. See permeation.
elastic limit: the limiting extent to which a body may be deformed and yet return to its original shape after removal of the deforming force.
elastomer: any one of a group of polymeric materials, usually designated thermoset, such as natural rubber, or thermoplastic, which will soften with application of heat.
elongation: the increase in length expressed numerically as a percentage of the initial length.

endurance test: a service or laboratory test, conducted to product failure, usually under normal use conditions.
extrude/extruded/ extrusion: forced through the shaping die of an extruder; extrusion may have a solid or hollow cross section.
F:
fabricator: the producer of hose and tubing assemblies.

fatigue: the weakening or deterioration of a material occurring when a repetitious or continuous application of stress causes strain, which could lead to failure.
FDA: United States Food and Drug Administration.

connector/coupling: a device attached to the end of the hose to facilitate connection. The following is only a partial list of types of connectors available:
Compression Connector-
a connector style that seals on a mating tube by compressing an internal ferrule against the tube O.D.
Field Attachable Connector
a connector designed to be attached to hose without crimping or swaging. This connector is not always a reusable type connector.

Inverted Flare Connector
a connector consisting of a male or female nut, trapped on a tube by flaring the end of the tube material to either 37° or 45°.
JIC Connectors -joint Industrial Council (no longer in existence). An engineering group that established an industry standard connector design incorporating a 37° mating surface, male and female styles. These standards are now governed by SAE.

O-ring Connectors -a connector that seals by means of an elastomeric ring of a specified material.
PipeThread Connectors -
NPT -National Pipe Taper. Pipe thread per ANSI B1.20.1
NPTF -National Pipe Tapered for Fuels. (Same as above except dry-seal per ANSI B1.20.3)
NPSH -National Pipe Straight Hose per ANSI B1.20.7
NPSM -National Pipe Straight Mechanical. Straight thread per ANSI B1.20.1
NPSL -National Pipe Straight Loose fit per ANSI B1.20.1
BSPP, BSPT - British Standard Pipe, Parallel, British Standard Pipe Taper. BS21 Quick Connect Connector -a connector designed to quickly connect and disconnect. These connectors come in many styles and types.

Tube Connector -a hose connector of which the mating end conforms to a tube diameter. The mate or male end of a compression connector.
Flammable gases/liquid/ media: a flammable gas, including liquefied gas, is one having a closed cup flash point below +100oF (+37.8oC) and a vapor pressure greater than 25 psi.
(174.2 KPa).
flow rate: a volume of media being conveyed in a given time period.
fluid: a gas or liquid medium.
G:
GPM: gallons per minute.
H:
heat resistance: the property or ability to resist the deteriorating effects of elevated temperatures.
hose: a flexible conduit consisting of a tube, reinforcement, and usually an outer cover.

hydrostatic testing: the use of liquid pressure to test a hose or hose assembly for leakage, twisting, and/or hose change-in-length.
Hytrel: a DuPont registered trademark.
I:
I.D.: the abbreviation for inside diameter.
identification yarn: a yarn of single or multiple colors, usually embedded in the hose wall, used to identify the manufacturer.
ISO: International Organization for Standardization.
J:

JIC: see connector/coupling-JIC.
K:

kinking: a temporary or permanent distortion of the hose induced by bending beyond the minimum bend radius.
L:

layline: the line of printed information that runs parallel on the side of a manufactured hose giving details such as part number, PSI rating, hose size and manufacturing data.
layer: a single thickness of rubber or fabric between adjacent parts.
loop installation: the assembly is installed in a loop or “U” shape, and is most often used when frequent and/or large amounts of motion are involved.
LPG, LP Gas: the abbreviation for liquefied petroleum gas.
M:

MAWP: see pressure, maximum allowable working.
manufacturer’s identification: a code symbol used on or in some hose to indicate the manufacturer.
media, medium: the substance(s) being conveyed through a system.
N:

NAHAD: the abbreviation for the National Association of Hose & Accessories Distributors.
Neoprene: a registered trademark of DuPont.

nipple: the internal member or portion of a hose connector.
nitrile rubber (NB/Buna-N):
a family of acrylonitrile elastomers used extensively for industrial hose.

Glossary

Alpha/Numeric
nominal: a size indicator for reference only.
nomograph: a chart used to compare hose size to flow rate to recommended velocity.
non-conductive: the inability to transfer an electrical charge.
NPT/NPTF: abbreviation for national pipe threads. See connector/coupling - Pipe Thread Connectors.
nylon: a family of polyamide materials.
O:
OAL: see overall length
O.D.: the abbreviation for outside diameter.
OE/OEM: original equipment manufacturer.
oil resistance: the ability of the materials to withstand exposure to oil.
oil swell: the change in volume of a rubber article resulting from contact with oil.
operating conditions: the pressure, temperature, motion, and environment to which a hose assembly is subjected.
overall length (OAL):
the total length of a hose assembly, which consists of the free hose length plus the length of the coupling(s).
oxidation: the reaction of oxygen on a material, usually evidenced by a change in the appearance or feel of the surface or by a change in physical properties.
ozone cracking: the surface cracks, checks or crazing caused by exposure to an atmosphere containing ozone.
ozone resistance: the ability to withstand the deteriorating effects of ozone (generally cracking).
P:
permanent connector: the type of connector which, once installed, may not be removed for re-use.
permeation: the process of migration of a substance into and through another, usually the movement of a gas into and through a hose material; the rate of permeation is specific to the substance, temperature, pressure and the material being permeated.
plating: a material, usually metal, applied to another metal by electroplating, for the purpose of reducing corrosion; typically a more noble metal such a zinc is applied to steel.
ply: an individual layer in hose construction.
polymer: a macromolecular material formed by the chemical combination of monomers, having either the same or different chemical compositions.
pressure: force ÷ unit area. For purposes of this document, refers to PSIG (pounds per square inch gauge).
pressure drop: the measure of pressure reduction or loss over a specific length of hose.
pressure, burst: the pressure at which rupture occurs.
pressure, working: the maximum pressure to which a hose will be subjected, including the momentary surges in pressure, which can occur during service. Abbreviated as WP.
psi (PSI): pounds per square inch.
PTFE: polytetrafluoroethylene, a high molecular weight fluoroplastic polymer with carbon atoms shielded by fluorine atoms having very strong inter atomic bonds, giving it chemical inertness.
Push>Connect:
(Push>Connect Metric, Push>Connect Flow Controls, Push>Connect Plus) A Reusable, easy to assemble connector recommended on compressed air, lubrication, and pneumatic instrumentation applications. Use with approved tubing material.
PVC: polyvinyl chloride. A low cost thermoplastic material typically used in the manufacture of industrial hoses. The operating temperature range is -500oF to +1750oF (-295.5oC to +954.4oC).
Q:
Quick>Connect: A reusable easy to assemble air brake connector used on NT100 series tubing. This connector meets D.O.T. performance requirements.
R:
reinforcement: the strengthening members, consisting of either fabric, cord, and/or metal, of a hose. See ply.
reusable connector/coupling: see connector/coupling, Field Attachable Connectors.
S:
SAE: Society of Automotive Engineers.
shank: that portion of a connector, which is inserted into the bore of a hose.
specification: a document setting forth pertinent details of a product.
spring guard: a helically wound component applied internally or externally to a hose assembly, used for strain relief, abrasion resistance, collapse resistance.
standard: a document, or an object for physical comparison, for defining product characteristics, products, or processes, prepared by a consensus of a properly constituted group of those substantially affected and having the qualifications to prepare the standard for use.
stem: see nipple.
surge (spike): a rapid and transient rise in pressure.
swelling: an increase in volume or linear dimension of a specimen immersed in liquid or exposed to a vapor.
T:
Teflon: a registered trade-
mark of E.I. DuPont. See
PTFE, FEP and PFA.

tube: the innermost
continuous all-rubber or
plastic element of a hose.

tube connector: see con-
nector/
coupling-Tube.

tubing: a non-reinforced,
homogeneous conduit, gen-
erally of circular
cross-section.

V:
vacuum resistance: the measure of a hoses ability to resist negative gauge pressure.
vibration: amplitude motion occurring at a given frequency.
viscosity: the resistance of a material to flow.
W:
weathering: the surface deterioration of a hose cover during outdoor exposure, as shown by checking, cracking, crazing and chalking. working temperature: the temperature range of the application, may include the temperature of the fluid conveyed or the environmental conditions the assembly is exposed to in use.
WP: the abbreviation for working pressure.
The preceding Glossary of Terms, as utilized in the hose industry, includes some definitions from The Hose Handbook, published by the Rubber Manufacturers Association.

Index
Alpha/Numeric
A55SCUx 69 A6845S 104 FS-500 141 PT23004 28 A555 104 A6855 104 FS-504 141 PT23005 28 A555P 106 A6855S 104 FS-800 141 PT23006 28 A555S 104 A6860 104 FS-900 141 PT23008 28 A556P 106 A6860P 106 FS-1000 141 PT24004 28 A557MCUx 69 A6860S 104 FS-2100 141 PT24044 28 A557SCUx 69 B735 104 FS-3300 141 PT24005 28 A655 104 C-15x 142 FT1341 136 PT24006 28 A655S 104 C-63x 142 FT1356 138 PT24008 28 A660 104 C9200 122 FT1356-2-1 138 PT24010 28 A664 113 C9240 122 FT1600 142 PT24012 28 A690 104 CA-631 144 FT1601 142 PT24016 28 A690P 166 CA-63260 143 FT1602 142 T-100 139 A690S 104 CB-63x 142 FT1605 142 T-104 139 A694 113 CD-15 142 FT1607 144 T-105 139 A694S 113 CD-150 142 FT1608 144 T-106 139 A735 104 CL-490 141 FT1613 145 T-107 139 A6690 104 CL-491 141 M41157 122 T-108 139 A6690S 104 CL-492 141 MTP16006 29 T-138 138 A6754 113 CL-493 141 MTP16008 29 T-138B 138 A6754S 113 CL-494 141 MTP16010 29 T-150 137 & 140 A6755 104 CL-496 141 MTP16012 29 T-191 138 A6755S 104 CL-497 141 NT10002 27 T-191B 138 A6759 113 CL-498 141 NT10025 27 T-200 140 A6760 104 CL-499 141 NT10003 27 T-210 140 A6760P 106 CL-500 141 NT10004 27 T-220 140 A6760S 104 CL-501 141 NT10005 27 T-221 140 A6763 104 CL-503 141 NT10006 27 T-345 140 A6763S 104 FC-16x 142 NT10008 27 T-345K 140 A6764 113 FC-161 144 NT10010 27 T-346x 140 A6764S 113 FF90587 115 NT10012 27 T-372 139 A6765 104 FF90588 115 PC-48 145 T-373 139 A6765S 104 FF90589 115 PT20004 27 T-374 139 A6769 113 FF90590 118 PT20044 27 T-375 139 A6769S 113 FF90591 118 PT20005 27 T-376 139 A6770 104 FF90592 118 PT20006 27 T-378 139 A6774 113 FF90593 118 PT20008 27 T-1010 139 A6775 104 FF90594 118 PT20010 27 T-1022 140 A6775S 104 FF90595 117 PT20012 27 T-1422R 140 A6779 113 FF90596 117 PT20016 27 T-1430 37 A6779S 113 FF90597 116 PT23002 28 T-3710 139 A6845 104 FF90598 116 PT23003 28 T-3712 139

Index
Alpha/Numeric
T-3716 139 71x 46 174x 44 1062x 73
TA-1002 136 72x 46 185 107 1064x 75
TP16002 29 74x 44 190 107 1065x 74
TP16025 29 76x 46 202x 33 1066x 73
TP16004 29 100x 32 230 107 1067x 74
TP16005 29 105x 123 & 32 252x 33 1068x 73
TP16006 29 108 107 270 107 1069x 74
TP16008 29 110 111 302x 32 & 125 1070x 74
W1206 136 111 111 320 106 1071x 75
W1212 136 112 111 325 106 1072x 75
W1512 136 113 111 330 106 1073x 73
W15310 94 & 112 114 111 352x 33 1074 123
W20332 94 & 113 115 111 402x 34 1074x 74
5X6 PB 141 116 111 452x 34 1075x 75
6X10 PB 141 117 111 502x 34 1077x 75
8X12 PB 141 118 111 530 106 1078x 73
39x 37 119 111 537 113 1079x 73
40x 37 120 108 601x 49 1100x-MM 135
41x 37 121 111 602x 35 1100x-PP 135
42x 37 122 111 611x 49 1105x 59
43x 38 123 111 621x 50 1105x-M 64
44x 40 124 111 630 106 1107x 60
45x 40 125 111 631x 50 1107x-M 65
46x 38 126 111 632 113 1108x 61
48x 38 127 111 641x 52 1108x-M 65
49x 39 128 111 651x 51 1109x 59
50x 39 130 107 652x 35 1109x-M 64
51x 40 131x 32 661x 50 1110x 37
54x 38 135 107 681x 50 1129x 59
55x 39 140 107 691x 51 1129x-MRP 64
56x 40 145 94 & 107 695 106 1150x-PP 135
59x 122 150 108 700 106 1161x 59
60x 42 162x 43 701x 51 1161x-M 64
61x 42 163x 44 702 113 1162x 60
62x 43 164x 46 702x 35 1162x-M 64
63x 44 165x 45 703 113 1164x 62
64x 46 166x 44 705 108 1164x-M 67
65x 45 168x 43 711x 52 1165x 61
66x 44 169x 45 721x 52 1165x-M 66
68x 43 170x 45 741x 51 1166x 61
69x 45 171x 46 752x 35 1166x-M 65
70x 45 172x 46 0102x 43 & 49 1168Px 70

Index
Alpha/Numeric
1168x 61 134 93 & 101 1460x 85 1568x 128 1168x-M 65 1351 93 & 101 1461x 85 1568Px 128 1168x-MM 65 1360x 91 1462x 85 1569x 130 1169Px 71 1361x 91 1464x 88 1569Px 130 1169x-5 62 1362x 91 1465x 87 1570x 130 1169x 62 1364x 93 1466x 86 1570Px 130 1169x-M 66 1366x 92 1468x 86 1571x 132 1169x-MPTS 66 1368x 91 1469x 87 1571Px 132 1169x-SMM5 66 1369x 92 1469x-L 87 1572x 131 1171Px 71 1369x-L 92 1470x 87 1572Px 131 1171x-M 67 1371x 93 1471x 88 1574x 128 1171x-S 62 1372x 93 1472x 88 1574Px 128 1172Px 71 1380x 92 1474x 86 1584x 132 1172x-M 67 1408 119 1477x 88 1584Px 132 1172x-S 63 1410 119 1480x 86 1596 121 1172x-MM5 67 1421-7 109 1482x 89 1611x 43 & 49 1174x 60 1421-18 109 1484x 89 1621x 50 1174x-M 65 1421-24 109 1485x 89 1631x 50 1180x 60 1421-32 109 1502x 133 1641x 52 1180x-M 64 1421-60 109 1502Px 133 1651x 51 1181x 63 1421-60A 109 1512 99 & 120 1661x 50 1183x 63 1422 109 1513 121 1681x 50 1184x 63 1423 109 1514 121 1691x 51 1185x 63 1424A 108 1518 33 & 39 & 121 1701x 51 1202x 54 1425A 108 1521 39 & 1 21 1711x 52 1260x 54 1426A 108 1522 33 & 39 & 121 1721x 52 1261x 54 1427 109 1529x 133 1741x 51 1262x 54 1428 119 1529Px 133 1800Kx 83 1264x 56 1429 119 1531x 133 1800T 83 1266x 55 1432 119 1553 33 & 39 & 121 1800TRK 83 1268x 55 1433 109 1554 33 & 39 & 121 1829x 83 1269x 56 1437 120 1561x 132 1861x 78 1270x 56 1439 120 1561Px 132 1862x 78 1271x 56 1440 120 1562x 129 1864x 81 1272x 56 1441 123 1562Px 129 1865x 80 1274x 55 1442 124 1563 33 & 39 & 121 1866x 79 1340 94 & 101 1443 124 1564x 131 1868x 79 1341 94 & 101 1444 120 1564Px 131 1869x 80 1342 94 & 101 1445 120 1565x 131 1869x-L 80 1343 94 & 101 1446 120 1565Px 131 1869x-S 81 1344 93 & 101 1447 120 1566x 129 1870x 81 1345 93 & 101 1451 109 1566Px 129 1871x 81

Index
Alpha/Numeric
1871x-S 82 1937 134 6660 109 7771 123 1872x 82 1938 134 6700 106 7805 124 1872x-S 82 1939 134 6703 106 7812 124 1873x 78 1940 134 6707 114 7817 123 1874x 78 1942 134 6708 114 7818 123 1877x 82 1943 134 6709 114 7828 123 1880x 79 1944 134 6715 105 7829 123 1880x-S 80 1945 134 6719 112 7896x 123 & 32 1883x 83 1946 134 6724 112 7897 123 1900 134 1948 134 6729 112 7898 124 1901 134 1949 134 6737 114 7900 124 1902 134 2030x 42 & 48 6747 114 7901 124 1903 134 3129x 98 6748 114 7904 124 1906 134 3150x 98 6749 114 7905 124 1907 134 3151x 98 6783 108 7906 124 1908 134 3152x 98 6788 107 7908 123 1911 134 3153x 98 6800 105 7909 123 1912 134 3200x 98 6804 114 7910 123 1913 134 3220x 99 6805 105 7911 123 1914 134 3250x 99 6809 114 7912 123 1915 134 3300x 99 6810 105 7913 123 1916 134 3325x 100 6815 105 7914 124 1917 134 3326x 100 6820 105 7915 122 & 123 1918 134 3327x 100 6824 113 7916 122 & 123 1920 134 3328x 100 6825 105 7917 123 1921 134 3329x 100 6828 114 7933 124 1922 134 3330x 100 6829 113 7934A 125 1923 134 3331x 100 6891 112 7935 124 1924 134 3350x 101 6892 112 7936 124 1925 134 3400x 101 6893 112 7937 124 1927 134 3500x 102 7502 110 7940 125 1928 134 3600x 102 7504 110 7941 125 1929 134 3700x 102 7506 110 7970 124 1930 134 3750x 102 7508 110 7975 124 1931 134 3950x 102 7509 110 7977 122 1932 134 6100x 96 7709 124 7978 122 1933 134 6200x 96 7727 123 1935 134 6400x 96 7732 123 1936 134 6600 108 7765 124

CNMEC Technology (Beijing) Co., Ltd.
Rm2115, T1-C Tower, Wangjing SOHO, Chaoyang District, Beijing China.
Tel：+86-10-8428 2935, 84278 3983; 8428 9077 Fax：+86-10-84288762
Wechat / Mobile phone：+86-10-13910122694
WeChat ID // a84282935
Website: www.increaseinc.cn
E-Mail: sales@cnmec.com

Copyright® 2022-2028 By Increase Technologies - All rights reserved.